TRIFECTA E Series Tonneau Cover Instruction Manual

June 13, 2024
Trifecta

TRIFECTA E Series Tonneau Cover Instruction Manual
TRIFECTA E Series Tonneau Cover

NO TOOLS REQUIRED

NOTE: It is important that all areas where the bed cover mounts are clean and free of debris prior to installing.
Tools

Place the assembled tonneau over the cab end of the truck box.
Instruction

Unfold the tonneau fully and adjust the position over thetruck bed for proper cab and tail alignment.
Then carefully refold the tonneau without shifting its position on the truck bed.
Instruction

Stop Icon
If your truck has a plastic bed rail cap that extends below the truck sheet metal bed flange, you MUST remove enough of the plastic so that the clamps make solid contact with the truck’s sheet metal.

This is commonly found on 04-14 & 21 Ford F150s and 09-19 RAMs, but your specific vehicle should be inspected carefully to ensure a proper installation.

BEFORE

Plastic bed rail cap.
Installation

AFTER

Plastic bed rail cap.
Installation

Trim the plastic high enough to expose the truck metal, and wide enough to accommodate the clamp.

Do NOT cut into or scrape the truck bed.

Tail clamp
Cab clamp
Cab clamp
Cab clamp
Ensure that the clamp is positioned under the metal bed flange. Hand tighten until clamp contacts the flange, then tighten an additional two turns. Do Not secure to only the lip of the bedliner or wall cap. Do Not Use a Wrench or Overtighten!
Installation

With the tailgate open, completely close the tonneau.
Installation

Slide the rear clamp out to the bed wall. Pull the rear clamp down, and hook it under the bottom edge of the metal bed flange.
Installation

Truck beds with metal flanges (without cargo rails)

Open the cover. The tethers are attached to the cover bow. Attach the clamp to the metal flange of the truck bed rail and tighten the knob. Do this for both the driver and passenger side.
Truck beds with metal flanges

Truck beds with factory cargo rails

Open the cover.

Remove the cargo rail end cap and any tie-down cleats.
Installation

Thread the tether knob through the lock washer, through the tether bracket and into the slide block.
Installation

Insert the provided slide block into the cargo rail.
Installation

Tighten the knob. Do these steps for both the driver and passenger sides.
Installation

Move the slide block forward to the front bow of the cover.
Installation

Reinstall any tie-down cleats and the end cap on both sides of the truck.
Installation

DRIVING WITH THE TONNEAU OPEN

Release the rear clamps and fold the tonneau forward.
Installation

IMPORTANT: Before folding the second section of the to nneau, the rear clamps must be stowed into the rail to prevent damage to the fabric. Failure to stow the handle will puncture the tarp and void the warranty.
Installation

Fold the tonneau forward and fasten the straps in the middle section to the front rail. Check that the straps are tight.
Installation

IMPORTANT

Re-tighten the front/cab clamps and tethers after the first week of driving the vehicle.
Also periodically check the clamps and tethers to ensure they are secure.

Closed/Extended Position – Bed cover must be completely secured by all four (4) clamps.
Open/Folded Position – Bed cover must be completely folded up (all panels) and secured at the cab with the provided buckles straps and with both tethers attached.
Do   NOT drive with the bed cover in a partially open position.
Installation

NOTE: the tarp cannot be removed from the aluminum frame. Attempting to do so will cause damage and void the warranty.

Do NOT allow the vehicle to be towed backwards without first removing the cover from the vehicle.
Safety Instruction

Remove any snow or foreign matter before folding the bed cover.

CARGO MANAGEMENT EQUIPPED TRUCKS

BRACKET KIT INSTALLATION

Installation

Add the clamp plate, washers and screws as shown.
Installation

REPLACEMENT PARTS

NOTE: To order replacement parts, it is best to contact our Customer Service Department for assistance to ensure that you get the correct part for your vehicle application. When ordering, xxx represents the 3 digit suffix, as referenced on the sales receipt or vehicle application list.
Parts

Call Out| Title| Part Number| Description| Model Year| Qty
---|---|---|---|---|---
A| Cab Seal| 32440500| 1/2” D Seal (6’) fits most applications| | 1
A| Cab Seal| 32562569| 3/4” Two-fin Seal (69.5”) fits Nissan Frontier applications| 2005-2020| 1
A| Cab Seal| 32562569| 3/4” Two-fin Seal (69.5”) fits Chevy Silverado/GMC applications| 2019-2020| 1
A| Cab Seal| 32001668| 1 3/8” Foam Seal (5’5”) fits Toyota Tacoma applications| 2005-2015| 1
A| Cab Seal| 32270600| Honda Ridgeline| 2006-2020| 1
B| Tail Seal| 32520000| Standard Tail Fin Seal (68”) fits all trucks except Toyota Tacoma| | 1
B| Tail Seal| 32001668| 1 3/8” Foam Seal (5’5”) fits Toyota Tacoma applications| 2005-2015| 1
C| Side Seal| 32520052-0| Bulb Seal (8’)| | 1
D| Corner| 24520100| Corner only, used front or rear| | 1
E| Corner Pad| 32520001| Pad only, used front or rear, 3/8” thick| | 1
| Corner Pad| 32520002| Pad only, used front or rear, 1/2” thick| | 1
| Corner Pad| 32520003| Pad only, used front or rear, 3/4” thick| | 1
F| Tailgate Hinge Assembly| 35521033| | | 1
G| Cab Hinge Assembly| 35521032| | | 1
H| Cab Clamp Assembly| 1034| | | 1
I| Tailgate Clamp Assembly| 1035/1042| | | 1
J| Short Tarp Tie Down Strap| 54440400| Short Tie Down Strap w/Male Buckle, used with 4-bow configuration| | 1
K| Long Tarp Tie Down Strap| 54720400| Long Tie Down Strap w/Male Buckle, used with 3-bow configuration| | 1
L| Buckle Assembly| 54440100| Single Buckle assembly w/Female Buckle for Tie-down Strap| | 1

LIMITED WARRANTY

WARRANTY COVERAGE
This truck bed cover is warrantied against defects in materials or workmanship as follows. This warranty is void if the product has been damaged in an accident, or due to neglect, unforeseeable use, improper installation, improper servicing, or other cause not arising out of defects in material or workmanship.

LIMITED FIVE-YEAR WARRANTY ON HARD PARTS
All hardware included with your truck bed cover, including rails, clamps and bows carry a limited warranty for five (5) years from the original date of purchase, subject to the terms below.
LIMITED FIVE-YEAR WARRANTY FOR FABRIC
The fabric on your truck bed cover carries a limited warranty for five (5) years from the original date of purchase, subject to the terms below.

WARRANTY IS NOT TRANSFERABLE
The warranty is to the initial consumer purchasing the truck bed cover and it is not transferrable to a subsequent end user. Proof of purchase may be required to enforce these warranty rights.

FAILURE TO FOLLOW THESE CARE AND USE INSTRUCTIONS WILL VOID THE WARRANTY

  • Clean with mild automotive soap and water only.
  • Use only water-based vinyl conditioners. Use of vinyl conditioners that contain silicone or petroleum (e.g., Armor All®) may crack and shrink the vinyl and will void the warranty.
  • Prior to vehicle operation, all clamps and retention mechanisms must be tightly secured to the vehicle:
    • Closed/Extended Position – Bed cover must be completely secured by all four (4) clamps.
    • Open/Folded Position – Bed cover must be completely folded up (all panels) and secured at the cab with the provided buckles straps and with both tethers attached. Do NOT drive with the bed cover in a partially open position!
  • The truck bed cover MUST be free of foreign material, including snow and ice, before opening.
  • Rear/tailgate panel clamps must be properly stored prior to folding the cover in order to prevent damage to the fabric.
  • Front/cab clamps and retention mechanisms must be checked for tightness after a week of driving following installation (or re-installation) of the truck bed cover and periodically thereafter.
  • Do NOT allow the vehicle to be towed backwards without first removing the cover from the vehicle

WARRANTY PERFORMANCE
If all warranty conditions are met, a defective truck bed cover, tarp, or hardware component will either be repaired or replaced (at our option). We reserve the right, for any warrantied return, to substitute a newer model of bed cover having similar form and function, to offer a warranty discount on an entire replacement system, and/or provide remedies other than those mentioned in this document.

WARRANTY PROCESS
A Return Authorization number must be obtained from our Customer Service Department prior to returning any product. We may require the original item to be returned postage prepaid for final determination. Shipping charges will apply for any repair or replacement. Other than postage or shipping charges, no charge will be made for repair or replacement under this warranty.

This warranty gives you specific legal rights. As a consumer, you may also have additional rights and remedies under the laws of your state.

WARRANTY REGISTRATION
Warranty registration must be on file and/or proof of original purchase (detailed and dated receipt) required for warranty to be effective.

Register online at https://extang.com/warranty-registration

REGISTER YOUR WARRANTY ONLINE

Experienced Customer Service staff are available to answer all your truck bed cover questions

CUSTOMER SERVICE

8:30 TO 6:00 EST, MONDAY – FRIDAY

Tonno Model: ____
Purchase Date: ____
Lot Code: ____
Lot code can be found on underside of cover.

Extang Corporation  5400 S. State Road, Ann Arbor, MI 48108 • 800-877-2588 © Extang Corporation, 2022
Part# 31770100-30 Rev. 7-8-22

TRIFECTA Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals