Whirlpool FFWDB Washing Machine User Guide
- June 13, 2024
- Whirlpool
Table of Contents
Whirlpool FFWDB Washing Machine
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT. For even more complete user support, register your appliance at www.whirlpool.eu/register
- Please read the content of the Health & Safety and Installation Guides thoroughly before you use this appliance.
- The transit bolts must be removed before the appliance is used.
- See the Health & Safety and Installation Guides for detailed instructions on how to remove the transit bolts
PRODUCT DESCRIPTION
APPLIANCE
- Top
- Detergent dispenser
- Control Panel
- Lid handle
- Door
- Water filter – behind the kick panel
- Removable kick panel
- Adjustable feet (2)
CONTROL PANEL
- On/Off button
- Program selector
- Start/Pause button
- Temperature button
- FreshCare+ button
- Dry Only button / Lock button
- Drying settings button
- Display
- Start delay button
- Spin speed button
DETERGENT DISPENSER
Prewash Compartment
- Detergent for prewash
Main Wash Compartment
- Detergent for the main wash
- Stain remover
- Water softener
Softener compartment
- Softener
- Liquid starch
Pour softener or starch solution into the compartment without exceeding the “max” level.
Release button
(press to remove the tray for cleaning). Preferably use partition A when
washing with a liquid detergent for washing, to ensure that the correct
quantity of detergent is used (the partition is included in the bag containing
the instructions). Move the partition into slot B when using detergent powder.
FIRST TIME USE
See the section DAILY USE for instructions on selecting and starting a program.
FIRST CYCLE OPERATION
Remove any manufacturing debris:
- Select the “Cotton” program with a temperature setting of 60 °C.
- Pour a small quantity of detergent powder into the main wash compartment of the detergent dispenser (maximum 1/3 of the quantity the detergent manufacturer recommends for lightly soiled laundry).
- Start the program without loading the washer-dryer machine (with an empty drum).
DAILY USE
LOADING LAUNDRY.
-
Prepare the laundry, following the recommendations given in the section “HINTS AND
TIPS”. – Open the door and load the laundry into the drum, without exceeding the maximum load capacities indicated in the Programme Chart. -
Close the door, pressing until the latch audibly locks, and check that there is no laundry trapped between the door glass and the rubber seal.
OPEN THE WATER TAP
Check that the washer and dryer are connected correctly to the water mains.
Open the water tap.
SWITCHING ON THE WASHER DRYER MACHINE.
Press the button ; the lamp flashes slowly.
SELECTING A PROGRAMME AND CUSTOMISING A CYCLE.
The following functions are possible with this appliance:
- Wash only
- Wash and dry
- Dry only
Wash only
Select the required program with the PROGRAMME selector dial. The duration of
the wash cycle is shown on the display. The washer-dryer machine automatically
displays the maximum temperature and spin speed settings possible for the
selected programme. Adjust the temperature and/or spin speed settings if
needed with the relative buttons.
- Press the button “Temp” to cycle through progressively lower temperature settings until the cold wash is set (“- -“) shown on display.
- Press the button “Spin speed” to cycle through progressively lower spin speed settings until the spin cycle is turned (“0” shown on display). Pressing the button again sets the highest possible setting. Select the required options (if necessary).
- Press the button to select the option; the respective button lamp illuminates.
- Press the button again to cancel the option; the lamp extinguishes.
- If the selected option is not compatible with the program set, an error warning tone sounds and the indicator lamp ashes three times. The option is not selected.
Wash and dry
To wash and dry a load with no interruption between the wash and dry cycles,
make sure that the load does not exceed the maximum permissible drying load
for the selected program (see the column “Max. load for drying cycle” in the
Programme chart).
- Follow the instructions given in the paragraph “Wash Only” to select and, if necessary, customize the required program.
- Press “Drying settings” to select the required drying mode. Two drying modes are available: automatic or timer.
- Automatic drying with selectable levels: In automatic drying mode, the washer-dryer machine dries the laundry until the set level of dryness is reached. Pressing the button “Drying settings” once automatically selects the highest drying level available for the selected program. Press the button again to reduce the drying level. The following levels are available: Wardrobe : laundry is completely dry and ready to be put away in the wardrobe without ironing. Hanger : laundry is left slightly damp to minimise creasing. Garments must be hung to air dry completely. Iron : garments are left reasonably damp to make ironing easier.
Timer drying mode:
Press the button “Drying settings” repeatedly to set the timer drying mode.
After cycling through all the automatic drying levels, continue pressing the
button “Drying settings” until the desired time is displayed. Values from 210
to 30 minutes are settable. To wash a load of laundry larger than the maximum
permissible load for drying (see the column “Max. load for drying cycle” in
the Programme chart), remove a few garments once the washing cycle has
finished before starting the drying cycle. Proceed as follows:
- Follow the instructions given in the paragraph “Wash Only” to select and, if necessary, customize the required program.
- Do not include a drying cycle.
- Once the washing cycle is finished, open the door and remove a few garments to reduce the load. Now follow the instructions for “Dry only”.
N.B.: always allow a cooling down period after drying before opening the door. When using the two preset cycles “Wash & Dry 45’” and “Wash & Dry 90’”, it is not necessary to select and start a drying cycle.
Dry only
This function is used to simply dry a wet load washed previously in the washer
and dryer or by hand.
- Select a suitable program for the laundry you want to dry (e.g. select cotton to dry wet cotton laundry).
- Press the button “Dry only” to dry without a wash cycle.
- Press “Drying settings” to select the required drying mode. Two drying modes are available: automatic or timer.
Automatic drying with selectable levels:
In automatic drying mode, the washer-dryer machine dries the laundry until the
set level of dryness is reached. Pressing the button “Drying settings” once
automatically selects the highest drying level available for the selected
program. Press the button again to reduce the drying level.
The following levels are available:
- Wardrobe : The laundry is completely dry and ready to be put away in the wardrobe without ironing.
- Hanger : The laundry is left slightly damp to minimize creasing. Garments must be hung to air dry completely.
- Iron : garments are left reasonably damp to make ironing easier.
Timer drying mode:
Press the button “Drying settings” repeatedly to set the timer drying mode.
After cycling through all the automatic drying levels, continue pressing the
button “Drying settings” until the desired time is displayed. Values from 210
to 30 minutes are settable. N.B.: always allow a cooling down period after
drying before opening the door.
USING THE CORRECT AMOUNT OF DETERGENT. Pull out the tray and pour detergent into the relative compartments as described in the “Detergent dispenser”. This is only necessary when using a wash only or a wash + dry program.
DELAYING THE START OF A PROGRAMME. To set a program to start at a later time, see the section “Options and Functions”.
STARTING A PROGRAMME.
Press the START/PAUSE button.
The machine will lock the door ( symbol OFF) and the drum will start to
rotate; the door will be unlocked ( symbol on) and then locked again ( symbol
OFF) as preparation phase of each washing cycle. The “Clicking” noise is part
of the door-locking mechanism. Water will enter the drum and start the washing
phase once the door is locked. To change a program while a cycle is in
progress, press START/PAUSE to pause the WASHER DRYER (the START/ PAUSE lamp
flashes amber slowly); then select the required cycle and press START/PAUSE
again. To open the door while a cycle is in progress, press START/PAUSE; the
door may be opened if the symbol lights. Press the START/PAUSE button again to
resume the program from where it was paused.
CANCELLING A RUNNING PROGRAMME ˜IF NECESSARY°Press and hold the button
until the washer dryer stops.
If the water level and temperature are low enough, the door unlocks and may be
opened.
The door remains locked if there is water in the drum. To unlock the door,
switch the washer dryer on, select the SPIN & DRAIN program and turn the spin
function off by setting the spin speed to 0. The water is emptied and the door
unlocks at the end of the program.
SWITCHING THE WASHER DRYER OFF AT THE END OF A PROGRAM.
At the end of the cycle, the message “END” is shown on the display. The door
can only be opened when the symbol lights. Check that the door unlocked symbol
is lit, then open the door and take out the laundry. Press to switch the
washer and dryer off. To save energy, if the washer and dryer is not switched
off manually with the button, it turns off automatically approximately 10
minutes after the end of the program. Leave the door ajar to let the interior
of the washer dryer dry.
HINTS AND TIPS
Sort your laundry according to the Type of fabric/care label (cotton, mixed fibers, synthetics, wool, handwash items). Color (separate colored and white items, wash new colored items separately). Delicates (wash small items – like nylon stockings – and items with hooks – like bras – in a cloth bag or pillow case with a zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the drum.
Follow the dosage recommendation/additives
It optimizes the cleaning result, avoids irritating residues of surplus
detergent in your laundry and it saves money by avoiding waste of surplus
detergent
Use low temperature and longer duration
The most efficient programs in terms of energy consumption are generally those
that perform at lower temperatures and longer duration.
Observe the load sizes
Load your washing machine up to the capacity indicated in the
“PROGRAMME CHART” table to save water and energy.
Noise and remaining moisture content
They are influenced by the spinning speed: the higher the spinning speed in
the spinning phase, the higher the noise and the lower the remaining moisture
content.
WASH SYMBOLS
ON GARMENT LABELS
The value given in the tub symbol is the maximum temperature possible for
washing the garment.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch off and unplug the washing machine. Do not use flammable fluids to clean the washing machine. Clean and maintain your washing machine periodically (at least 4 times per year).
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine. Do not
use glass or general-purpose cleaners, scouring powder, or similar to clean
the control panel – these substances might damage the printing.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged, replace
it with a new hose available through our After-Sales Service or your
specialist dealer. Depending on the hose type: If the inlet hose has a
transparent coating, periodically check if
the color intensifies locally. If yes, the hose may have a leak and should be
replaced. Cleaning the water ÿlter / draining residual water If you use a hot
wash program, wait until the water has cooled down before draining any water.
Clean the water filter regularly, to avoid the water cannot drain after the
wash due to obstruction of the filter. Remove the plinth by using the
screwdriver: push downwards one side of the plinth with your hand, then push
the screwdriver into the gap between the plinth and front panel and pry open
the plinth. Place a broad, flat container beneath the water filter, to collect
the drain water. Slowly turn the filter counterclockwise until water flows
out. Let the water flow out, without removing the filter. When the container
is full, close the water filter by turning it in clockwise. Empty the
container. Repeat this procedure until all the water has drained. Lay a cotton
cloth beneath the water filter, which can absorb a small amount of rest water.
Then remove the water filter by turning it out anti-clockwise. Clean the water
filter: remove residues in the filter and clean it under running water. Insert
the water filter and reinstall the plinth: Reinsert the water later again by
turning it in a clockwise direction. Make sure to turn it in as far as it
goes; the filter handle must be in a vertical position. To test the water
tightness of the water filter, you can pour about 1 liter of water into the
detergent dispenser. Then reinstall the plinth.
Cleaning the detergent dispenser
Remove the detergent dispenser by pressing the release button and at the same
time pulling out the detergent dispenser. Remove the insert from the detergent
dispenser, as well as the insert of the softener compartment. Clean all parts
under running water, removing all detergent or softener residues. Wipe the
parts dry with a soft cloth. Reinstall the detergent dispenser and push it
back into the detergent compartment.
SAVING ENERGY AND PROTECTING THE ENVIRONMENT
- Keeping within the load limits indicated in the program chart will optimize energy, water, and detergent consumption and reduce washing times.
- Do not exceed the detergent quantities recommended by the detergent manufacturer.
- Save energy by using a 60°C instead of a 90°C wash programme, or by using a 40°C instead of a 60°C wash program. We recommend using the Eco 40-60 program for cotton garments, which is longer but uses less energy.
- To save energy and time when washing and drying, select the highest spin speed available for the program to reduce the residual water remaining in the garments at the end of the wash cycle.
PROGRAMME CHART
The cycle duration indicated on the display or instruction manual is an estimate based on standard conditions. The actual duration may vary in relation to several factors, such as the temperature and pressure of the incoming water, ambient temperature, amount of detergent, load quantity and type, load balancing, and any additional options selected. The values given for programs other than the Eco 40-60 program are indicative only.
-
Eco 40-60 (Wash) – Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most efficient program in terms of energy and water consumption for washing normally soiled cotton laundry.
Note: spin speed values shown on the display can slightly differ from the values stated in the table. -
Eco 40-60 (Wash& Drying)- Test drying cycle in compliance with EU Ecodesign regulation 2019/2014. To access the “wash and dry” cycle select the “Eco 40-60” wash programme and set the option level to “ ”. The most efficient program in terms of energy and water consumption for washing and drying is normally soiled cotton laundry. At the end of the cycle, the garments can be immediately stored in the cupboard.
For all testing institutes:
- Long cotton cycle: set program COTTON at a temperature of 40°C.
- Long synthetics cycle: set cycle SYNTHETICS at a temperature of 40°C.
- Select the SPIN & DRAIN program and set the spin speed to “- -“ to empty only.
- The duration of the wash cycles can be checked on the display.
- After program end and spins with the maximum selectable spin speed, in the default program setting.
- The display will show the suggested spin speed as the default value.
For wash programs with temperatures above 50°C, we recommend using powder detergent rather than liquid and following the directions given on the detergent package. 6th Sense – the sensor technology adapts water, energy, and programme duration to your wash load.
PROGRAMMES
Follow the directions indicated in the garment wash symbols.
MIXED
For washing lightly to normally soiled resilient garments in cotton, linen,
synthetic fibers, and mixed fibers.
WHITE
For washing normally to heavily soiled towels, underwear, table and bed linen,
etc in resilient cotton and linen. Only when the temperature is selected at
90°C the cycle is provided with a prewash phase before the main washing phase.
In this case it is recommended to add detergent both, in the prewash and main
wash sections.
COTTON
for washing normally heavily soiled towels, underwear, tables, bed linen, etc.
in resilient cotton and linen.
ECO 40-60
For washing normally soiled cotton garments declared to be washable at 40 °C
or 60 °C, together in the same cycle. This is the standard cotton program and
the most efficient in terms of water and energy consumption.
DELICATES
for washing particularly delicate garments. Preferably turn garments inside
out before washing.
SYNTHETICS
for washing normally soiled garments made from synthetic fibers (such as
polyester, polyacrylic, viscose, etc.) or cotton/ synthetic blends.
STEAM REFRESH
for refreshing garments, neutralizing unpleasant odors, and relaxing the
fibers by delivering steam into the drum. The garments will be damp at the end
of the cycle.
SPIN & DRAIN
spins the load then empties the water. For resilient garments.
RINSE & SPIN
rinses and then spins. For resilient garments.
RAPID 30′
for washing lightly soiled garments quickly: this cycle lasts only 30 minutes,
saving time and energy. Maximum load 4,5 Kg.
20°C
For washing lightly soiled cotton garments, at a temperature of 20 °C.
WOOL
All wool garments can be washed using the program,”Wool” even those carrying
the “hand-wash only” label. For best results, use special detergents and do
not exceed max kg declaration of laundry.
WASH & DRY 45′
for washing and drying lightly soiled cotton and synthetic fiber garments
quickly. This cycle washes and dries a laundry load of up to 1 Kg in just 45
minutes.
WASH & DRY 90′
for washing and drying cotton and synthetic fire garments quickly. This cycle
washes and dries a laundry load of up to 2 Kg in just 90 minutes.
OPTIONS AND FUNCTIONS
OPTIONS selectable directly by pressing the relative button
- If the selected option is not compatible with the program set, an error warning tone sounds and the indicator lamp flashes three times. The option is not selected.
FRESHCARE+
If associated with wash cycles, this option increases their performances by
generating steam to block the proliferation of the main sources of unpleasant
odours inside the appliance (exclusively for the wash). After the steam phase,
the machine runs a delicate cycle with slow drum rotations. When the
FRESHCARE+ option is associated with drying cycles, it prevents stubborn
creases from stabilizing on garments, thanks to slow drum rotations. The
FreshCare+ cycle starts at the end of the wash or drying cycle and continues
for a maximum of 6 hours; it can be interrupted at any time by pressing any
button on the control panel, or by turning the knob. Wait roughly 5 minutes
before opening the door.
START DELAY
To set the selected program to start at a later time, press the button to set
the desired delay time. The symbol lights on the display when this function is
enabled. To cancel the delayed start, press the button again until the value
“0” is shown on the display.
LOCK BUTTON
to lock the control panel, press and hold the button “Dry only” for
approximately 3 seconds. the symbol lights on the display to indicate that the
control panel is locked (with the exception of the ( button). This prevents
unintentional changes to programs, especially with children near the machine.
If any attempt is made to use the control panel, the symbol flashes on the
display. To unlock the control panel, press and hold the button “Dry only” for
approximately 3 seconds. Regulatory documentation, standard documentation,
ordering spare parts, and other product information can be found:
- By visiting our website docs.whirlpool.eu and parts – self-service.whirlpool.com
- Using QR code
- Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product’s identification plate. For User’s Repair & Maintenance Information visit www.whirlpool.eu
The model information can be retrieved using the QR code reported in the energy label. The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu