Tern Bicycles HSD Gen 1 Duo Stand Owner’s Manual

: June 13, 2024
: tern Bicycles

Table of Contents

Safety
What’s Included
Installation
for Quick Haul & Short Haul Owners
Optional: Install Lockstand™ Extensions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Tern Bicycles HSD Gen 1 Duo Stand

ROSIERES RFC5M594PN Built In Pyrolysis Oven

Safety

If you are unsure how to install this product, please visit your local dealer.
Do not exceed the load limit of 60 kg (132 lb). Please remember the max load limit includes the weight of the bike.
Never leave children or pets on a parked bike unattended.

What’s Included

DuoStand
M10 x 30 Bolt x 2
M10 x 70 Bolt x 1
M10 Nut x 2
M10 Washer x 4
M10 Spring Washer x 1
Flat Plat

What’s Included

Additional Kit Required (For HSD Gen 1 Owners Only)

The Duo Stand HSD Kit (sold separately) is required to install the Duo Stand on the HSD Gen 1. Please see the illustrations on the next page to determine which HSD frame you have.

* DuoStand HSD Kit

M10 x 45 Bolt x 2
Bushing x 2
Wing-shaped Plate

What’s Included

Installation

Tools required (not included)

17 mm Wrench x 2
3, 4 or 5 mm Allen Wrench*

Additional tools required for installation on NBD

Hacksaw
Hand File

Add anti-seize lubricant to the tip of the bolts before securing the nuts. If anti-seize lubricant is not available, apply any standard lubricant to reduce friction and prevent thread galling.

Remove the existing kickstand. (Tool may differ depending on your bike.)

Identify the HSD Frame
Install Bolt Sets in the order and arrangement shown below.
HSD Gen 1 Assembly Order
Nut
Washer
Wing-shaped plate*
Bushing*
Bike frame
Flat plate
DuoStand
Washer
Bolt*

Use parts from
the DuoStand
HSD Kit
HSD Gen 1A Assembly Order

1. Nut
2. Washer
3. Bike frame
4. Flat plate
5. DuoStand
6. Washer
7. M10 x 30 Bolt

HSD Gen 1 Assembly Order

WARNING: Route cables as shown to avoid damage from compression.
HSD Gen 1 only Mounting Location for HSD Gen 1 and Gen 1A

for Quick Haul & Short Haul Owners

install the Bolt Sets in the order and arrangement shown below
Assembly Order
Nut
Washer
Bike frame
DuoStand
Washer
M10 x 30 Bolt
Prepare the DuoStand
a. Remove DuoStand Ends from DuoStand.
b. Measure and use a hacksaw to shorten the legs of the DuoStand by 60 mm. Use a hand file to smooth any metal burrs.
c. Reinstall the DuoStand Ends and loosely tighten the bolts. Bolts will be fully tightened after height is adjusted in Step 3.
install the Bolt Sets in the order and arrangement shown below.
Nut
Spring washer
Washer
Bike frame
DuoStand
Washer
M10 x 70 Bolt
he recommended clearance from the bottom of the rear wheel to the ground is 10 – 20 mm (2/5” – 4/5”). Measure the distance from the bottom of the rear tire to the ground and adjust the height of the DuoStand by loosening the bolts on the DuoStand Ends to raise or lower the legs. Tighten the bolts to a torque of 8 – 9 Nm.

Optional: Install Lockstand™ Extensions

For maximum stability when parked, install the Lockstand Extensions. Available for purchase from your local Tern dealer.

****The Lockstand Extensions are not recommended for installation on the NBD.

LIMITED PRODUCT WARRANTY INFORMATION: This Product comes with a ONE (1) YEAR Limited Warranty from the date of retail purchase by the original end-user. If a material or workmanship defect arises and a valid claim is received within the Warranty Period, this Product will be replaced. Mobility Holdings cannot be held liable for damages to personal property due to misuse or improper care and maintenance. This Product Warranty does not, under any circumstance, cover the replacement or cost of any third party product used with or connected to the Product.

Tern, the Tern Werd (logotype), the Tern Berd (device), Lockstand, and DuoStand used alone or in combination are trade names, trade devices or registered trademarks of Mobility Holdings, Ltd.

© 2022. Tern is a trademark of Mobility Holdings, Ltd. All Rights Reserved.
@ternbicycles
ternbicycles.com

ROSIERES-Logo