NOA Air Beats Wireless Stereo Speaker User Guide

: June 13, 2024
: NOA

Table of Contents

NOA Air Beats Wireless Stereo Speaker
SPECIFICATION
PACKAGE CONTENT
PRODUCT OVERVIEW
OPERATION
BUTTON INSTRUCTION
LED INSTRUCTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NOA Air Beats Wireless Stereo Speaker

$NOA-Air-Beats-Wireless-Stereo-Speaker-FIG- $2$$

SPECIFICATION

Model No.	Air Beats
Version	4.0
Standard	A2DP.AVRCP
Power	Mid-bass driver, l 7w+ Tweeter, 4w
Total Harmonic Distortion	1%21W
Frequency response	50Hz-20KHz
S/N	80DB

Battery

| Built- i n Rechargeable Li-ion Battery

18650/ 2500 mA/ 7.4V

Aux| 3.Sm m Audio-in Jack
USB-C Input| 2.0A’5V
Charging Time| 4H
Play Time| VOL 50% ~~ 8H

PACKAGE CONTENT

I X NOA Air Beats Speaker
I X 3.5mm Audio Cable
I X User Manual
I X USB-C Charging Cable

PRODUCT OVERVIEW

$NOA-Air-Beats-Wireless-Stereo-Speaker-FIG- $3$$

Power/ Play/ Pause button
Bluetooth button
LED Indicator
Vol -/ Previous button
Vol+/ Next button
Hand strap Hole
USB-C Charging Port
AUX in Port
Reset
Cover

OPERATION

Charging for the first time.
Though the speaker is partially charged at the factory, please make sure that you fully charge it before using RED LED flash on in charging, and off while fully charged. Its fully circle time is around 6 Hours.

Low Battery
RED LED flashing, and speaker volume will be decreased automatically. Please charging.

Power ON/OFF
Press and hold the Power on/off button for 25″ , when you hear prompt tones. It will be on/off. Attention: Power ON/OFF tones are different and easy to recognize.

Pairing

Bring the NOA Air Beats wireless Portable speaker to within 3ft( 1m) of your device.
Press and hold the Power on/off button for 2s’ , then you will hear a prompt tone and the speaker will automatically go into pairing mode with the blue LED flashing.
Bring your device into pairing mode and search for the speaker.
Once the speaker has been located by your device you should see “NOA Air Beats” , simply select the device name to connect. If your device is asking for a PIN or passcode, please enter ” 0000″.
When devices are successfully paired, you will hear a short beep, then the blue LED light will stay on. On some devices, you might have to select ” Use as Audio Device (stereo)” or similar on the device’s audio menu.

Repairing

In order to connect the speaker with your device, please make sure your speaker has entered into pairing mode already.
Make sure the speaker is POWER ON.
Press and hold the BLUE TOOTH button for 3s’, after a ring tone, the speaker has been located by your device, and you can see ” NOA Air Beats”, simply select the device name to connect.
When devices are successfully paired, BLUE RED will stay on in play mode.

NOTE

When bringing the device last connected into pairing mode, the speaker will automatically connect to it
If pairing is not completed within 3 minutes, please turn off the speaker and try again. The speaker will power off automatically if there is no connection for 10 minutes.

TWS Pairing
Note : Before TWS pairing, please make sure that the speakers are not paired with another device

Power on both speakers
Press and hold the Bluetooth button
Wait for few seconds (6-10 seconds)
After 10 seconds the speakers will paird automatically.

RESET
When the speaker has be en crashed in an accident, please make sure it is not in charging. Then use a toothpick or paper clips/ BisonFone, insert the bottom of the 3.5mm AUX in jack, press and hold the Reset button more than 35′, the speaker can be returned normal.