LUTEC 5288801012 Wall Lantern User Manual

: June 13, 2024
: LUTEC

Table of Contents

LUTEC 5288801012 Wall Lantern
Product Information
Product Usage Instructions
PACKAGE CONTENTS
SAFETY INFORMATION
INSTALLATION
CARE AND MAINTENANCE
TROUBLESHOOTING
3-YEAR LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LUTEC 5288801012 Wall Lantern

Product Information

Model: 5288801012/5288801412
Product Name: Wall Lantern
Description: This wall lantern is designed to provide outdoor lighting. It includes a fixture and a glass cover.

Product Usage Instructions

Preparation:

Before starting the assembly or installation, ensure that all parts are present.
Compare the parts with the package contents list and hardware contents list.
If any part is missing or damaged, do not proceed with the assembly, installation, or operation of the product.
Estimated Assembly Time: 20-30 minutes.
Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking Adhesive, Ladder.

Installation:

Turn OFF power to the work area at the main circuit breaker or fuse box.
CAUTION: Do not rely on the wall switch alone to turn off power.
Install the bulb (not included) into the fixture (A).
Rotate the glass cover (B) into the fixture (A).
Remove the mounting bracket from the fixture (A) by unscrewing the pre-assembled screws. Keep these two screws aside as they will be used later.
Rotate the mounting bracket so that the top is level. Attach the mounting bracket to the junction box (not included) using the two screws (AA).
Connect the ground wire from the junction box to the ground screw on the mounting bracket. Then connect the ground wire from the junction box to the ground wire from the fixture (A) by twisting a wire nut (BB) onto the bare ends of the wires.
Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires.
Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires.
Position all the wires inside the fixture junction box.
Attach the light fixture (A) to the mounting bracket using the screws previously removed in step 4.
After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.
Turn ON power to the work area at the main circuit breaker or fuse box.

Care and Maintenance

Troubleshooting:

Problem	Possible Cause	Corrective Action
The light will not go on.

No power.
Fixture may be wired incorrectly.
Switch may be wired incorrectly. Crossed wires or power wire is
grounding out.

|

Make sure lamp fixture is plugged in and power is on.
Check wiring.
Check wiring. Consult a certified electrician.

Fuse blows or circuit trips when fixture is turned on.|

No power.
Fixture may be wired incorrectly.
Switch may be wired incorrectly. Crossed wires or power wire is
grounding out.

|

Make sure lamp fixture is plugged in and power is on.
Check wiring.
Check wiring. Consult a certified electrician.

Warranty:

This product comes with a 3-year limited warranty. If the product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, it will be replaced with the same or a comparable model free of charge.
This warranty is void if the damage or defect has resulted from accident, abuse, misuse, or faulty repair. This warranty provides specific legal rights, and you may have other rights that vary from state to state.

WALL LANTERN
MODEL #5288801012/5288801412

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

PACKAGE CONTENTS

$LUTEC-5288801012-Wall-Lantern-01 $1$$

PART	DESCRIPTION	QUANTITY
A	Fixture	1
B	Glass Cover	1

HARDWARE CONTENTS (not shown actual size)

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

Consult a qualified electrician if you are not certain about the installation process. Always install wiring connections in accordance with local code, ordinances and the National Electric Code.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This light fixture is designed to fit standard junction boxes as defined by the National Electrical Code.
This light fixture is not dimmable.

PREPARATION

Before beginning to assemble or installing lighting fixture, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Estimated Assembly Time: 20-30 minutes.
Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking Adhesive, Ladder.

INSTALLATION

Turn OFF power to work area at main circuit breaker or fuse box.
CAUTION: Do not rely on wall switch alone to turn off power.
Install the bulb (not included) into the fixture (A).
Rotate the glass cover (B) into the fixture (A).
Remove the mounting bracket from the fixture (A) by unscrewing the pre-assembled screws. Put these two screws a side as they will be used later.
Rotate the mounting bracket so the top is level. Attach the mounting bracket to the junction box (not included) using the two screws (AA).
Connect the ground wire from the junction box to the ground screw on the mounting bracket. Then connect the ground wire from the junction box to the ground wire from the fixture (A) by twisting a wire nut (BB) onto the bare ends of the wires. Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box.
Attach the light fixture (A) to the mounting bracket using the screws previously removed in step 4.
After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.
Turn ON power to work area at main circuit breaker or fuse box.

CARE AND MAINTENANCE

Clean surfaces with a mild, non-abrasive cleaner.

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSE	CORRECTIVE ACTION
The light will not go on.

No power.
Fixture may be wired incorrectly.
Switch may be wired incorrectly.

|

Make sure lamp fixture is plugged in and power is on.
Check wiring.
Check wiring.

Fuse blows or circuit trips when fixture is turned on.| Crossed wires or power wire is grounding out.| Consult a certified electrician.

3-YEAR LIMITED WARRANTY

If this product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge.
This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC: