GENERALSCAN R1120 Ring Scanner User Guide

QUICK USER GUIDE
FOR WEARABLE BLUETOOTH SCANNERS

R1120/R152#/R352#/R552#
Ring Scanner / Thumbutton Scanner / Ruglove Scanner

Introduction

This Guide is applicable to all GS Wearable Scanners. For detailed information please refer to this guide.
If there are any further questions, please contact support@generalscan.cloud.

Copyright

GENERALSCAN trademarks are registered in many countries around the world. Generalscan Inc. and/or its subsidiaries, all rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing The material in this manual s subject to change without notice. All software without license shall not be transferred to  others.

Laser Safety

Do not stare into the laser beam or view directly with optical instruments.

Battery Safety

• Do not immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard,
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not use the battery if it is bulging, deformed or damaged.
• To charge the mobile device battery, the battery and charger temperatures must be between +32 °F and +104 °F (0 °C and +40 °C).
• Do not use batteries other than those provided by GENERALSCAN, otherwise we will not be responsible for the consequences.
• Dispose of batteries according to instructions.
• Please follow local regulations to promptly dispose of used rechargeable batteries.

GS R1120 & GS R152# Ring Scanners

GS R1120 & GS R152# Thumbutton Scanners

GS R1120 & GS R152# Ruglove Scanners

Ring Scanner Side View

Ring Scanner Back View

Turn ON/OFF
Turn ON the scanner after pressing and holding scanner’s trigger button for 15 seconds.
Turn OFF the scanner after pressing and holding scanner’s trigger button for 5 seconds.

Ring Scanner Setup – Descriptions

Figure 1 Install the Trigger
Determine whether ring scanner is used on the right or left hand and rotate the trigger assembly accordingly, so that the Trigger is positioned next to the thumb when ring scanner s placed on the index finger. Align one end of the Trigger on ring scanner.

Figure2 Assemble the Trigger
Push the other end down until it snaps into place.

Removing the Trigger
Push the yellow latch in, while lifting the Trigger away from the scanner body.

Note: Al steps are applicable to every GS Ring Scanners.

Ring Scanner Setup

Figure 1

Figure 2

Thumbutton Scanner Side View

Thumbutton Accessories

• Adjustable Metal Wire
• Lanyard

Thumbutton Scanner Setup

Insert the tabs on the Thumbutton into the gaps.

Place the Thumbutton latch into the compartment.

Removing the Thumbutton
Push the yellow latch in, while lifting the Thumbutton away from the scanner body.

Ruglove Top and Back View

Ruglove Scanner Setup

1. Insert the tabs on the Scanner Body into the gaps.
2. Place the Scanner Body latch into the compartment.

Ruglove Trigger Button Setup
Connect the trigger button to Ruglove with USB Type-C, compatible wit Left and Right hand wearing habits.

Removing the Scanner Body
Push the *Scanner Body Release Latch on both sides of the glove body towards the front at the same time.

Battery Setup

Insert the tabs on the battery into the gaps.

Place the battery in the battery compartment

Removing the Battery
To remove the battery, please push the release latch on the back of the scanner to the left, then remove the battery with the tabs on the right and left of the battery.

Battery Charging

Please use the cable packed in the box. Place the battery in the charger as follows. Align end of the battery-(1) on the charger. Pull out the retractor-(2).
Push the other End-(3) into the compartment. Then connect the charger to the computer.

Note: In addition, the scanners can be charged directly with a 5V power source with the USB Type-C cable in the package.

Removing the Battery
Please pull out the retractors on either side of the charger before take the battery out of the compartment.

Optional Accessories

Standard package content

1. Battery
2. Strap
3. USB Type-C Cable
4. Battery Charger

All accessories are compatible with every GS Wearable Scanners.

LED Status

Scanning Techniques

Please aim at the middle of the barcode through the red light when scan the barcode. Please scan properly in accordance with the following diagram. Adjust the scanner angle and distance slowly, at the same time, press the trigger button, make the center red light cover the left to right of the barcode;

GENERALSCAN Applications

GENERALSCAN is always with you with our after-sales team! G-Service, Generalscan Keyboard Pro are mobile applications that assist you after-sales. Scan the QR code below and make full use of the unique service.

| |
---|---|---
https://www.generalscan.com/gservice| https://play.google.com/store/apps/details?id=com.generalscan.icode&hl=tr&gl=US| https://www.generalscan.com/shared-documents/generalscan-keyboard-pro

More Language
This Guide is written in English. Please Scan below barcodes with your phone to get access to other languages.

English
https://www.generalscan.com/shared-documents/quick-user-guide-english

Warranty Information
For Generalscan products warranty information, please visit www.generalscan.com/warranty.

https://www.generalscan.com/warranty

Service Information
If there is any problem of GENERALSCAN barcode scanners, please visit our service page, www.generalscan.com/service.

https://www.generalscan.com/services

QUICK USER GUIDE
FOR WEARABLE BLUETOOTH SCANNERS
Email:Support@generalscan.cloud
©2022 GENERALSCAN All Rig hts reserved.
Version 2.0

Documents / Resources

| GENERALSCAN R1120 Ring Scanner [pdf] User Guide
r5522, r5520, r5521, R1120, R1120 Ring Scanner, Ring Scanner, Scanner
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>