radxa ROCK4SE Raspberry Pi Alternative Arrives with M.2 M Key Connector Installation Guide
- June 4, 2024
- radxa
Table of Contents
radxa ROCK4SE Raspberry Pi Alternative Arrives with M.2 M Key Connector I
Essentials You Need
- ROCK Pi 4, Model A or Model B
- Power adapter with USB type C port equal or larger than 15W
- MicroSD Card or eMMC module with eMMC-to-uSD adapter board
- Keyboard & Mouse
- Monitor with HDMI input
Quick Installation Guide
- Download Image Writer tool Etcher and OS images from http://rock.sh/pi4
- If you use eMMC module, put eMMC module to uSD adapter board, and inset uSD adapter board to card reader. If you use microSD card, just plug the microSD card to card reader.
- Plug the card reader to PC.
- Open Etcher, select the OS Image, select the card reader drive, and run FLASH.
- Plug the eMMC module or microSD card to your ROCK Pi, connect HDMI to monitor, plug in mouse and keyboard, power on and enjoy!
Support
Forum: http://forum.radxa.com
Wiki: http://wiki.radxa.com/Rockpi4
Email: support@radxa.com
FCC WARNING
FCC Caution : Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
-
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
15.105 Information to the user. -
For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
-
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match the
intended destination.
The firmware setting is not accessible by the end user.
The final end product must be labelled in a visible area with the following:
“Contains Transmitter Module 2A3PA-ROCK4SE”
Requirement per KDB996369 D03
List of applicable FCC rules
List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3
Explanation: This module meets the requirements of FCC part 15C(15.247).it specifically establish the 6dB Bandwidth,, Peak Output Power, Radiated Spurious Emission, PowerSpectral Density, Restricted Band of Operation and Band Edge (Out of Band Emissions) Measurement
Limited module procedures
If a modular transmitter is approved as a “limited module,” then the module manufacturer isresponsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions.
A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval.
This limited module procedure is also applicable for RF exposure evaluation
when it is necessary to demonstrate compliance in a specific host. The module
manufacturer must state how control of the product into which the modular
transmitter will be installed will be maintained such that full compliance of
the product is always ensured. For additional hosts other than the specific
host originally granted with a limited module, a Class II permissive change is
required on the module grant to register the
additional host as a specific host also approved with the module.
Explanation: The module is a single module.
Trace antenna designs
For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements.
- Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna);
- Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered);
- The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout;
- Appropriate parts by manufacturer and specifications;
- Test procedures for design verification; and
- Production test procedures for ensuring compliance.
The module grantee shall provide a notice that any deviation(s) from the
defined parameters of the antenna trace, as described by the instructions,
require that the host product manufacturer must notify the module grantee that
they wish to change the antenna trace design. In this case, a Class II
permissive change application is required to be filed by the grantee, or the
host manufacturer can take responsibility through the change in FCC ID (new
application) procedure followed by a Class II permissive change application.
Explanation: No, The module has no tracking antenna design, is Chip
antenna.
RF exposure considerations
It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable – xx cm from a person’s body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID (new application).
Explanation: This module complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment, This equipment should be installed
and operated with a minimum distance of 20 centimeters between the radiator
and your body.” This module is designed to comply with the FCC statement,
FCC ID is: 2A3PA-ROCK4SE.
Antennas
A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
For situations where the host product manufacturer is responsible for an
external connector, for example with an RF pin and antenna trace design, the
integration instructions shall inform the installer that unique antenna
connector must be used on the Part 15 authorized transmitters used in the host
product. The module manufacturers shall provide a list of acceptable unique
connectors.
Explanation: The EUT only have one Chip antenna, Yes, the module contains
a permanently attached antenna, The antenna gain is 2dBi.
Label and compliance information
Grantees are responsible for the continued compliance of their modules to the
FCC rules. This includes advising host product manufacturers that they need to
provide a physical or e-label stating “Contains FCC ID” with their finished
product. See Guidelines for Labeling and User Information for RF Devices – KDB
Publication 784748.
Explanation: The host system using this module, should have a label in a
visible area indicating the following texts:
“ Contains FCC ID: 2A3PA-ROCK4SE
Information on test modes and additional testing requirements5
Additional guidance for testing host products is given in KDB Publication
996369 D04 Module Integration Guide. Test modes should take into consideration
different operational conditions for a stand-alone modular transmitter in a
host, as well as for multiple simultaneously transmitting modules or other
transmitters in a host product. The grantee should provide information on how
to configure test modes for host product evaluation for different operational
conditions for a stand-alone modular transmitter in a host, versus with
multiple, simultaneously transmitting modules or
other transmitters in a host.
Grantees can increase the utility of their modular transmitters by providing
special means, modes, or instructions that simulate or characterizes a
connection by enabling a transmitter. This can greatly simplify a host
manufacturer’s determination that a module as installed in a host complies
with FCC requirements.
Explanation: WiFiRanger, A LinOra Company can increase the utility of our
modular transmitters by providing instructions that simulate or characterize a
connection by enabling a transmitter.
Additional testing, Part 15 Subpart B disclaimer
The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15
Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Explanation: The module is without unintentional-radiator digital
circuity, so the module does not require an evaluation by FCC Part 15 Subpart
B. The host shoule be evaluated by the FCC Subpart B.
This product uses Chipantenna with a maximum antenna gain of 2dBi
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>