WaveBird Y-D002 2.4GHz NGC Wireless Controller User Guide

WaveBird Y-D002 2.4GHz NGC Wireless Controller

Product Information

Product Usage Instructions

To use Product X correctly and safely, please follow the instructions below:

1. Ensure that the product is placed on a stable and flat surface.
2. Connect the power cable to the designated power outlet.
3. The product features an on/off switch located on the side panel. Turn it on by toggling the switch to the “ON” position.
4. Wait for the product to initialize. This may take a few seconds.
5. The product is now ready for use. Use the control buttons or remote control (if provided) to navigate and operate the product’s functions.
6. Refer to the user manual for detailed information on how to utilize specific features and settings.
7. When finished using the product, turn off the power switch and disconnect the power cable from the outlet.

For any further assistance or troubleshooting, please refer to the full user manual or contact our customer support.

Pre-Pairing Considerations

1. Ensure the controller is fully charged. (Please ensure your controller is powered on before charging.)
2. For seamless detection, connect the receiver into the USB port prior to powering on your device or launching an emulator. If the controller is not detected during pairing, consider restarting your device.
3. Please be aware that there are slight differences in the pairing steps between PC and Nintendo Switch. When using the controller on a Nintendo Switch, specific additional steps are required. Kindly refer to the User Guide for comprehensive instructions.

LED Indicator Guide

1. Turn On the “Power switch”, and Press the + button to initiate a slow flashing LED 1 light, indicating the controller is powered on. Pressing + again results in the rapid flashing of LED 1, indicating the controller is in pairing mode.
2. The LED 1 light remaining steadily lit signifies successful pairing and connection of the controller.
3. When the controller is paired and in use, a slow, periodic flashing LED (approximately every 2.5 seconds) indicates a low battery and the need for recharging.
4. During charging, LED 1 flashes at a relaxed pace (around 2.5-second intervals), while a solid LED 1 light indicates a full charge, confirming the controller is ready for use.
5. The four LED indicator lights will display the channel of the controller when connected to the SWITCH console, and the other function indicators will jump back to the channel display of the controller after a short period of time.

How to Pair

This operation is applicable to two types of receivers, and the choice between NGC or USB receivers depends on the controller package purchased.

Step 1. Before pairing, please ensure your controller is powered off.

Step 2. Insert the receiver into your device’s port and wait for the LED on the receiver to start flashing.

Step 3. Press and hold the “SYNC” button on the receiver until it fast- blinking.

Step 4. Power on the controller. The LED 1 on the controller will begin flashing.

Step 5. Press the “+” button and wait for LED 1 to remain illuminated, indicating a successful controller connection.

Please Note:
These five steps are intended for use with PC, Mac, and Raspberry Pi.
If using the controller on a Nintendo Switch, follow these additional steps:
Use the original Switch controller to navigate to System Settings >
Controllers and Sensors > Pro Controller Wired Communication > ON.
Ensure that the option is set to “ON”. Then proceed with Step 1,2,3,4,5.

Important Notes:
When switching between different devices, Restart the controller, and toggle the “power switch” off and on once to clear the memory. For example, if you have used the X-input Mode on a PC and are switching to a Nintendo Switch Console, restart the controller, and toggle the “power switch” off and on once first, and then re-pair.

RF exposure statement
This equipment complies with the FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt

RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>