AEOTEC ZWA009 AërQ Temperature & Humidity Sensor User Guide
- June 13, 2024
- Aeotec
Table of Contents
AEOTEC ZWA009 AërQ Temperature & Humidity Sensor
Product Information
- Product Name: ZWA009
- Used in this guide: PIN: 123456 SN: 201808
- Action Button: Used to perform certain actions on the device.
- Double-sided Tape for Magnet: Used to attach the device using the magnet feature.
- Important Safety Information: Contains small parts; keep away from children.
- Quick Start: For detailed instructions, refer to https://manual-hub.com/.
- Gateway Compatibility: Check aeotec.com/z-wave-gateways for compatibility with your Z-Wave gateway.
- Declaration of Conformity: ZWA009 is compliant with RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008, and EN50581:2012. Full declaration available at support.aeotec.com/ths/doc
- FCC ID: 2AOGIZWA009
FCC Warning:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit than the receiver.
- Consult the dealer or a radio/TV technician for help.
Product Usage Instructions
- If your Z-Wave gateway supports SmartStart:
- Scan the QR Code on the device for SmartStart inclusion.
- If your gateway does not support SmartStart:
- Set your Z-Wave gateway into its “add device” mode. Refer to the gateway’s manual for assistance.
- Press the sensor’s button 3 times within 1.5 seconds. The button is located on the top middle section of the device.
- If pairing is successful, the sensor’s LED will change to a green color for 3 seconds.
For more help and information on features, configuration options, and technical specifications, visit aeotec.com/contact or refer to the manual at the link provided.
Important safety information.
Please read this and the online guide(s) at support.aeotec.com/ths carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and / or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources. aërQ Temperature & Humidity Sensor is intended for indoor use in dry locations only. Do not use in locations with direct water contact. Contains small parts; keep away from children.
Quick start.
The following will step you through installing aërQ Temperature & Humidity Sensor and connecting it to your Z-WaveTM network.
- Remove the battery insulation strip from your aërQ Temperature & Humidity Sensor.
- Add aërQ Temperature & Humidity Sensor to your Z-Wave network;
- a. If your Z-Wave gateway supports SmartStart: scan the QR code on aërQ Temperature & Humidity Sensor using the gateway’s app. Your sensor will join your Z-Wave network automatically.
- b. If your gateway does not support SmartStart;
- i. Set your Z-Wave gateway into its ‘add device’ mode. Refer to the gateway’s manual if you are unsure of how to perform this step.
- ii. Press the sensor’s button 3 times within 1.5 seconds; it is located on the top middle section of this device.
- iii. When aërQ Temperature & Humidity Sensor is joining your Z-Wave network, its LED will blink green and red.
- iv. If pairing is successful, your sensor’s LED will change to a green colour for 3 seconds before turning off. If pairing failed, your sensor’s LED will flash red 3 times; repeat the step or contact us for further support if needed.
- After connecting aërQ Temperature & Humidity Sensor to your gateway, test it in your chosen installation location by pressing the action button. If its LED briefly blinks green, it has a good connection to your gateway. Place or affix it in place using the included adhesive.
The aërQ Temperature & Humidity Sensor is now a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software’s user guide for precise instructions.
Get help & learn more
Should you encounter any problem with aërQ Temperature & Humidity Sensor, visit support.aeotec.com/ths or contact our support team via aeotec.com/contact. You can also learn more about your sensor’s features, configuration options, and technical specifications at the link.
Gateway compatibility.
To see if your sensor is known to be compatible with your Z-Wave gateway,
please refer to aeotec.com/z-wave-gateways.
Declaration of Conformity. Aeotec Limited declares that ZWA009 is in
compliance with the essential requirements and other relevant provisions of
RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008 and EN50581:2012. The full text
of the declaration is available from
support.aeotec.com/ths/doc
FCC ID: 2AOGIZWA009
In Europe contact Aeotec Group GmbH; Große Johannisstraße 7, 20457 Hamburg,
Germany.
© & ™ Aeotec Limited.
Version: 501000900001 – AA
References
- Contact Us – Aeotec
- Controllers - Aeotec
- Support – Aeotec
- Aeotec - Pioneers of Smart Home, SmartThings, Matter & Zigbee
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>