Perimeter Billiard Lights V60 LED Pool Table Light Instruction Manual

Perimeter Billiard Lights V60 LED Pool Table Light

Perimeter Billiard Lights Instruction Manual

www.PerimeterBilliardLights.com

Product Information

17,000lm
8ft LED light| LED panel width 2.75”, height 2.4”, watt 180w, lumin
15,500lm
7ft LED light| LED panel width 2.75”, height 2.4”, watt 160w, lumin
13,800lm

Product Usage Instructions

• Step 1: Locate (4) sturdy ceiling joists over each LONG side, right above table rails.
• Step 2: Use screw E to attach Part J to the ceiling. Use part F as a drywall anchor if there is no available sturdy joist. Don’t fully screw, leave a small gap.
• Step 3: Adjust the length by pushing the small button on the suspension cables. *Suggest light height: 75-90 inches from the floor.
• Step 4: Repeat step 1 to step 3 for up to 8 suspension cables. Connect the suspension cable from step 3 to the ceiling.
• Step 5: Prepare to attach 6 sections of LED light to suspension cables. Place number 1 and 6 on the same side, 3 and 4 on the other side. Place number 2 & 5 as shown in the picture.
• Step 6: Slide the end of suspension cables into the top of the light. Install two long sides first.
• Step 7: Once finished attaching two long sides to the suspension cables, use part A x 3 and part D to connect each joint.
• Step 8: Once finished with two long sides, connect two short sides to the long side. Use part B x 2, C x 1, and D to connect each joint on the corner. Adjust the final height by using a level tool. Recommend light height is 75-90 inches from the floor or 45-60 inches from the table cloth.
• Step 9: Use the electrical cable (part L) to wire each LED light, in the order of number 1 to 6 with ANTI-CLOCK direction. Make sure to align the connectors.
• Step 10: Once all 6 sections are connected, place the electrical cable nicely inside the frame to make sure it is not visible from the side.
• Step 11: Use black tape to nicely cover all the joints to block visible seams.
• Step 12: For the non-dimmable model: You can either plug the light into an outlet or remove the 2-pin plug to hardwire it with a wall switch. If you are going to use the plug and don’t have a switch for the outlet, we highly recommend getting a remote outlet to turn on/off the light. For dimmable light, please check Step 17.
• Step 13: For dimmable model: You can either plug the light into an outlet or hardwire it. Pair the remote with light: After power on, press SETUP button 3 times in 5 seconds. The light will flash twice, which means paired successfully.
• Step 14: Turn on, Brighten (up), Dim (down), Turn off, SETUP (pair), Half / full brightness, Dark mode, Delayed turn-off, automatic turn-off light after 1 minute. *(4) NULL buttons are not functional.

Dimension

Parts

Step 1

Step 2
Don’t fully screw, leave a small gap

Step 3
Suggest light height: 75-90 inches from the floor

Step 4
Locate (4) sturdy ceiling joists over each LONG side, right above table rails, then use screw E attach Part J to the ceiling. Use part F as drywall anchor if there is no available sturdy joist. no available sturdy joist.

Step 5
Connect suspension cable from step 3 to the ceiling.

Step 6
Total 8 suspension cables, 4 on each long side Repeat step 1 to step 5 up to 8 suspension cables. Final result should look like below

Step 7
Total 8 suspension cables, 4 on each long side

Step 8

Step 9
Slide the end of suspension cables into the top of light. Install two long sides first.

Step 10
Once finished attaching two long sides to the suspenson cables, use part Ax3 and part D to cennect each joint.

Step 11
Once finished two Long sides, connect two short sides to the long side. Use part Bx2, Cx1, and D to connect each joint on the corner.

Step 12
Adjust final height by using level tool. Recommend light height is 75-90 inchs from floor, or 45-60 inches from the table cloth.

Step 13
Use the electrical cable (part L) to wire each LED light, in the order of number 1 to 6 with ANTI-CLOCK direction.make sure align connector

Step 14
Once all 6 sections are connected, place the electrical cable nicely insidethe frame to make sure it is not visible from the side. the frame to make sure it is not visible from the side

Step 15
Use black tape nicely cover all the joints to block visible seams.

Step 16

For non-dimmable model
You can either plug the light into an outlet, or remove the 2-pin plug to hardwire it with a wall switch.  If you are going to use the plug, and don’t have a switch for the outlet, we highly recommend to get a remote outlet to turn on/off the light.

For dimmable light, please check Step 17.

Step 17

For dimmable model
You can either plug the light into an outlet or hardwire it.

Pair the remote with light
After power on, press “SETUP” button 3 times in 5 secends, the light will flash twice, which means paired successfully.

References

• Professional LED Billiard Pool Table Light | Perimeter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>