MAYTAG MDTS4224P Hybrid Tub Dishwasher with Heated Dry Instruction Manual
- June 13, 2024
- Maytag
Table of Contents
PRODUCT MODEL NUMBERS
MDTS4224P
MDPS4224R
Undercounted Dishwasher
DRAIN REQUIREMENTS
■ A new drain hose is supplied with your dishwasher. If drain hose is not long
enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets
all current AHAM/IAPMO test standards, is resistant to heat and detergent, and
fits the 1″ (25 mm) drain connector of the dishwasher. See the “Tools and
Parts” section at the front of the guide for part details and orders.
■ Make sure to connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 20″ (508 mm) minimum above the floor. It is
recommended that the drain hose either be looped up and securely fastened to
the underside of the counter or be connected to an air gap.
■ Make sure to use an air gap if the drain hose is connected to house plumbing
lower than 20″ (508 mm) above subfloor or floor.
■ If required, the air gap should be installed in accordance with the air gap
installation instructions. When you are connecting the air gap, a rubber hose
(not provided) will be needed to connect to the waste tee or disposer inlet.
■ Use 1/2″ (13 mm) minimum I.D. drain line fittings.
WATER SUPPLY REQUIREMENTS
■ This dishwasher has a water heating feature and also requires a connection
to a hot water supply line.
■ A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa) water pressure
can be verified by a licensed plumber.
■ 120°F (49°C) water at dishwasher.
■ 3/8″ (9.5 mm) O.D. copper tubing with compression fitting or flexible
braided water supply line. See the “Tools and Parts” section at the front of
the guide for part details and orders.
NOTE: 1/2″ (13 mm) minimum plastic tubing is not recommended.
■ A 90° elbow with 3/4″ (19 mm) hose connection with rubber washer. See the
“Tools and Parts” section at the front of the guide for part details and
orders.
■ Do not solder within 6″ (152 mm) of the water inlet valve.
■ If installed in new construction, make sure the house water supply lines
have been flushed prior to connecting the dishwasher to remove any debris that
may exist in the supply line.
NOTE: If replacing an existing dishwasher, it is recommended to install a
new water line (see the “Tools and Parts” section at the front of the guide
for part details) and drain hose (supplied) with the new dishwasher.
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical
shock.
You Must Have:
■ 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply.
■ Copper wire only.
■ A maximum of 2 field wiring supply conductors (12 AWG largest size) plus 1
grounding conductor are permitted in the terminal box.
We Recommend:
■ A time-delay fuse or circuit breaker.
■ A separate circuit.
If Connecting Dishwasher with a Power Cord:
■ Use UL Listed power cord kit marked for use with dishwasher. See the “Tools
and Parts” section at the front of the guide for part details and orders.
■ Plug into a grounded 3 prong outlet. Outlet must meet all local codes and
ordinances.
If Connecting Dishwasher with Direct Wiring:
■ Use flexible, armored, or nonmetallic sheathed copper wire with grounding
wire that meets the wiring requirements for your home and local codes and
ordinances.
■ Use a UL Listed/CSA Approved metallic strain relief.
PRODUCT DIMENSIONS (FOR MDTS4224P AND MDPS4224R)
For 4″ (100 mm) toe kick, height of cabinet opening is 341/2″ (863 mm).
A. Insulation may be compressed (not used on all models).
B. Door handles may protrude forward of the face of the dishwasher, (varies by
model).
CABINET OPENING DIMENSIONS
A. Measured from the lowest point on the underside of the countertop. May be
reduced to 33 1/2″ (851 mm) by removing the wheels and perforated area of
insulation (blanket) on dishwasher.
B. Minimum, measured from narrowest point of opening.
Because Maytag® Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications
without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
W11666379A
®/™ ©2023 Maytag. All rights reserved. Used under license in Canada.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>