LIBERTY DL-HD70-H3 HDMI 2.0 Uncompressed 70m Extension Set User Manual

LIBERTY DL-HD70-H3 HDMI 2.0 Uncompressed 70m Extension Set

Product Information

Master
Audio, DTS:X
HDR Support| Yes, including Dolby Vision and HDR10+
HDMI Version| HDMI 2.0
HDCP Compatibility| HDCP 2.2/2.3 compliant
CEC Support| Yes, CEC pass-through

Product Usage Instructions

To use the Digitalinx Series HDBaseT 3.0 70m Extension Set (DL-HD70-H3), follow the instructions below:

Transmitter Setup:

1. Connect the power adapter to the “Power In” port on the transmitter. Either the transmitter or receiver needs to be plugged into power.
2. Connect an HDMI source to the “HDMI in” port on the transmitter.
3. Connect an IR receiver to the “IR in” port on the transmitter.
4. Connect an IR emitter to the “IR out” port on the transmitter.
5. Connect an RS232 device to the “RS-232” port on the transmitter for pass-through to the receiver RS-232 port.
6. Connect a CAT cable to the “HDBT out” port on the transmitter to connect to the receiver.

Receiver Setup:

1. Connect the power adapter to the “Power In” port on the receiver. Either the transmitter or receiver needs to be plugged into power.
2. Connect an HDMI display or projector to the “HDMI out” port on the receiver.
3. Connect an IR receiver to the “IR in” port on the receiver.
4. Connect an IR emitter to the “IR out” port on the receiver.
5. Connect an RS232 device to the “RS-232” port on the receiver for pass-through to the transmitter RS-232 port.
6. Connect a CAT cable to the “HDBT in” port on the receiver to connect to the transmitter.

Configuration Settings:

Use the DIP switch on the receiver to configure the EDID mode:

Application Diagram:

Refer to the application diagram for a visual representation of how to connect the DL-HD70-H3 extension set.

PRODUCT OVERVIEW

• The Digital DL-HD70-H3 HDBaseT 3.0 extender set transmits video, audio, IR, and RS232 over a single category 6a F/UTP or better-twisted pair cable. The DL-HD70-H3 can transmit 4K resolutions up to 4K@60Hz,
  4:4:4 up to 40m / 131’ and 4K30 or below up to 70m / 230’. The Digital DL- HD70-H3 supports HDMI 2.0 and is HDCP 2.2/2.3 compliant and supports CEC pass- through. The Digital DL-HD70-H3 supports multiple audio formats including PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio, and DTS: X. The Digital DL-HD70-H3 supports any HDR format, including Dolby Vision and HDR10+.

• The DL-HD70-H3 has an EDID Dipswitch to allow manual or auto EDID selection.

• The DL-HD70-H3 is sold only as a set with a single power supply and can be powered on either end.

PACKAGE CONTENTS

• DL-HD70-H3 extender set
• (2) 3pin-3.81mm Phoenix Connectors (Male)
• (4) Mounting Ears with Mounting Screws
• 12V 2A Power Adapter with US, UK, AU, AND EU Power Adapters
• (1) IR Emitter
• (1) IR Receiver (30kHz – 50kHz)
• (1) IR-AC Coupler Cable

TRANSMITTER PRODUCT BREAKDOWN

1. Power LED (Red) : When the red power LED is on the transmitter has power.
2. Status LED (Green) : When blinking the units are working properly.
3. Link LED (Green) : Link LED is on, and the transmitter and receiver have a good connection. When it’s off the units are not connected.
4. HDCP LED: Solid light means HDMI signal with HDCP. Flashing light means HDMI signal without HDCP. OFF – No Light means no HDMI signal
5. EDID DIP switch: See the EDID section for settings.
6. Power In : Connects to power adapter. Either the transmitter or receiver needs to be plugged into power.
7. IR in: Connects to the provided IR receiver.
8. IR out: Connects to the provided IR emitter.
9. HDBT out: Connects CAT cable to connect to the receiver.
10. HDMI in: Connects to an HDMI source.
11. RS-232: Connects to an RS232 device Pass-through to receiver RS-232 port.3

RECEIVER PRODUCT BREAKDOWN

1. Power LED (Red): When the red power LED is on the transmitter has power.
2. Status LED (Green): When blinking the units are working properly.
3. Link LED (Green): The link LED is on, and the transmitter and receiver have a good connection. When it’s off the units are not connected.
4. HDCP LED: Solid light means HDMI signal with HDCP. Flashing light means HDMI signal without HDCP. OFF – No Light means noHDMI signal
5. EDID DIP switch: See the EDID section for settings.
6. Power In: Connect to the power adapter. Either the transmitter or receiver needs to be plugged into power.
7. IR in : Connects to the provided IR receiver.
8. IR out: Connects to the provided IR emitter.
9. HDBT in: Connects CAT cable to connect to the transmitter.
10. HDMI out: Connects to an HDMI display or projector.
11. RS-232: Connects to an RS232 device, Pass-through to the transmitter RS-232 port.

CONFIGURATION SETTINGS

APPLICATION DIAGRAM

Below is an example of an extender set in a typical application.

Cabling Requirements

HDBaseT Cabling

• HDBaseT3.0 Specification is made using high-quality Cat6a F/UTP cabling. For maximum full capability performance, ensure Cat6a F/UTP or above is used.
• To ensure proper performance of the DL-HD70-H3, it is recommended that you use solid core, shielded Category 6a F/UTP or above cabling.
• Category 6 or 5e F/UTP may work but may not support power over HDBaseT reliably and may only work over short distances.

When using shielded category cabling ALWAYS…

• use shielded connectors
• to properly ground the category cable
• For optimized HDBaseT performance use the following Liberty Wire and Cable branded cabling;
• Category 6 plenum; 24-4P-P-L6SH
• Category 6A plenum; 24-4P-P-L6ASH
• Category 6 NON-plenum; 24-4P-L6SH
• Category 6A NON -plenum; 24-4P-L6ASH

Twisted Pair Wiring

• Use TIA/EIA-568B wiring for Category 6a connection between send and receive units.

RS232 Wiring

• Connect the controller or device RX signal to TX on the DL-HD70-H3 extender. Connect the controller or device TX signal to Rx on the DL-HD70-H3 extender.

TECHNICAL SPECIFICATIONS

Model| DL-HD70-H3|  |
---|---|---|---
Physical Parameter|
Case Material| Receiver: Industrial-grade metal chassis with metal brackets

Transmitter: Industrial-grade metal chassis with metal brackets

|
Dimensions| Transmitter: 170mm [W] x 105mm [D] x 25mm [H]

Receiver: 170mm [W] x 105mm [D] x 25mm [H]

|
Weight| Transmitter: 265g

Receiver: 265g

|
Power Protection| ESD protection with human body model — ±8kV (Air-gap discharge) & ±4kV

(Contact discharge)

|
Power Output| DC 12V 2A|
Power Input| AC 100-240V 50/69Hz|
Power Consumption| 14.28W (Max)|
Operating Temperature| 32- 113°F / 0- 45°C|
HDMI Specifications|
HDMI| 2.0b|
HDCP| 2.3/2.2/1.4|
Video Bandwidth| 18 Gbps|
Video Resolutions| 4096×2160@24/25/30/50/60Hz,3840×2160@24/25/

30/50/60Hz, 1920x1080p,1080p@23.98/24/25/29.97/

30/50/59.94/60Hz,1080i@50/59.94/60Hz, 720p@50/

59.94/60Hz, 576p, 576i, 480p, 480i

|
Color Space| RGB, YCbCr 4:4:4 / 4:2:2. YUV 4:4:4|
Color Depth| 8/10/12-bit|
Analog Audio Format| LPCM 2.0|
HDMI

Audio Formats

| HDMI IN/OUT: Fully supports audio formats in HDMI 2.0 specification, including

PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio and DTS:X

|
Connectivity|
Inputs| Inputs: 1x HDMI 1x IR IN

1x DC 12V

Rx : 1xHDBT IN [RJ45, Female]

1x IR IN

1x DC 12V

|  |
Outputs| Outputs: 1x HDBT OUT [RJ45, 8-pin female]

1x RS-232 Phoenix jack 3 pin (3.81mm) 1x IR OUT

Rx: 1xHDMI Type A-Female 1x IR OUT

|  |
Transmission|
Max Distance (4K30)| 230ft / 70m over CAT6a 60m over Cat6|
Max Distance (4K60 4:4:4| ) 131ft / 40m over CAT6a/7|

Thank you for your purchase.

• For technical support please call our toll-free number at 800-530-8998 or email us at supportlibav@libav.com
• www.libav.com 800-530-8998

References

• libav.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>