FEITIAN F210 Smart Financial Terminal Instruction Manual
- June 13, 2024
- Feitian
Table of Contents
F210 Smart Financial Terminal
Instruction Manual
F210 Smart Financial Terminal
Product configuration
Installation
Open battery lock, put in battery, close battery lock.
When installing the battery, please pay attention to the battery metal contact
part in alignment with the battery contactor on the terminal. Then press the
battery lightly.
Install printing paper, gently press both sides of the paper bin, open the
printer lid and put the printing paper in. Please pay attention to printing
paper direction.
Safety warning
Do not contact the terminal and its accessories with liquid or wet
environment.
Do not put the terminal in an environment where the temperature is too high or
too low.
Do not put the terminal into the fire. Do not disassemble the terminal or any
of its accessories.
After-sales service In case of any terminal failure, please contact after-
sales service through sales-supportl@ftsafe.com
FCC Statement
Any Changes or modifications not expressly approved by the party responsible e for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information (SAR) :
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
The exposure standard for wireless devices employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6
W/kg. *Tests for SAR are conducted using standard operating positions accepted
by the FCC with the device transmitting at its highest certified power level
in all tested frequency bands.
Although the SAR is determined at the highest certified power level, the
actual SAR level of the device while operating can be well below the maximum
value. This is because the device is designed to operate at multiple power
levels so as to use only the poser required to reach the network. In general,
the closer you are to a wireless base station antenna, the lower the power
output. The highest SAR value for the device as reported to the FCC when worn
on the body, as described in this user guide, is 1.04W/kg (Body-worn
measurements differ among devices, depending upon available enhancements and
FCC requirements.)
The highest SAR value for the device as reported to the FCC when worn on the
handheld, as described in this user guide, is 1.15W/kg While there may be
differences between the SAR levels of various devices and at various
positions, they all meet the government requirement. The FCC has granted an
Equipment Authorization for this device with all reported SAR levels evaluated
as in compliance with the FCC RF exposure guidelines. SAR information on this
device is on
file with the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on
FCC ID: ZD3FTF210
For body worn operation, this device has been tested and meets the FCC RF
exposure guidelines for use with an accessory that contains no metal and the
positions the device minimum of 0 mm from the body . Use of other enhancements
may not ensure compliance with FCC RF exposure guidelines. If you do not use a
body-worn accessory position the device a minimum of 0 mm from your body when
the device is switched on at its highest certified power level in all tested
frequency bands.
FEITIAN Technologies Co., Ltd (Stock Code: 300386)
Email: sales-supportl@ftsafe.com 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>