AsReader ASR-A24D Barcode Parameters for HID Mode Instructions
- June 13, 2024
- AsReader
Table of Contents
- Preface
- How To Change The Settings
- Default Settings of ASR-A24D
- Factory Default
- Vibration： “@VIBONX”
- Sleep Mode: ”@SLMONX”
- Beep After Scan: “@BASONX”
- Battery Gauge LED: “@BGLONX”
- Power On Beep: “@POBONX”
- Inter-Character Delay: “@ICDSVX”
- Country Keyboard Layout Type Code: “@CKLTCX”
- Continuous Read: “@CTRONX”
- Appendix
- Customer Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AsReader ASR-A24D Barcode Parameters for HID Mode
Preface
Copyright © Asterisk Inc. All Rights Reserved.
AsReader ® is registered trademarks of Asterisk Inc.
The contents of this manual are subject to change without notice.
This manual describes the parameters required for some settings when using AsReader ASR-A24D (hereinafter referred to as ASR-A24D) in HID mode. For other settings, please refer to the dedicated barcode setting manual.
How To Change The Settings
Select the appropriate setting code from this manual and scan it. The new
settings will be saved in the ASR-A24D.
Note : Make sure the ASR-A24D’s battery is fully charged before setting.
If you have any comments or questions about this manual, please contact us:
Online, via https://asreader.com/contact/
Or by mail, at: Asterisk Inc., AsTech Osaka Building 6F, 2-2-1, Kikawa nishi,
Yodogawa-ku, Osaka, 532-0013, JAPAN
TEL: +81 (0) 50 5536 8733 in Japanese
TEL: +1 503-770-2777 x102 in Japanese
or English (U.S.A.)
TEL: +31 (0) 10 808 0488 in Japanese or English (E.U.)
Default Settings of ASR-A24D
ASR-A24D is shipped with the settings stated in the table below.
In this manual, the default parameter of each item is marked with an asterisk
(*).
| Item | Default | Page |
|---|---|---|
| Factory Default | – | P.3 |
| Vibration | Vibration On | P.4 |
| Sleep Mode | Sleep Mode On | P.5 |
| Beep After Scan | Beep After Scan On | P.6 |
| Battery Gauge LED | Battery Gauge LED On | P.7 |
| Power On Beep | Power On Beep On | P.8 |
| Inter-Character Delay | 10ms delay | P.9~P.10 |
Country Keyboard Layout
Type Code
| North American Standard
Keyboard
| P.10
Continuous Read| Continuous Read Off| P.11
Appendix| –| P.12
Factory Default
Scan the ‘Reader FACTORY DEFAULT’’ barcode above to return barcode parameter
values to factory default values.
Scanning is not possible while Factory Default is running. Factory Default
execution takes 2 seconds.
Factory Default
@FCTDFT
Vibration： “@VIBONX”
Scan the appropriate code below to set whether to vibrate when scanning a barcode.
| Vibration Off | Vibration On＊ |
|---|
| 
@VIBON0| @VIBON1
Current Value?|
---|---
|
@VIBON?|
Sleep Mode: ”@SLMONX”
Scan the appropriate code below to set whether to apply sleep mode to ASR- A24D.
| Sleep Mode Off | Sleep Mode On＊ |
|---|
| 
@SLMON0| @SLMON1
Current Value?|
---|---
|
@SLMON?|
Beep After Scan: “@BASONX”
Scan the appropriate code below to set whether to beep when scanning a barcode.
| Beep After Scan Off | Beep After Scan On＊ |
|---|
| 
@BASON0| @BASON1
Current Value?|
---|---
|
@BASON?|
Battery Gauge LED: “@BGLONX”
Scan the appropriate code below to enable or disable the battery gauge LED (Battery level indicator) on the back of ASR-A24D.
| Battery Gauge LED Off | Battery Gauge LED On＊ |
|---|
| 
@BGLON0| @BGLON1
Current Value?|
---|---
|
@BGLON?|
Power On Beep: “@POBONX”
Scan the appropriate code below to set whether to beep when ASRA24D is powered on.
| Power On Beep Off | Power On Beep On＊ |
|---|
| 
@POBON0| @POBON1
Current Value?|
---|---
|
@POBON?|
Inter-Character Delay: “@ICDSVX”
Scan the appropriate code below to set the display interval time between characters of the barcode data.
| 5ms delay | 10ms delay＊ |
|---|
| 
@ICDSV1| @ICDSV2
15ms delay| 20ms delay
---|---
| 
@ICDSV3| @ICDSV4
25ms delay| 35ms delay
---|---
| 
@ICDSV5| @ICDSV7
50ms delay| Current Value?
---|---
| 
@ICDSVA| @ICDSVA?
Country Keyboard Layout Type Code: “@CKLTCX”
Scan the appropriate code below to set country keyboard layout of ASR-A24D.
| North American Standard Keyboard＊ | German Keyboard(QWERZ) |
|---|
| 
@CKLTC0| @CKLTC1
Current Value?|
---|---
|
@CKLTC?|
Continuous Read: “@CTRONX”
Scan the appropriate code below to set Continuous Read of ASRA24D.
| Continuous Read Off＊ | Continuous Read On |
|---|
| 
@CTRON0| @CTRON1
Current Value?|
---|---
|
@CTRO?|
Appendix
Barcode module factory default
Restore Defaults
Set Factory Defaults
Decode Data Packet Format
Send Packeted Decode Data
Customer Support
AsReader
ASR-A24D Barcode Parameters for HID Mode
Jan. 2023 1nd version
Asterisk Inc.
AsTech Osaka Building 6F, 2-2-1, Kikawa nishi, Yodogawa-ku,
Osaka, 532-0013, JAPAN
