postium PRM-207Q LCD Rack Monitor User Manual

: June 13, 2024
: postium

Table of Contents

Warning
Features
Feature Name & Functions
OSD Menu Organization & Adjustment
Other Functions
System Defaut Value
Product Specification
Documents / Resources

LCD Rack Monitor postium PRM 207Q LCD Rack Monitor PRM-207Q LCD Rack Monitor User Manual

Warning

Always use set voltage.
– DC 12V
If liquid is spilled on or impacts this product, please disconnect the product immediately and contact for professional help before continuing use.
Keep unit disconnected during extended periods of disuse.
Keep unit in a well-ventilated place to prevent overheating.
Do not install the product near any heat-generating equipment.
Keep the product out of direct sunlight or dusty areas.
Only clean the product with a noncommercial, mild, and neutral detergent.
When transporting the product, make use of its original packaging for safer transport.

FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential to correct the interference at his own expense Change or modifications not expressly approved by the manufacturer responsible for compliance void the user’s authority to operate the equipment.
Warning!! :
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.

Features

Multi-Format PRM-207Q Rack Monitor Contains the following features :

Compatible with various SDI Signals
The product is compatible with varied SDI Signals
-480i,576i,720p,1035i,1080i,1080p,1080psf, 2K
Wide Varieties of Markers & Safety Areas
Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan)
High Resolution(960X540)/LED Backlight
24Bit RGB CMOS Interface Panel
Tilt of LCD Module: ±15°
Dynamic UMD(Under Monitor Display)
Small, medium, and large size display.
Possible to control monitor to the maximum value of 100 by Set ID Menu.
BLUE ONLY/MONO
H/V Delay
Pixel To Pixel
Provides both full screen and unscaled native image.
DC Compatible
The product is powered by a normal 12V source.
Additional Features
Active loop-thru/SDI, 200:1 Contrast Ratio, 250 cd/m² Brightness, OSD user interface, Rack Mountable, Cooling Fan

Feature Name & Functions

< FRONT>

postium PRM 207Q LCD Rack Monitor - Functions

[MENU] button
Used to activate the OSD Menu.
[UP] button
Used to navigate menu during OSD Menu activation.
It may also be used to select Aspect Marker during OSD Menu non-activation.
[DOWN] button
Used to navigate menu during OSD Menu activation.
It may also be used to select Aspect Marker during OSD Menu non-activation
[ENTER] button
Used to confirm a chosen value (or mode) within the OSD Menu.

< REAR>

postium PRM 207Q LCD Rack Monitor - Functions 1

SDI A-IN (BNC) SDI A signal input terminal
SDI-OUT (BNC)
SDI signal output terminal
DC IN (3 pins)
Used to supply DC power; 12V
RS422 IN/OUT (RJ45)
Pin 1| TX-
---|---
Pin 2| TX+
Pin 3| RX-
Pin 6| RX+
Pin 7, 8| Ground
Pin 4, 5| N.0

Used to display a dynamic UMD

PGM SW(mini slide switch)
Used to download a program.
UMD SW(mini slide switch)
Used to active a dynamic UMD

postium PRM 207Q LCD Rack Monitor - Functions 5

[1] MAIN – Color

Color Temp (Default Setting – 6500K)
This item controls Color Temperature with presets of 3200K, 5600K, 6500K, 9300K, and User1,
User2, and User3 mode.
User
On User Mode, the user may select and control R, G, & B GAIN, or BIAS values by using the [UP]/[DOWN]/[ENTER] buttons.
Color Copy (Default Setting – 6500K)
In User mode, user can copy the presets of 3200K, 5600K, 6500K, or 9300K to make the custom adjustment by using the [UP]/[DOWN]/[ENTER] buttons.

[2] MAIN – Marker

Marker (Default Setting – On)
Used to show MARKER on the screen. The type of marker at work may be selected on the other menu.
-This function is not available in Pixel to Pixel and HV Delay modes.
Line Marker (Default Setting – Off)
MODE| MARKER CLASS
---|---
HD / SD 16:9| 16:9, 4:3, 4:3 ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3
SD 4:3| 16:9

This selects the marker type when the MARKER is displayed on the screen. Compatible MARKER types are as follows:

Center Marker (Default Setting – Off)
This item displays the CENTER MARKER on the screen.
Safety Area (Default Setting – Off)
This item controls the size of the SAFETY AREA between 80%, 85%, 88%, 90%, 93%, and 100%.
-Line Marker, Center Marker, and Safety Area functions operate only after activating the MARKER function to the‘ On’ position in the Marker Menu.

System Default (Default Setting – No)
User can use the System Default Menu to initialize the values of the monitor.
Source ID (To make active, off the Marker function)
This item is used to activate the Source ID display by selecting Manual(BG), Manual(Char), UMD(Small), UMD(Medium), or UMD(Large).
-This function is only available in same Set ID with UMD controller’s.
Source ID Character
This item is used to customize the Source ID display. (A~Z, a~z, 0~9, and special characters).
-This function is only available if the Source ID is selected on Manual.
Source ID Position (Default Setting – Left Top)
This item controls the position of the Source ID display. (Top-Left, Top- Center, Top-Right, Bottom-Right, Bottom-Center, Bottom-Left)
-This function is only available if the Source ID is selected on Manual.
Source ID Color (Default Setting – Blue) This item is used to change the color of Source ID display by selecting blue, white, red, green, black, or yellow.
Set ID (Default Setting – 0) This item controls the Set ID settings for Dynamic UMD. The value should be within range between 0 and 126.
Back Light This item controls the LED backlight setting. The value should be within ranges between MIN(0) and MAX(50).

Blue & Mono
You may remove R(red) and G(green) from the input signal and show the image only with a B(blue) signal. Menu may be set to ‘Mono’ to change the screen to MONO mode.
(This mode uses only the Luminance value)
Scan
This item controls the transition from OVER SCAN mode to ZERO SCAN mode.
Mode changes in the order of Zero Scan -> Over Scan -> Pixel To Pixel -> Zero Scan.
-In Pixel To Pixel mode, the Marker Feature and Menu are disabled automatically.
-In Pixel To Pixel mode, pressing the Enter button rotates the position of display.
Aspect Ratio
This item toggles aspect ratio in SD from standard to anamorphic.
-SD Signal only (Disables automatically in any other signal including No signal)
HV Delay
This item activates the HV Delay mode.
-In HV Delay mode, Marker Feature and Menu are disabled automatically.
Firmware Version
This item is the firmware version of the system.
License
Licensed by Postium Korea.

Other Functions

[1] Line Marker

A line marker which is enabled by default, displays aspect lines with the input signal.
To display the [Line Marker] mode, use the [UP]/[DOWN] buttons to select aspect lines as below.

postium PRM 207Q LCD Rack Monitor - Line Marker

[2] PIXEL TO PIXEL

Pixel to Pixel mode in PRM-207Q monitor displays the input signal without scaling the image
To activate the [Pixel to Pixel] mode, access the Scan Menu in System Menu and select [Pixel to Pixel].
In the [Pixel To Pixel] mode, use the [UP]/[DOWN] buttons to toggle between 1:1 scan sections.

Input| Action Button|

Available Modes

---|---|---
HD 1080i / 1080p| [UP] (Clockwise)| Center -> Left-Top -> Mid-Top -> Right-Top -> Right-Mid -> Right- Bottom -> Mid-Bottom -> Left-Bottom -> Left-Mid -> Center -> …
[DOWN] (Opposite)| Center -> Left-Mid -> Left-Bottom -> Mid-Bottom -> Right- Bottom
-> Right-Mid -> Right-Top -> Mid-Top -> Left-Top -> Center -> …

postium PRM 207Q LCD Rack Monitor - OSD change

Input| Action Button|

Available Modes

---|---|---
HD 720p| [UP] (Clockwise)| Center -> Left-Top -> Right-Top -> Right-Bottom -> Left-Bottom -> Center -> …
[DOWN] (Opposite)| Center -> Left-Bottom -> Right-Bottom -> Right-Top -> Left- Top -> Center -> …

postium PRM 207Q LCD Rack Monitor - OSD change 1

Pixel To Pixel mode is not available in Graphic mode.
Pixel To Pixel mode is available in SD mode, but 1:1 sections cannot be rotated through as with HD sources.
Positions in HD Signal 1080i/1080p mode
Position in HD Signal 720p mode
Source ID Position (Manual Only)

System Defaut Value

MENU|

VALUE

---|---
Color| Color Temp| 6500K
Gain RED (1/2/3)| 0
Gain GREEN (1/2/3)| 0
Gain BLUE (1/2/3)| 0
Bias RED (1/2/3)| 0
Bias GREEN (1/2/3)| 0
Bias BLUE (1/2/3)| 0
Color Copy| 6500K
Marker| Marker| On
Line Marker| Off
Center Marker| Off
Safety Area| Off
System [Page1]| System Default| No
Source ID| Off
Source ID Character| C A M – 1
Source ID Position| Left Top
Source ID Color| Blue
Set ID| 0
Back Light| different for each set
System [Page2]| Blue & Mono| Off
Scan| Zero Scan
Aspect Ratio| 16:9
HV Delay| Off

Product Specification

Input (1 Screen)*	1 x BNC	SDI 2 Channel Input
Output (1 Screen)*	1 x BNC	SDI Output (Active Through Out)
Input Signal*	HD-SDI	1.458Gbps
SD-SDI	270Mbps
SDI Input Signal Formats*	SMPTE-274M	1080i (60/59.94/50)

· All specifications are subject to change without notice.

Specification is for (1) screen out of 7 display screens.

Postium Korea
Postium Bldg. 2F, 433-34 Kalhyun-Dong,
Eunpyoung-Gu, Seoul, 122-811, Korea
Tel : +82-2-354-6055
Fax : +82-2-354-6056
www.postium.com