belltech 15213 2 Inch TO 3.5 Inch Rear Lift Coilover Kit Installation Guide
- June 13, 2024
- belltech
Table of Contents
belltech 15213 2 Inch TO 3.5 Inch Rear Lift Coilover Kit
Product Information
The Belltech 15213 2 to 3.5 Rear Lift Coilover Kit is designed for GM 1500 SUVs, both 2WD and 4WD, manufactured in 2021 and onwards. It is a high-quality product developed to provide maximum performance and improve the look and feel of your vehicle.
Belltech Customer Support:
- Phone: 1-800-445-3767
- Email: info@belltech.com
Product Usage Instructions
Before You Begin
Before starting the installation process, ensure that all parts are present. If any part is missing, please contact Belltech customer service for assistance.
Safety Information
Ensure that you do not work under a vehicle supported only by a jack.
Always use support stands placed securely in the manufacturer’s specified
locations. Use proper safety equipment and eye/face/hand protection throughout
the installation process.
Installation Assistance
If you need assistance with the installation or have any questions or
concerns, please contact Belltech customer support specialists. They are
trained to guide you through the installation process.
Qualified Mechanic Recommendation
We recommend that a qualified mechanic, at a properly equipped facility,
perform the installation. Having an assistant available during the
installation process can be very helpful.
Before Driving Your Vehicle
Prior to driving your vehicle after the installation, perform the following
checks:
- Inspect brake hoses, cables, and other components for any interference.
- Check for wheel/tire to chassis/body interference.
If any issues are found, review the installation instructions to ensure no steps were missed and correct any problems.
Alignment and Hardware Check
After installation, it is important to:
- Align your vehicle immediately.
- Check all hardware and re-torque at intervals for the first 10,100, and 1000 miles.
Vehicle Handling and Off-Road Performance
Some of Belltech’s products are designed to improve off-road performance. However, leveling/lifting your vehicle may alter its center of gravity. Exercise extreme care when operating your vehicle to prevent rollover and/or loss of control.
Driving Characteristics and Safety
Any changes in your vehicle’s suspension may affect its handleability. Test-
drive your vehicle in a remote location to become accustomed to the revised
driving characteristics. Perform a headlight check and adjustment.
Never operate your modified vehicle under the influence of drugs, alcohol, or lack of adequate sleep. Failure to drive any modified vehicle in a safe manner may result in harm or death.
PART NUMBER: 15213
2” TO 3.5” REAR LIFT COILOVER KIT
GM 1500 SUV 2WD/4WD | 2021+
THANK YOU
Thank you for choosing our high quality Belltech product. We have spent a
great deal of time developing our line of products so that you will receive
maximum performance with minimal difficulty during installation. Soon your
vehicle will be on the road looking and feeling much improved.
Please take a moment to read all instructions and warnings prior to installation of your new Belltech product and before operating your vehicle. If you have any questions or concerns regarding any step in the installation pro-cess, please do not hesitate to call or email our customer support specialists who are trained to help you through any portion of this process.
Before You Begin:
It is of the utmost importance that you confirm all of the components listed
on the parts list is in the kit. You can find this list located on the last
page(s) of your instructions. Do not begin installation if any part is
missing. Instead, please call our Belltech customer service specialists.
Belltech Customer Support:
Phone: 1-800-445-3767
Email: info@belltech.com
Safety Information
Warning: Do not work under a vehicle supported only by a jack. Place
support stands securely under the vehicle in the manufacturer’s specified
locations unless otherwise instructed.
Proper use of safety equipment and eye/face/hand protection is absolutely
necessary when performing any of the following instructions.
We strive for an exceptional experience for all our valued customers. If for
any reason you need assistance with your Belltech products, please do not
return the product to the store you purchased from, but rather call our
dedicated customer service experts, from 6am to 5pm PST.
We recommend that a qualified mechanic, at a properly equipped facility,
perform this installation.
It is very helpful to have an assistant available during installation.
Before Driving Your Vehicle
It is important to double-check all brake hoses, cables, and other components
to be sure there is no interference. You must also check for wheel/tire to
chassis/body interference. If any issues are found, review your installation
instructions to be sure no steps were missed and any problems are corrected.
Make sure your vehicle is aligned immediately following installation.
Check all hardware and re-torque at intervals for the first 10, 100, and 1000
miles.
Some of Belltech’s products are designed to improve your vehicle’s off-road
performance. Leveling/lifting your vehicle may result in an altered center of
gravity. It is crucial to use extreme care when operating your vehicle to
prevent rollover and/or loss of control.
Any changes in your vehicle’s suspension may result in transformed
handleability. Please test-drive your vehicle in a remote location so you can
become accustomed to the revised driving characteristics.
Perform headlight check and adjustment.
Failure to drive any modified vehicle in a safe manner may result in harm or
death.
Never operate your modified vehicle under the influence of drugs, alcohol, or
lack of adequate sleep.
Always wear your seatbelt.
Recommended Tools:
- Properly rated floor jack
- Support stands
- Wheel chocks
- Metric socket wrench set
- Metric wrench set
- Tape measure
- Marking Pen
Specialty Tools:
- High quality spring compressor
- Torque wrench up to 150ft/lbs
Technician note:
Before making any adjustments to your new Belltech coilover, please be sure to
loosen the set screw. Failure to do so will damage the threads. After the
adjustments are made, you may then tighten the set screw to keep the settings
in place.
Installation Preparation
Before beginning the installation process, measure the hub to fender heights for your vehicle and record them in the “Before” section. After your vehicle has been modified, record the new measurements in the, “After” section. This way, you can compare the resulting height to the original. When taking the measurements, measure vertically from the center of the wheel to the inner edge of the fender.
Jacking, Supporting, and Preparing the Vehicle
-
Park your vehicle on a smooth, level, concrete or seasoned asphalt surface.
-
Block the rear wheels of the vehicle using wheel chocks. Make sure the vehicle’s transmission is in “PARK” (automatic) or 1st gear (manual).
-
Activate the parking brake.
-
Loosen, but do not remove, the front wheel lug nuts.
-
Lift the front of the vehicle off the ground using a properly rated floor jack. Lift the vehicle so the front tires are approximately 6-8 inches off the ground.
-
Place support stands rated for the vehicles weight. The stands should be positioned in the factory specified locations. (Refer to owners manual). Prior to lowering the vehicle onto stands, make sure the support stands will contact the chassis. It is very import-ant that the vehicle is properly supported to prevent any harm to ones self or to the vehicle.
-
Lower the vehicle slowly onto the stands.
-
Remove the front wheels.
Technician reminder:
Never work under a vehicle supported only by a jack. It is necessary to place support stands securely under the vehicle in the manufacturer’s specified locations unless otherwise instructed.
OEM STRUT REMOVAL -
Remove the bolt holing the lower strut to the lower control arm.
-
Remove the two brake line bolts and one lower control arm bolt attaching the control arm to the spindle.
-
Remove the 3 flanged nuts that secure the top of the strut to the chassis.
-
Push the lower control arm down until the strut is able to clear the control arm.
-
Drop the old strut out of the strut tower
-
Carefully mount the entire spring/strut assembly in the fixture. To ease the installation of the new strut , mark the position of the top mount in relationship to the upper spring isolator and strut body.
-
Compress the spring until tension is relieved from the strut.
Technician note:
The installation photograph shown was taken at a professional instal-lation shop. It is important to use a spring compressor to compress the spring before removing the top mount bolt. Failure to do so may result in serious injury. -
Remove the strut top nut from the assembly.
-
Remove the shock and bump stop from the assembly. You will reuse to OE top mount.
Belltech Coilover Height Setup and assembly -
The coilover comes as shown below. Remove the nylock nut from the top of the Belltech coilover.
-
Using the table below as reference, remove the main spring and slide the required packers onto the strut rod.
2021+ GM 1500 SUV 2WD/4WD
Lift (Inches)
| Perch height (milli- meters/inches)|
15mm Packer
2”| 170mm/6.7in| 0
3”| 190mm/7.5in| 1
3.5”| 200mm/7.9in| 2
Technician note:
Belltech uses packers to maintain the correct bump stop engagement at various
height ranges. Using the appropriate packer will prevent excessive body roll.
If a packer is needed, according to the above charts, please place the packer
on top of the vent disc, channel side down, as shown by the image to the right
of this text box.
-
Confirm the vent disk is located on the strut, under the dust boot. If for any reason your vent disk is not pres-ent, please call our technical support staff before proceeding, as driving on the strut without it could cause the shock to fail.
-
Loosen the set screw on the spring perch.
-
Using the provided spanner wrench, turn the bottom spring perch to obtain desired spring perch height, measuring from the top of the perch to the center of the bushing. Find the appropriate spring perch height by referencing the tables above. We do not recommend adjusting outside of the specified height range, as the performance of the shock may decrease greatly. Your vehicle’s exact ride heights may vary due to differences in chassis and trim levels. The perch heights depicted on our tables are a suggested starting point.
-
Tighten the set screw.
-
Place the Belltech upper spring seat onto the OE top mount.
Belltech Coilover Height Setup and assembly Continued -
Assemble the helper spring, intermediate ring, main spring, upper spring seat and OE top mount onto the Belltech coilover.
-
Torque the supplied nylock nut onto the strut. Reference the OE strut markings and ensure the top mount is oriented in the same fashion it was before disassembly.
Coilover installation -
Install the top mount into the chassis and secure using the OE nuts. Torque the nuts to factory specifications.
-
Replace the two brake line bolts and the one lower control arm bolt attaching the control arm to the spindle.
-
Reattach the bolt holing the lower strut to the lower control arm.
Finalizing the Installation -
Re-install the wheels and tighten the lug nuts.
-
Lift the vehicle and remove the support stands.
-
Carefully lower the vehicle onto the flat ground.
-
Torque the lug nuts to manufacturer’s specifications.
-
Check that all components and fasteners have been properly installed and torqued.
-
Re-read and perform all tasks in the “Before Driving Your Vehicle” section of page 1 of your instructions.
Thank you for choosing Belltech.
You are now a part of the Belltech family and we are eager to catch a glimpse
of your newly modified vehicle. Give us a shout out and let us know how much
you love our product. Don’t forget, we offer other Belltech related
merchandise for you and your vehicle on our website,
www.belltech.com!
belltechsuspension
Belltech Suspension
@belltechsuspension
If you have any questions, concerns, or warranty related issues regarding your Belltech product, please call or email our experienced customer service specialists.
Belltech Customer Support:
Phone: 1-800-445-3767 Email:
info@belltech.com
KIT CONTENTS
15213
Part number| Description| Qty
15213-100| Belltech Coilover| 2
68510039| Spanner Wrench| 1
15213-100
Part number| Description| Qty
15213-245| Threaded Damper| 1
65210800| Dust Boot| 1
15002105| Vent Disc| 1
65210799| Bump Stop| 1
4935-001| 15mm Packer| 1
15000-003| Intermediate Ring| 1
4001-001| Helper Spring| 1
68320103| Set Screw M5x12| 1
15103-103| Upper Spring Adapter| 1
70110-330-993| Linear Spring| 1
65050018| Spring Perch| 1
15213-888 1/20/2022 AP REVA-01
A Division of KW AUTOMOTIVE North America, Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>