VIVA sanitary UP0775_2 Dual Flush Height Adjustable Syphon Instruction Manual

VIVA sanitary UP0775_2 Dual Flush Height Adjustable Syphon

Product Information

The product is a dual flush, height-adjustable syphon for toilet cisterns. It includes a close couple plate, thread back nut, flush valve, doughnut washer, bolts, wingnuts, height adjustment screw, base volume plugs, C link, top plug, and a suction unit. The flush volumes can be adjusted by removing the volume plugs. The product is manufactured by VIVA Sanitary Units.

Product Usage Instructions

1. Before installation, ensure that chlorine/bleach cleaners or related products are not added to the tank water as they can cause damage and void the warranty.
2. Turn off the water supply before installing or removing toilet cistern parts.
3. Insert the flush valve into the water tank.
4. Slide the closed couple plate over the syphon thread and tighten it to the tank using the washer and nut.
5. Fit the doughnut washer and bolts and secure the cistern to the pan with wingnuts.
6. To adjust the height of the flush valve, twist the height adjustment screw to set it to the desired height.
7. To remove the C link, rotate it until it becomes loose.
8. Slide the stem through the base to access the suction unit.
9. To adjust the flush volumes, remove the volume plugs as per the provided guide.
10. To operate the flush valve, connect the C link to the toilet handle lever arm.
11. For low-level installations, slide the back nut and conical washer over the flush pipe and insert the flush pipe into the base of the flush valve. Secure it with the back nut.
12. To perform a full flush, depress and release the toilet handle lever arm. To perform a half flush, depress and hold the lever arm.
13. Water will internally overflow into the toilet pan when the water level reaches the spillover point. To address this, remove the spring and clip, replace the diaphragm washer, secure the clip, and re-fit the spring.
14. Ensure that the syphon does not pool around the C link when it fills, as this can disable the half-flush mechanism.

For further information or inquiries, please contact VIVA Sanitary Units:

VIVA Sanitary Units
1-2 Capitol Trading Park, Kirkby Bank Road Knowsley Industrial Estate, Liverpool, L33 7SY

• Tel : 0151 546 0531
• Fax : 0151 549 4187
• E-mail: sales@vivasanitary.co.uk

WARNING : We shall not be responsible or liable for any failure of, or damage to, this plumbing product caused by the use of chlorine/bleach cleaners or related products added to the tank water. Use of such products will void the warranty and may result in product failure, possibly causing property damage. Do not over-tighten plastic nuts and always turn off the water supply when installing/removing toilet cistern parts.

Please note: Save this instruction sheet for future reference

IMPORTANT: DO NOT use plumber’s putty to seal this fitting

INSTALLATION INSTRUCTIONS

1. Insert the flush valve into the water tank. Slide close a couple of plates over the syphon thread and tighten to the tank using the washer and nut.
2. Fit the doughnut washer and bolts and secure the cistern to the pan with wingnuts.
3. To adjust the height of the flush valve twist the height adjustment screw and set it to the desired height.
4. The flush volumes can be adjusted by removing the volume plugs. (Please refer to the guide above)
5. To operate the flush valve connect the C link to the toilet handle lever arm.
6. Low-level installation does not require a close couple kit. Slide the back nut and conical washer over the flush pipe insert the flush pipe into the base of the flush valve and secure it with the back nut.

Dual Flush Operation

Operating the dual flush function is easy, when flushing your toilet depress and release for a full flush, and depress and hold for a half flush. This will only flush half the water in your tank. Saving water and money.

Internal Overflow
Water will internally overflow into the toilet pan when the water level reaches the spillover point.

TROUBLESHOOTING

1. Remove the C link by rotating it until it is loose.
2. Slide the stem through the base to access the suction unit.
3. Remove the spring and clip then replace the diaphragm washer.
4. Once the diaphragm washer has been replaced, secure the clip and re-fit the spring.
5. Slide the suction unit back through the base.
6. Re-connect the C link to the stem.

WARNING : If using the syphon with a ball valve, ensure it does not pool around the C link when it fills as this will disable the half-flush mechanism.

For more information please contact:
VIVA Sanitary Units 1-2 Capitol Trading Park, Kirkby Bank Road Knowsley Industrial Estate, Liverpool, L33 7SY

• Tel : 0151 546 0531
• Fax : 0151 549 4187
• E-mail : sales@vivasanitary.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>