Desisti AUREA White Light Instruction Manual
- June 13, 2024
- Desisti
Table of Contents
AUREA White Light
Instruction Manual
INTRODUCTION
Congratulations on your purchase of AUREA Vari White lighting fixture.
AUREA is a high power, highly efficient spotlight using DE SISTI modular PCB
boards system with a total of 2472 LEDs combined with 618 Narrow Spot lenses.
The Lighting Fixture is DMX Controlled and includes a number of parameters
that can be set locally, it is equipped with DSE-2000 a detachable power
supply for AC universal feed 90/240V 50/60Hz that can be remoted up to 50m and
feature variable CCT from Tungsten to Daylight with high power and high CRI.
POWER AND DMX DAISY CHAIN
THE MUSES OF LIGHT – AUREA permits both POWER and DMX DAISY CHAIN.
Each Fixture is respectively equipped with:
For DMX: XLR5 pin Panel Mount Male (DMX IN)
1 XLR5 pin Panel Mount Female (DMX OUT)
For Mains Supply: 1 32A Powercon TRUE 1 TOP (POWER IN)
It is recommended to Daisy Chain a Max of 10 fixtures, even if the limitations
imposed by DMX Standards are for an higher q.ty of units.
CHARACTERISTICS AND PERFORMANCE DATA
DESCRIPTION | VALUE | DESCRIPTION | VALUE |
---|---|---|---|
LED Power | 1990 W | Protection Type | IP23 — rain protected |
Power Consumption | 2040W @ 230V 12040W @120V | Max Housing temperature | 10° C |
DMX Data Link USITT DMX512-A | This product uses DMX input and shielded data |
cables. load the daisy chain.
mum of 32 devices a single| a 5-pin XLR for output. Use a
Do not over- Up to a maxi-
can be used on DMX chain.| Weight of Fixture| Head| Driver
88 Kg| 13 Kg
WAX Channels| DMX Channels:
Dimmer / Light Intensity 8 BIT 2 channels Base:
Dimmer Base +1: CCT Control| DMX Channels: Dimmer / Light Intensity 16 BIT
3 channels Base: Dimmer Gross Base +1: Dimmer Fine
Base+2: CCT Control| | |
|
Protection class| Class 1- ground connection required| | |
|
Emitting Surface diameter| 1500 mm. / 59″| | |
|
SAFETY INSTRUCTIONS
Professional use: This luminaire has been designed for professional use and
must be operated by qualified personnel only. Not for residential use.
Grounding:
WARNING: THIS LUMINAIRE MUST BE GROUNDED
WARNING: Disconnect Power CORDS before any maintenance work or opening
the FUSE HOLDER. RISK OF SERIOUS INJURY.
Electrical connections: IMPORTANT The cores in this mains lead are colored in
accordance with the following code:
| Europe| America
---|---|---
Ground| Green & yellow| Green or green & yellow
Neutral| Blue| White
Live| Brown| Black
In case the colors of the cores do not correspond to the colors of the connection points on your plug, please proceed as follows:
- the green or green and yellow core must be connected to the connection point marked with the letter E or with the symbol or colored in green or in green – yellow;
- the blue (or white) core must be connected to the connection point marked with the letter N or colored in black;
- the brown (or black) core must be connected to the connection point marked with the letter L or colored in red.
Working conditions
Working Position | Lighting fixture: max. tilting ±90° from horizontal |
---|---|
Ambient temperature, to at the place of installation and storage | Minimum |
10°C, maximum +40°C
Humidity at the| place of installation and storage| 25-80% (not condensing)
Minimum distances from inflammable surfaces| Top| | Back| Sides| Front
0,4 m.| 0,3 m.| 0,3 m.| 1,5 m.
The luminaire should never be OPERATED close to inflammable materials. The
ones indicated in the above table are the minimum distances recommended. Other
requirements for safe use are: A. Do not cover the apertures of the detachable
driver housing. They are essential for correct ventilation B. Use only
original accessories and spares from De Sista Lighting.
C. Before hanging the luminaire ensure that the suspension point (or the
stand) is properly rated to accept the luminaire weight.
D. A suitable secondary safety suspension device (safety cable, chain or
equivalent) must be fitted between the suspension point and the eyelet at the
front of the body.
WARNING :
- DO NOT MOUNT THE LUMINAIRE ON A NORMALLY FLAMMABLE SURFACE.
- USE OF SANDBAGS AND TIE-ROD/PUSH-ROD IS MANDATORY (EXTERNAL USE).
- EXPOSED DATA ARE INTENDED WITH A COSTANT WIND FLOW. PLEASE CONSIDER SUDDEN GUSTS OF WIND AND USE FURTHER PRECAUTIONS.
INSTALLATION INSTRUCTIONS
The following procedure should be adopted: Before connecting the luminaire to
the electrical mains ensure that:
A. Earth line is present on the power socket.
B. The mains voltage is within the rated range of the luminaire (see technical
data on the rating label)
C. The front safety shield is present and in good condition. It consists of a
Fresnel lens made by borosilicate un-toughened glass, with a Diameter = 150 mm
, thickness = 5 mm type ( 3min)
WARNINGS :
- Do not operate the product if the ambient temperature exceeds 40° C
- Provide a minimum clearance of 0,1m (4 in.) around driver fans and head heatsink.
- Shields, lenses safety or dichroic glasses shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
- The luminaire shall only be used complete with its protective shield
D. Applying power: never connect to dimmer power. Install a power plug on the power cable using the following pin assignment:
- : Neutral
- : Live Green/Yellow : Ground – This fixture must be connected to ground. Make sure the local power voltage is within the range specified. If so; connect the power cable and turn the power on.
E. Stand Alone operation:
Using the navigation buttons and display readout ( refer to the “Local Menu” chapter )navigate to Manual and set the desired intensity (for additional operations see “Local Menu” chapter) DMX operation:
Connect DMX cable. Navigate to Address mode (Addr) and set the desired address, (refer to the “Local Menu” chapter). Connect to DMX controller (refer to the “Channel Setting” in the “Local Menu” chapter) and Use it.
IMPORTANT: Utilize only the safety PIN provided with the unit!
LOCAL MENU
THE MUSES OF LIGHT – AUREA has a GRAPHIC DISPLAY backlit, with a local knob, having a push/click function in addition to the rotation, and 7 control buttons:
Display
It is a Graphic, backlit LCD Display. It contains all the relevant information
for the product setup and performances, such as CCT, DMX Address, DMX Level,
LED Temperature and local dimming. When the local knobs are not used for more
than 10 seconds the display back illumination will go OFF and the display
itself will go in STAND BY Mode. It will go ON again anytime the KNOB is
activated or a button is pushed. Knob
It allow to regulate both DIMMING and CCT Variation. Pushing it the display
will switch from DIMMING to CCT CONTROL By rotating it clockwise the DIMMING
increase from 0% to 100% while the CCT Changes from 2.750°K up to 6.900 °K.
Knob recognizes the speed rotation so to increase the operation speed
accordingly. Button 1
It is the MENU button. When pushed it will allow to enter into the device
MENU. If pushed from inside a MENU Voice will exit from that. If pressed into
the menu will exit to the info menu and when pushed again come back to Home
display.
Button 2
It is the SWITCH MODE button and MENU CONFIRMATION. If pushed from the Home
Display it will switch from latest DMX values memory to Manual DIMMING and
manual CCT. If pushed from inside a MENU Voice will CONFIRM THE SELECTION.
Button 3
It is the RF (LUMENRADIO) MODE ON/OFF button and MENU UP ARROW. With a LONG
PRESS (3sec) from the Home Display it will TURNS ON/OFF the W-DMX LUMENRADIO
MODULE. If pushed from inside THE MENU AND MENU VOICE will work as UP ARROW.
Button 4
It is the RF (LUMENRADIO) UNLINK button and MENU DOWN ARROW.
With a LONG PRESS (3sec) from the Home Display it will UNLINK the W-DMX
LUMENRADIO MODULE from the SENDER. If pushed from inside THE MENU AND MENU
VOICE will work as DOWN ARROW. Button SET 1
When in Storaro Mode it will set the CCT to 5600K. In De Sista mode with long
press it will memorize the current DIMMING and CCT values in SET 1 and once
pushed it will recall the setting
Button SET 2
When in Storaro Mode it will set the CCT to 4300K. In De Sisti mode with long
press it will memorize the current DIMMING and CCT values in SET 2 and once
pushed it will recall the setting
Button SET 3
When in Storaro Mode it will set the CCT to 3200K. In De Sisti mode with long
press it will memorize the current DIMMING and CCT values in SET 3 and once
pushed it will recall it Micro USB Port
Connected to a Windows PC with the proper DeSisti software installed it1 will
allow Firmware upgrades once released. The following are the BASIC FUNCTIONS
and COMMANDS that are provided on the LOCAL MENU ofthe LED DEVICE. The unit is
provided with a USER MENU accessible instantly on the product.
DE SISTI MUSES OF LIGHT – 8 bit.
DE SISTI MODE
8BIT – VARI-WHITE|
channel| value| percent| function
CH BASE| 0-255| 0-100%| MASTER DIM
CH BASE + 1| 0-255| 0-100%| CCT CONTROL
DE SISTI THE MUSES OF LIGHT – 16 bit.
DE SISTI MODE
16BIT – VARI-WHITE|
channel| value| percent| function
CH BASE| 0-255| 0-100%| MASTER DIM
CH BASE 1| 0-255| 0-100%| FINE DIM
CH BASE 2| 0-255| 0-100%| CCT CONTROL
DE SISTI THE MUSES OF LIGHT – 8 bit.
STORARO MODE
|
8BIT – VARI-WHITE
channel| value percent function
CH BASE| 0-255 0-100% MASTER DIM
CCT Control through local (display)
DE SISTI THE MUSES OF LIGHT – 16 bit.
STORARO MODE. CHART
16BIT – VARI-WHITE|
channel| value percent function
CH BASE| 0-255 0-100% MASTER DIM
CH BASE + 1| 0-255 0-100% FINE DIM
CCT Control through local (display)
Basic functions:
Menu and settings Enter, Navigate and Exit the Menu
DMX CHART
The unit occupies 2 channels in 8bit mode an 3 channels in 16bit mode.
To enter the Menu push the Button 1 then push the Button 2 to activate the
navigation. To move into the menu voices push Button 3 and 4 as Up & Down To
enter a Menu Voice push the Button 2 and then move into the settings with
Buttons 3 and 4. To confirm the desired setting push the Button 2. To cancel
and not save the setting into themenu voice push Button 1.
To exit the Menu push button 1, at fortress the unit it will show an Info
Screens owing FW version, Fan speed and LED and Driver(s) temperature.
Change DMX address
To change the unit DMX address navigate into the menu until you reach the
voice “DMX Address”
Push Button 2 to enter the menu voice and Button 3 and 4 to reach the desired
address. To confirm push button 2. Activate Storrow mode or De Sista mode
To change the unit Mode navigate into the menu until you reach the voice
“Mode Sel.” Push Button 2 to enter the menu voice and Button 3 and 4 to select
the desired mode.
To confirm push button 2. Storaro Mode:
In this mode you can work as the Master prefers to work on the set.
DMX channels will be only for dimming while CCT tuning it will be allowed
only manually on the driver.
The 3 “SET” buttons will be activated with 3 preset color temperatures:
| SET 1: 5600K
---|---
| SET 2: 4300K
0| SET 3: 3200K
De Sisti Mode:
In this mode the unit will work with Dimming and CCT active on DMX. The 3 set
buttons will allow to save a dimming and CCT configuration to recall it later.
Backlight
To change the display backlight settings navigate into the menu until you
reach the voice “Backlight” Push Button 2 to enter the menu voice and Button 3
and 4 to reach the desired value. To confirm push button 2.
- Backlight=On:
- The display light will be always ON
- Backlight= Off: The display light will switch
- OFF after 10 seconds without any user command.
Change the DMX Dimming resolution
To change the DMX dimming from 8bit to 16 bit navigate into the menu until you
reach the voice “DMX Bit”. Change the Dimming Curve mode Push Button 2 to
enter the menu voice and Button 3 and 4 to reach the desired value. To confirm
push button 2.
Change the Dimming Curve
To change the Dimming Curve between HR Dim (over 40.000 dimming points,
super smooth) and Linear, navigate into the menu until you reach the voice
“Dim Curve”.
Push Button 2 to enter the menu voice and Button 3 and 4 to reach the desired
value. To confirm push button 2. Change the Dimming Speed
To change the Dimming Speedo change the device reaction while dimming with
the possibility to choose between Fast andosols (factory setting: slow)
reaction, navigate into the menu until you reach the voice “Dim Speed”.
Push Button 2 to enter the menu voice and Button 3 and 4 to reach the desired
value. To confirm push button 2. Activate Bridge Mode
To activate the Bridge Mode, navigate into the menu until youreach the
voice “Bridge Mode”.
Push Button 2 to enter the menu voice and Button 3 and 4 to reach the desired
value. To confirm pushbutton 2. Bridge Mode allow to utilize the unit to
spread to other devices the DMX signal received with the wireless module
through the DMXOUT cable plus. Activate the wireless DMX module
To switch on or off the Wireless Module, navigate into the menu until you
reach the voice “Wireless”. (The module can be activated also from the Main
screen: look at the following related section).
Push Button 2 to enter the menu voice and Button 3 and 4to reach the desired
value. To confirm push button 2. Local Manual Mode
When no Wired (WR DMX in the unit display) or Wireless connection (RF DMX in
the unit display) is active the unit can be controlled in Manual mode.
Dimming
Enter the Menu To set the dimming value rotate the encoder knob until you
reach the desired dimming level If the display is showing the CCTvalue you’ll
need to push the Knob to switch to the dimming(the display will write
Man.Dimming” and will show a percentage value). CCT Tuning from 2700°K to
6500°K
To set the dimming value rotate the encoder knob until you reach the
desired CCT level. If the display is showing the Dimming value you’ll need to
push the Knob to switch to the dimming(the display will write “Man. CCT” and
will show a percentage value). Switch from Manual to DMX Mode (If no
connection is present the unit will recall the latest DMX setting)
To switch from latest DMX value to Manual settings push the Button 2 .
Turn on RF Module (Wireless DMX)
To turn on the RF Module to connect to a Wireless DMX Sender keep pushed
the Button 3 for 3 seconds. The RF ON Green LED indicator will turn on and
after few seconds also the LINK LED indicator will turn on.
The unit will automatically pair with the nearest sender active. PLEASE
NOTE: the RF module must be unpaired from the previous sender once need to
change the DMX sender device.
Unpairing the RF Module (Wireless DMX)
To unpair the RF Module from the previous connected Wireless DMX Sender
keep pushed the Button 4 for 3 seconds.
The LINK Green LED indicator will turn off.
After this pushing the pairing button from a sender the unit will
automatically reconnect to a new DMX sender. Recall preset CCTs in Storrow
mode or save and recall customized CCT and dimming in De Sisti mode
When the unit is in “Storaro mode” pushing the button SET 1, SET2 and SET 3
will recall 3 preset color temperatures: SET 1: 5600K
SET 2: 4300K
0 SET 3: 3200K The user then will be allowed to tune the CCT from the
“preset value” and the related indicator LED will turn off once the CCT value
will change from the preset.
Important: in Storaro mode the CCT can be changed only manually, no DMX
channel is activated for CCT tuning.
When in “De Sisti mode” the same buttons can be used to save the current
dimming and CCT level to recall it later. To save the desired values push the
related SET 1, SET 2 or SET 3 button for 3 seconds. To recall it simply push
the related button.
FIRMWARE UPGRADE
To upgrade the Firmware connect the unit MICRO USB port to a Microsoft Windows
PC with the Desist upgrade software installed. To install the software:
Unpack the ZIP file provided by your local reseller or the De Sisti website.
You will unpack:
- DRIVER USB
- BOOTLOADER
Install the USB drivers entering the proper folder and launching the .exe
inside it.
Then enter the BOOTLOADER folder and launch the exe Bootloader DeSisti Vx.x.
Then follow these STEPS:
- With unit connected through USB push Find Device.
- The software will show the USB connected COM Port.
- Push “Connect CPU”.
- The unit and the display will enter into boot mode.
- Push “Load Hex file.
- Enter the folder where you have previously saved the CPU Firmware file and open it. WARNING: The file name MUST Start with “CPU_xxxxx”.
- Software will show the log “Hexfile loaded successfully.
- Push the button “Erase-Program Verify.
- Software will start to erase the old firmware and upload the new one, then will check the FW integrity.
- Once done push Run Application.
- The software will disconnect the unit that will turn to operative mode with the new FW installed.
IMPORTANT: Don’t push the Buttons “Connect DRV1 DRV2 DRV3 and DRV4”. These are needed when De Sisti releases also new DRV FWs for massive changes. The procedure to upload the FW is the same than the CPU one but, as it’s possible to DAMAGE the unit DRIVER it must be done by or with the support of a qualified DE SISTI assistant person.
DIMENSIONS
PERIODIC INSPECTION & MAINTENANCE
This product requires very little routine maintenance, if any, but has special
cleaning instructions:
Disconnect fixture from power and allow it to cool for 10 min.
- Vacuum or gently blow away any dust from fan blades and grills
- Very gently clean the LED with Isopropyl alcohol.
- Clean the lenses with a soft damp cloth.
- Check the condition of the safety shield (see chapter: Installation Instructions) before every use.
- Check Power supply cable and DMX control cable proper conditions
SAFETY STANDARDS
Europe: The product conforms the Applicable European Directives &
Standards
Low Voltage Directive: 73/23/EEC (as amended by 93/68/EEC)
EMC Directive: 89/336/EEC (as amended by 92/31/EEC & by 93/68/EEC)
Europen Standards:: EN 60598-2-17, EN 60598-1 , EN 55015 , EN 61547
Disposing of this product:
Help preserve the environment! Ensure that this product is recycled at the end
of its life.
This product is in compliance with the RoHS and WEEE directives.
This Manual is applicable to the De Sisti – Storaro The Muses of Light –
AUREA
Revised on March 2021ILT ITALY srl
Via Cancelliera, 10/a
00041 Albano Laziale (Rome) Italy
tel. +39 06-902901 fax +39 06-90231051
www.desisti.it
Documents / Resources
|
Desisti AUREA White
Light
[pdf] Instruction Manual
AUREA, AUREA White Light, White Light, Light
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>