Perimeter Billiard Lights V60-1 Modern LED Billiard Pool Table Light Instruction Manual

Perimeter Billiard Lights V60-1 Modern LED Billiard Pool Table Light

Product Information

The Perimeter Billiard Lights are LED lights designed specifically for billiard tables. They come in three different sizes: 7ft, 8ft, and 9ft.

The dimensions of each size are as follows:

• 7ft LED light: 82.7″ long
• 8ft LED light: 93.7″ long
• 9ft LED light: 102.4″ long

The LED panel on each light has a width of 2.75″ and a height of 2.4″.

The wattage and luminosity specifications for each size are:

• 7ft LED light: 160w, 13,800lm
• 8ft LED light: 180w, 15,500lm
• 9ft LED light: 200w, 17,000lm

Product Usage Instructions

1. Locate sturdy ceiling joists above the table rails on each long side.
2. If there are no available sturdy joists, use part F as a drywall anchor.
3. Attach part J to the ceiling using screw E.
4. Adjust the length by pushing the small button and leave a small gap when screwing.
5. Repeat steps 1 to 5 for up to 8 suspension cables, with 4 on each long side.
6. Connect the suspension cable from step 3 to the ceiling.
7. Prepare to attach the 6 sections of LED light to the suspension cables, following the diagram on page 3.
8. Slide the end of the suspension cables into the top of the LED light, starting with the two long sides.
9. Connect each joint using part A and part D.
10. Connect the two short sides to the long side using part B (x2), part C (x1), and part D.
11. Adjust the final height using a level tool. Recommended light height is 75-90 inches from the floor or 45-60 inches from the table cloth.
12. Wire each LED light section using the electrical cable (part L) in the order of number 1 to 6, following the anti-clockwise direction.
13. Once all 6 sections are connected, place the electrical cable inside the frame to hide it from view.
14. Use black tape to cover all the joints and block any visible seams.
15. If your model is non-dimmable, you can either plug the light into an outlet or hardwire it with a wall switch. If using the plug, consider getting a remote outlet for convenient on/off control.
16. If your model is dimmable, you can either plug the light into an outlet or hardwire it. The dimming function can only be controlled using the included remote.
17. To pair the remote with the light, press the SETUP button 3 times within 5 seconds after powering on. The light will flash twice to indicate successful pairing.
18. The remote allows you to turn the light on/off, adjust brightness, switch between half/full brightness, activate dark mode, and set a delayed turn-off.

Please contact sales@perimeterbilliardlights.com if you have any further questions.

Dimension

Parts

Step 1

Step 2

Don’t fully screw, leave a small gap

Step 3

• Suggest light height: 75-90 inches from the floor.

Step 4

Locate (4) sturdy ceiling joists over each LONG side, right above table rails, then use screw E attach Part J to the ceiling. *Use part F as drywall anchor if there is no available sturdy joist.

Step 5

Connect suspension cable from step 3 to the ceiling.

Step 6
Repeat step 1 to step 5 up to 8 suspension cables. Final result should look like below.

Step 8

Slide the end of suspension cables into the top of light.

• Install two long sides first.

Step 10

Once finished attaching two long sides to the suspenson cables, use part Ax3 and part D to cennect each joint.

Step 11

Once finished two Long sides, connect two short sides to the long side. Use part Bx2, Cx1, and D to connect each joint on the corner.

Step 12

Adjust final height by using level tool. Recommend light height is 75-90 inchs from floor, or 45-60 inches from the table cloth.

Step 13

Use the electrical cable (part L) to wire each LED light, in the order of number 1 to 6 with ANTI-CLOCK direction. (make sure align connector)

Step 14
Once all 6 sections are connected, place the electrical cable nicely inside the frame to make sure it is not visible from the side.

Step 15

Use black tape nicely cover all the joints to block visible seams.

Step 16

For non-dimmable model:
You can either plug the light into an outlet, or remove the 2-pin plug to hardwire it with a wall switch. If you are going to use the plug, and don’t have a switch for the outlet, we highly recommend to get a remote outlet to turn on/off the light.

• The light can not be compatible with a dimmer switch.

For dimmable light, please check Step 17.

Step 17
For dimmable model:
You can either plug the light into an outlet or hardwire it.

• The light can NOT be compatible with a dimmer switch. It can only be dimmed with the remote.

Pair the remote with light:
After powering on, quickly press “SETUP” button 3 times within 5 seconds, then the light will flash twice, which means paired successfully.

Please contact us at sales@perimeterbilliardlights.com for any questions.

References

• Professional LED Billiard Pool Table Light | Perimeter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>