SAFAVIEH LIGHTING PND4081 Moshe Pendant Assorted Instruction Manual
- June 13, 2024
- SAFAVIEH LIGHTING
Table of Contents
SAFAVIEH LIGHTING PND4081 Moshe Pendant Assorted
Product Information
The product is a lighting fixture with the model number PND4081. It has the following dimensions: 15.5 inches in length, 15.5 inches in width, and an adjustable height ranging from 15 to 86 inches.
Part List and Hardware List
- Canopy (D)
- Hanging Loop (E)
- Mounting Plate (A)
- Canopy Nut (F)
- Closable Link (H)
- Fixture Loop (I)
- Shade (J)
- Wire nut
- Mounting Screw (C)
- Bulbs (K)
Product Usage Instructions
Preparation:
- Before starting the assembly, ensure that you have all the parts mentioned in the part list and hardware list.
- If any part is missing or damaged, do not proceed with the assembly.
- The estimated assembly time is 20 minutes.
- If you face any difficulties during the assembly, you can contact our Customer Care team at customersupport@safavieh.com for assistance.
Note:
Please use a Type B bulb with a maximum wattage of 60 watts or a CFL bulb
with a maximum wattage of 13 watts or an LED bulb with a maximum wattage of 9
watts. There is an LED 4-watt bulb included in the box.
Step 1:
- Unpack all the parts carefully from the cartons.
- Place the Canopy (D) onto the Hanging Loop (E).
- Insert the tube of the Mounting Plate (A) into the threaded portion of the Hanging Loop (E) and secure it by turning the Canopy Nut (F) clockwise until tight.
- Attach the Closable Link (H) onto the Hanging Loop (E).
Step 2:
- Thread the Fixture Loop (I) to the Shade (J) of the nipple.
- Attach the Closable Link (H) onto the Fixture Loop (I).
Step 3: Wire connection
- Connect the fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire nut.
- Connect the fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire nut.
CAUTION: Do not reverse the hot and neutral connections.
Grounding Instructions:
- Wrap the ground wire from the outlet box around the green ground screw on the Mounting Plate (A), ensuring it is no less than 2 inches from the wire end. Tighten the ground screw.
- If the fixture is supplied with a ground wire, connect it to the outlet ground wire using a wire connector.
Step 4:
- Install the Mounting Plate (A) to the junction box using the Mounting Screw (C).
Step 5:
- Separate the Mounting Plate (A) from the Canopy (D) by turning the Canopy Nut (F) anti-clockwise.
- Attach the Canopy (D) to the junction box and fix it by turning the Canopy Nut (F) clockwise.
Step 6:
- Insert the bulbs (K) into the sockets.
Model# : PND4081
Product Dimensions
- 15.5″L X 15.5″W X 15-86″H
WARNING
- WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN **
- Switch off the main electrical supply from the main fuse box/circuit breaker before installation.
- Inspect the item carefully before attempting to install it.
- If there is any damages or obvious defects, do not install them.
- The item may not be returned once it has been installed.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guidelines below for safe use and installation
- The external flexible cable or cord of this lamp cannot be replaced
If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PREPARATION
- Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list.
- If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 20 minutes.
- If you are having difficulty, our friendly Customer Care team is always here to help. Please email customersupport@safavieh.com
NOTE : PLEASE USE TYPE”B” BULB MAX 60-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WATT, THERE IS AN LED 4-WATT BULB IN THE BOX
-
Step 1: Unpack all parts from the cartons carefully. Place the Canopy(D)onto the Hanging Loop(E).
Place the tube of Mounting Plate(A)into the threaded portion of the Hanging Loop(E) and fix it by turning the Canopy Nut(F) clockwise till tight. Attach the Closable Link(H) onto the Hanging Loop(E). -
Step 2:Thread Fixture Loop (I) to Shade(J) of the nipple. Attach the Closable Link(H) onto the Fixture Loop (I).
-
Step 3: Wire connection
Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire nut. Connect the fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire nut.
CAUTION : Do not reverse the hot and neutral connections
Grounding Instructions:
Wrap ground wire from outlet box around the green ground screw on mounting Plate (A), no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector. -
Step 4: Install the Mounting Plate(A) to the junction box with Mounting Screw (C). Separate the Mounting Plate(A) from the Canopy(D) by turning the Canopy Nut(F) anti-clockwise.
-
Step 5: Attach the Canopy(D) to the junction box and fix it by turning the Canopy Nut(F) clockwise.
-
Step 6: Insert the bulbs (K) into the Sockets
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>