ROAD ARMOR 617XEFXB Evolution Front Bumper Instruction Manual
- June 13, 2024
- ROAD ARMOR
Table of Contents
617XEFXB Evolution Front Bumper
Instruction Manual
617XEFXB Evolution Front Bumper
INSTALL INSTRUCTIONS
Evolution Front Bumper
Product : 617XEFXB
Application : 2017+ Ford Super Duty
WARNING
Read the instructions completely before beginning installation. Before tightening bolts, drilling or cutting where required, check to make sure there are no obstructions such as brake, fuel or electrical lines which may be damaged. Also keep in mind this is an aftermarket product and MAY require minor shimming and/or trimming, reaming, etc. for proper fit. Road Armor is not responsible for any damages to vehicle.
IMPORTANT NOTICE
- Be sure to inspect and test fit your product to ensure proper fitment before having it coated, painted, bed lined, etc.
- Road Armor will not be responsible for the cost of coating your unit if any problems with fit or finish are not noted and addressed beforehand.
SAFETY FIRST!
- FOLLOW ALL INSTRUCTIONS, YOUR SAFETY AND THE SAFETY OF OTHERS IS MOST IMPORTAN
- WEAR APPROPRIATE EYE PROTECTION AND EXERCISE CAUTION WHEN DRILLING / CUTTING
REQUIRED TOOLS
SAE & METRIC Socket set and wrenches
Screw drivers, pry tool, pick tool, pliers
REQUIRED TOOLS
SAE & METRIC Socket set and wrenches
Screw drivers, pry tool, pick tool, pliers
INCLUDED HARDWARE
2 1/2″ Bolt 15/16″ O.D. Zinc Pushnut Bolt Retainer
8 1.5″ Single Bolt Tab (ZINC)
4 1/4″-20 Zinc Finish Grade A Finished Hex Nut
8 1/2″-13 x 1-3/4″ Grade 8 Yellow Zinc Finish Hex Cap Screw
24 1/2″ x 1.375″ OD Thru-Hardened Yellow Zinc Finish Steel USS General Purpose
Flat Washer
16 1/2″ Yellow Zinc Finish High Alloy Medium Split Lock Washer
16 1/2″-13 Yellow Zinc Finish Grade 8 Finished Hex Nut
4 #10-24 Zinc Finish Steel with External Tooth Lock washer K-Lock Nut
3 5/16″-18 x 3/4″ ASTM F593 18-8 Stainless Steel Hex Cap Screw
8 Regular FW 0.25
22 SBHCSCREW 0.1924×0.5-HX-N
4 SBHCSCREW 0.2520×0.75-HX-N
2 Road Armor 8″ Accent Light
**NOTE: 2020+ Super Duty with Adaptive Cruise will Require 620ACM Adapter Kit**
- Disconnect bumper harness & block warmer (if equipped) . These plugs are located behind the bumper near the frame on the Passenger side.
- Remove plastic trim around tow hooks to reveal bolts on both Driver and Passenger sides.
- Remove inner bumper support bolts. This is a truss like support bracket located near the first body mount behind the bumper.
- Remove plastic cover over adaptive cruise control module (if equipped)
- Unbolt, unplug and carefully set aside the Adaptive Cruise Control Module (if equipped). 620ACM Adapter Provided for 2020+ Super Duty’s
- Remove 4 bolts each side of tow hooks and pull off factory bumper.
- Remove tow hooks both sides
- Remove under-run guards and set aside hardware for later use. These double bolt plates and nuts will be used to attach the Road Armor brackets.
- Install brackets over frame as shown
- Re-install factory double bolt plates through frame and bracket
- Install the half inch bolts using washers on both sides then lock washer and nut. Do not fully tighten.
- Install one of the single bolt tabs through top inside bumper slot and affix using supplied retainer clips. These are installed by pushing on with a deep socket while holding the back.
- Install ACM if equipped. Install wiring harness
- Install winch and accent lights
- Fit up the bumper, carefully aligning retained bolts with corresponding bracket slots. For fully guarded units tape off areas where tube may make contact with the vehicle.
www.ROADARMOR.com
2017 + Ford Super Duty
(V.20161220)
Documents / Resources
| ROAD
ARMOR 617XEFXB Evolution Front
Bumper
[pdf] Instruction Manual
617XEFXB Evolution Front Bumper, 617XEFXB, Evolution Front Bumper, Front
Bumper, Bumper
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>