JYTEK PXI-93518 8 Ports Serial Communication Modules User Manual

June 13, 2024
JYTEK

JYTEK PXI-93518 8 Ports Serial Communication Modules

JYTEK-PXI-93518-8-Ports-Serial-Communication-Modules-
product

Product Information

  • Product Name: PXI-93518 8 Ports Serial Communication Modules
  • Manufacturer: JYTEK
  • Manufacturer’s Website: http://www.jytek.com

Product Usage Instructions

Introduction

The PXI-93518 is a serial communication module with eight RS-422/485/232 ports. It allows you to set the baud rate, data bit length, stop bit length (1 or 2 stop bits), and parity mode.

PXI-93518 Connector Pin Assignment

Pin RS-232 RS-422 RS-485 Port #
3 OUT1+ A1
2 OUT1- B1
50 IN1+
49 IN1-
26 Port1

Introduction

PXI-93518 Overview

What is the PXI-93518

PXI-93518 is an eight ports serial communication module, compatible with RS-422, RS-485 and RS-232 standards, with fast transient voltage suppression protection circuit. This protector can effectively suppress lightning and ESD, provide 600W lightning surge protection power for each line, as well as surge voltage and transient overvoltage generated on the line for various reasons, and the very small inter pole capacitance ensures the high-speed transmission of RS-422 / RS-485 / RS-232 interface.

PXI-93518 Features

JYTEK-PXI-93518-8-Ports-Serial-Communication-Modules-
fig-1 JYTEK-PXI-93518-8-Ports-
Serial-Communication-Modules-fig-2

  • Eight RS-422 / 485 / 232 communication ports
  • Baudrate, data bit length, stop bit length (1 or 2 stop bits) and parity mode can be set
  • Baud rate:
    1. RS-422 and RS-485 support up to 921.6k bps;
    2. RS-232 supports up to 115,200 bps.
  • Receiving circuit with pull-down resistor
  • Standard serial port operation mode
  • All ports adopt photoelectric isolation and ± 15kV surge protection
  • 120Ω terminal resistance matching
  • Operation System Compatibility: Windows 7/ 10
  • Operating temperature: -40℃~+85℃
  • Relative Humidity: 0~90%

PXI-93518 Connector Pin Assignment

DB62 female connector pin assignment for the PXI-93518.

Table 1:  PXI-93518 Connector Pin Assignment

Pin RS-232 RS-422 RS-485 Port #
3   OUT1+ A1

Port1

2|  | OUT1-| B1
50|  | IN1+|
49|  | IN1-|
26| TX1|  |
25| RX1|  |
54| GND
5|  | OUT2+| A2|

Port2

4|  | OUT2-| B2
48|  | IN2+|
47|  | IN2-|
24| TX2|  |
23| RX2|  |
53| GND
8|  | OUT3+| A3|

Port3

7|  | OUT3-| B3
46|  | IN3+|
45|  | IN3-|
30| TX3|  |
29| RX3|  |  |
---|---|---|---|---
52| GND
10|  | OUT4+| A4|

Port4

9|  | OUT4-| B4
44|  | IN4+|
43|  | IN4-|
28| TX4|  |
27| RX4|  |
51| GND
14|  | OUT5+| A5|

Port5

13|  | OUT5-| B5
62|  | IN5+|
61|  | IN5-|
38| TX5|  |
37| RX5|  |
12| GND
16|  | OUT6+| A6|

Port6

15|  | OUT6-| B6
60|  | IN6+|
59|  | IN6-|
36| TX6|  |
35| RX6|  |
11| GND
19|  | OUT7+| A7|

Port7

18|  | OUT7-| B7
58|  | IN7+|
57|  | IN7-|
42| TX7|  |
41| RX7|  |
6| GND
21|  | OUT8+| A8|

Por8

20|  | OUT8-| B8
56|  | IN8+|
55|  | IN8-|
40| TX8|  |
39| RX8|  |
1| GND

Table 2: Notes to Legend in the Pin Definitions

Installation

This chapter describes the configurations of the serial communication module. The contents in the package and unpacking information that the user should be aware of are described in the beginning.

What You Have

In addition to this User’s Manual, the package includes the following items:

  • PXI-93518 Serial Communication Interface Module
  • DB62 Connector

Unpacking

  • Your serial communication module contains sensitive electronic components that can be easily damaged by static electricity.
  • The module should be done on a grounded anti-static mat. The operator should be wearing an anti-static wristband, grounded at the same point as the anti-static mat.
  • Inspect the module carton for obvious damage. Shipping and handling may cause damage to your module. Ensure there are no shipping and handling damages on the module before processing.
  • After opening the module carton, remove the system module and place it only on a grounded anti-static surface component side up.
  • Again inspect the module for damage. Press down on all socket IC’s to ensure they are properly seated. Do this only with the module placed on a firm flat surface.

Note: DO NOT APPLY POWER TO THE MODULE IF IT HAS BEEN DAMAGED.
You are now ready to install your PXI Module.

Installation Procedure

  1. Turn off your PXI computer system.
  2. Turn off all accessories (printer, modem, monitor, etc.) connected to computer.
  3. Select a PXI slot.
  4. Before handling the serial communication module, discharge any static buildup on your body by touching the metal case of the computer. Hold the edge and do not touch the components.
  5. Position the module into the PXI slot selected.
  6. Secure the module in place of the system.

Hardware Configuration

The serial communication module has Plug and Play component, the card can requests memory usage (I/O port locations) of the card which is assigned by system BIOS. The address assignment is done on a board-by-board basis for all serial communication cards in the system.

Software Installation

Windows 7 Installation

JYTEK-PXI-93518-8-Ports-Serial-Communication-Modules-
fig-4

  1. After slacing the PXI-93518 in the chassis, open the [Device manager] ,and you will see a unknown device with question mark.
  2. Right click the device, select the [update driver software] button.
  3. Select the [Browse your computer for driver software].JYTEK-PXI-93518-8-Ports-Serial-Communication-Modules-fig-7
  4. When prompted for the path, specify the drive and directory where the new driver for the card installed. Choose x64 or x86 depending on the computer system.
  5. Follow the configuration dialog boxes to install the driver.
  6. Now you can see the port device and eight unknown multifunction device. Use the above method to update the driver for eight devices respectively
  7. Now the port device are all identified. Serial port number starts from the smallest available number in the system.

Note: Unload the driver before removing the board to avoid occupying the system port resources.

Warranty Policy

Thank you for choosing JYTEK. To understand your rights and enjoy all the after-sales services we offer, please read the following carefully.

  1. Before using JYTEK‘s products please read the user manual.and follow the instructions exactly.
  2. Our repair service is not covered by JYTEK‘s guarantee in the following situations:
    • Damage caused by not following instructions in the User’s Manual.
    • Damage caused by carelessness on the user’s part during product transportation.
    • Damage caused by fire, earthquakes, floods, lightening, pollution, other acts of God, and/or incorrect usage of voltage transformers.
    • Damage caused by inappropriate storage environments such as with high temperatures, high humidity, or volatilechemicals.
    • Damage caused by leakage of battery fluid during or after change of batteries by customer/user.
    • Damage from improper repair by unauthorized JYTEK technicians.
    • Products with altered and/or damaged serial numbers are not entitled to our service.
    • This warranty is not transferable or extendible.
    • Other categories not protected under our warranty.
  3. Customers are responsible for all fees necessary to transport damaged products to JYTEK.

For further questions, please e-mail staff: info@jytek.com

© Copyright 2021 Shanghai Jianyi Technology Co., Ltd
All Rights Reserved.

Manual Revision 1.0: Nov 10, 2021

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

PXI-93518 are registered trademarks of JYTEK, Windows 7, Windows 10 are registered trademarks of Microsoft- Corporation. Intel@ is a registered trademark of Intel Corporation.Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Getting Service

Customer satisfaction is our top priority. Contact us should you require any service or assistance.

SHANGHAI JYTEK CO., LTD.

  • Web Site: http://www.jytek.com
  • Sales & Service: service@jytek.com
  • Telephone No.: +86-21-50475899
  • Fax No.: +86-21-50475899
  • Mailing Address: 300 Fangchun Rd., Zhangjiang Hi-Tech Park, Pudong New Area, Shanghai 201023 China
  • jytek.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals