baby lock BLMAG Allegro Sewing Machine User Manual

baby lock BLMAG Allegro Sewing Machine

OPEN EXTERNAL COVER

Please follow orcfer as below for disassembling

1. FACE COVER (J) BACK COVER
2. TOPLID
3. TOP COVER
4. BOTTOM PLATE
5. BOTTOM COVER(A)
6. FRONT COVER
7. BACK COVER

COVER REMOVAL

Face Cover

Remove the needle Plate 1

Remove screw “A” and slide Face cover to the left. Caution: Do not to pull too hard as there is an LED light attached.

Carefully slide the LED “B” away from the face cover .

Top Lid

Pull Top Cover straight up

Top Cover

Bottom Plate

Remove 4 screws “E” and detach the bottom base cover.

While attaching the Bottom Cover, be sure the hook on the knee Lifter Linkage is positioned as shown, or the knee life will not engage.

Bottom Cover

Remove screw “F” from the free arm cover at the Rear of machine.

Remove 2 screws “G” and detach the Free Arm Cover.

Front Cover

Remove screw “H” and take away Front Cover.

Rear Cover

Remove screw “I” from the Rear Cover (On the bottom).

Remove screw “J” raise handle, and detach Rear Cover (Above Upper Shaft) Screw “J” is longer than screw “I”

Presser Bar Height

Tool: 2.0mm hexagon screwdriver & 6.0mm height of gauge

Standard: Height of presser foot is 6.0mm

A. Open face cover. (See P4.)
B. Lift presser bar lever to upper position.
C. Loosen hexagon screw (A) of presser bar guide bracket (M986-012).
D. Adjust presser bar (986026-1) until presser foot lifting height is 6.0mm
E. Tighten hexagon screw (A).

CHECK:
Repeat the presser bar lifter down & up for confirm the height of presser foot is 6.0mm.

Height of Feed dog

Tool: 7.5mm nut driver, flathead screwdriver and gauge measurement for height of feed dog.
Standard: Height of Feed dog is 0.9mm when it starts to move ~height of feed dog moves to highest position 1.1mm.

Adjustment:

A. Turn hand wheel to make needle rising to highest position.
B. Open bottom cover.
C. Use flathead screwdriver and turn the feed lifting regulate screw (829023) clockwise until feed dog is raised to standard height when feed dog is lower than 0.9mm.
D. Use flathead screwdriver and turn the feed lifting regulate screw (829023) counter-clockwise until feed dog is lowered to standard height when feed dog is higher than 1.1 mm.
E. Use Nut driver to tighten the hexagon nut. (000010003).

Transmission of Feed dog

Tool: 2.5mm hexagon screwdriver.
Standard: Transmission of Feed dog is in between 0-1mm when needle is moved down from highest position.

Check:
Turn hand wheel to move needle to highest position, and check transmission of feed dog.

Adjustment

A. Open front cover.
B. When transmission is too early, use 2.5mm hexagon screwdriver to loosen the hexagon screw (A) of feed cam (C168-041), and keep screwdriver in the screw as a handle to move the cam up for adjusting it to standard position mark on the shaft.
C. When transmission is too late, use 2.5mm hexagon screwdriver to loosen the hexagon screw (A) of feed cam (C168-041), and keep screwdriver in the screw as a handle to move the cam down for adjusting it to standard position mark on the shaft.
D. Use 2.5mm hexagon screwdriver to tighten the hexagon screw of feed cam (C168-041).
E. FEED TIMING : When the needle is at it’s highest position, The Feed dog will start to advance to the back at the same time the needle starts to drop down.

Needle drop (center) position

Tool: 2.0mm hexagon screwdriver and flathead screwdriver.
Standard: 3.5 mm each side in the needle plate hole when Needle position is in the center of needle plate hole.
Requirement of Adjustment: Select stitch No. 006 zigzag as adjusting sample pattern, and needle will stop in right position.

Check:

A. Open front cover.
B. Adjust stitch width to 3.5. (Needle is in the center)
C. Turn manually hand wheel to make needle lower into needle plate hole, and check the distance between needle and right side/left side in the needle plate hole.

Adjustment

A. Use 2.0mm hexagon screwdriver, and loosen the hexagon screw (A) of needle bar crank.
B. Use flathead screwdriver to adjust zigzag eccentric pin until the needle is in right correct position:

• When you turn it clockwise the needle is moved to right side.
• When you turn it counter-clockwise the needle is moved to left side.

C. Tighten and secure the hexagon screw (A) of needle bar crank when position is set.
-Hexagon screw (A)-000079103(4×4)
-Needle bar cradle (986052-2)

Installation of Bobbin case

Tool: Phillips screwdriver.
Standard: Distance is 1mm between bobbin case and stop shrapnel holder (M986-154/730152)

Adjustment:

A. Open needle plate
B. Loosen screw (A) of Stop shrapnel holder (M986-154).
C. Tighten screw (A) of Stop shrapnel holder (M986-154) and install needle plate back.
D. Check bobbin case has 1mm gap with stop shrapnel holder (M986-154/730152)

Timing of rotary hook.

Tool: 2.5mm hexagon screwdriver and a specialized gauge of measurement.
Standard: The needle is required to be at a proper position with rotary shuttle hook tip

Check:

A. Set Pattern No. at 002 (straight stitch in left position) or adjust stitch width to “0” for left needle position when pattern No. 006 is set.
B. Open Needle plate, and take bobbin case off.
C. Turn hand wheel by clockwise to make the needle raising from the bottom of shuttle race to correct position with shuttle hook tip as below figure shown.
D. Check relevant position between Needle hole and rotary shuttle hook tip.

Adjustment:

A. Open bottom cover
B. Use 2.5mm screwdriver, loosen the hexagon screw (A),(B) of lower shaft gear
C. When shuttle hook moves exceeding needle hole position 2.5mm screwdriver can be used as a handle with screw (A) to move gear down until the hook tip reaches correct position with needle.
D. When shuttle hook moves before needle hole position 2.5mm screwdriver can be used as a handle with screw (A) to move gear up until the hook tip reaches correct position with needle.
E. Tighten the hexagon screw (A) (B) of lower shaft gear.
Note: 2 pcs of hexagon screws (A) & (B) must be secured and tightened.

Needle bar height

Tool: 2.0mm hexagon screwdriver, flathead screwdriver.
Standard: Sharp point of needle is lowered to touch bottom surface of rotary hook.
Note: Needle must be inserted and against the pin in the top and hold.
Tighten the needle clamp screw for fixing the needle.

CHECK:

A. Open needle plate, take bobbin case out.
B. Turn the hand wheel counter-clockwise to lower needle to lowest position.
C. Check the distance between needle and bottom surface of rotary hook. (See below figure.)
Note: The needle sharp touches bottom surface of hook gently.

Adjustment:

A. Loosen the hexagon screw (A) of needle bar rod link (281045004), and adjust its position to Up or Down
until needle is in correct position.
B. Tighten the hexagon screw of needle bar rod link (281045004)

Needle clearance in rotary hook

Tool: 2.0mm hexagon screwdriver.
Standard: The distance between needle(HA-1 #14) and rotary shuttle sharp hook is 0.05～0.1mm
Check:
Move needle position to center by setting stitch width at 「 3.5 」.

Adjustment:

A. Open face cover
B. Use 2.0mm hexagon screwdriver and loosen the hexagon socket screw (A) (00079103)
C. When the distance is too close, move needle bar cradle (986052-2) forth until distance is correct.
D. When the distance is too far, move needle bar cradle (986052-2) back until distance is correct.
E. Hexagon socket screw (A) (00079103) must be tightened and secured.
F. Loosen screw (B) and hold, and move needle bar lead base (986057) to left or right for balancing needle position at left-middle-right of hook, and tighten the screw (B) for securing the lead base.
※ If unbalance distance between Needle and hook is found, you may follow step F for adjusting

Upper Tension Dial

Tool: Tension meter
Standard: Tension range is 40g when Tension dial is set at level 4

Check:

A. Set Tension Dial at level 4.
B. Lift presser bar
C. Threading the thread with tension meter
D. Lower presser bar.
E. Pull the thread with the meter for measuring

Adjustment:

A. Open front cover.
B. When tension is too tight (More than 40g at level 4), turn tension regulator (A) down manually until standard tension value.
C. When tension is too loose (less than 35g at level 4), turn tension regulator (A) up manually until standard tension value.

Tension of Bobbin case

Tool: Tension meter and small flathead screwdriver.
Standard: Tension range is 13-14g with 50w Madeira thread
ACheck: . Open needle plate, and take bobbin case off.

Adjustment:

A. When tension is too tight use small flathead screwdriver to turn the regulating screw (A) counterclockwise until standard tension value.
B. When tension is too loose use small flathead screwdriver to turn the regulating screw (A) clockwise until standard tension value.
C. Install needle plate and bobbin case when regulating is finished.

Auto Needle threader

Tool: 1.5 mm hexagon screwdriver and flathead screwdriver
Standard: Hook of Auto needle threader is correctly into needle eye to get thread through it/.

Check:

A. Turn hand wheel to make needle raising to highest position.
B. Check thread can be hooked well from needle eye when threader is used.

Adjustment:

A. Open face cover.
B. Use 1.5mm hexagon screwdriver to loosen hexagon screw (A) of through thread location plate (270017003), and keep screwdriver in the hexagon screw hole.
C. When the hook of threader is lower than needle eye hexagon screwdriver is used to move up the location plate until correct position.
D. When the hook of threader is higher than needle eye hexagon screwdriver is used to presser down the location plate until correct position.
E. Check whole threading process when auto threader is used.
F. Tighten the hexagon screw(A) of through thread location plate(270017003).

Timing of take–up lever Covers

Tool: 1.5 mm hexagon screwdriver.
Standard: Timing of take-up lever

Check:

A. Turn hand wheel counter–clockwise, and make sure the take-up lever is over thread guide plate(M986-
122) about 1.0-1.2mm high while the needle is at highest position.

Adjustment:

A. Open face cover and top cover.
B. Use 1.5mm hexagon screwdriver, loosen hexagon screw(A) of upper positioning cam (M986-147).
C. Turn hand wheel to make take-up lever in correct position.
D. Tighten hexagon socket screw 4*3 (000079705) to make upper positioning cam in correct position when take-up lever is in correct position.
E. Turn power on, and press needle up/down button for checking.

Check starting point & Calibrate Pattern

Check:

1. Power of machine is turned on.
2. Stepping motor will senses the start point when needle position is tuned to Upper or lower.

Problem 1:

Stepping motor doesn’t have motion to sense the starting point or starting point is off standard position.
Solution: Change PC-3 (14K15M) Main circuit board or Stepping Motors (128082)
Refer to Page 23 for adjusting start point.

Problem 2: Pattern is sewn differently from standard.
The pattern is shown different from standard after sewing as below similar situation

Ex 1.

 Pattern No. 094 is sewn as left standard

diagram   is wider

a. Use Philip screwdriver to loosen screw (A)
b. Adjust screw (B) by count-clockwise
c. Tighten screw (A) before test
d. Secure screw (A) well if sewing test is ok.

When is closer

a. Use Philip screwdriver to loosen screw (A)
b. Adjust screw (B) by clockwise
c. Tighten screw (A) before test
d. Secure screw (A) well if sewing test is ok.

Installation of Bobbin Thread cut Mechanism

Tool: Phillips and Flathead screwdriver.
Standard: Installation and Adjustment of Bobbin Thread cut Mechanism

Check:

A.Timing of take-up lever when needle position is turned to upper position.(P.21)
B. MD-004 & MD-005 Thread cutting clamping plate is not touched feed dog and bobbin case.

• Push thread cut button, then switch power off right the way.
• Turn bobbin case (M986-142) to right against bobbin case stop shrapnel(730152),then hold the bobbin case still, check positon of Thread cutting clamping plate between feed dog and bobbin case.
• Switch power on, the thread cut device is activated to make Thread cutting clamping plate back start position.

C. Hook of MD-005 Thread cutting clamping plate(C) is in proper cutting range with bobbin case.
Check A. Please refer to P21. Timing of take–up lever.
Check B. Distance of Thread cutting clamping plate

Check C. MD-005 Thread cutting clamping plate in right cutting range

Point of hook is higher as left position, bobbin thread may not cut

Point of hook is lower as left position, upper thread may not cut

Adjustment:

1. Release flat head screw 4×8 (000081407) and black slotted screw (M986-068), and, adjust it forward or backward for checking position and distance of Thread cutting clamping plate between feed dog and bobbin case. (Check B).

Installation of Bobbin Thread cut Mechanism

Adjustment:

2. Adjust hook of MD-005 Thread cutting clamping plate(C) in proper range (Check C)
   (a) Take bobbin case off the position. (Refer to P17)
   (b) Push thread cut button, then switch power off right the way, the thread cutting clamping plate will be stayed at area of shuttle hook.
   (C) Use flat head screw driver to hold position A and adjust hook of cutting clamping plate upward or downward until it is in correct position (refer to Check C)

3. Stepping motor changing (128131003) Release 2 screws (000082305 Flat head screw 3×5) for replacement of motor

4. Blade changing

   • Release 2 screws (000082305 Flat head screw 3×5), take MD-003 Thread cutting clamping plate(A) & MD-007 Thread cutting clamping plate latch) off the position, and take blade out.
     

   • nsert new blade from back side of unit, make sure the blade is well clipped and in right position.

   • Secure MD-003 Thread cutting clamping plate(A) & MD-007 Thread cutting clamping plate latch back to position.

   • Make sure MD-003 Thread cutting clamping plate(A) is in correct position between MD-004 Thread cutting clamping plate(B) & MD-005 Thread cutting clamping plate(C).
     

Check position of blade and slide Thread cutting clamping plate is smooth manually.

Change feeding stepping motor (128082)

1. . Open bottom cover

2. Loosen the hexagon socket screw (A) on feed regulating crank (M986-013), and release feed regulating et after 4 screws (C) being loosened, then complete set of feeding regulating unit can be taken off the Arm bed.

3. Loosen the hexagon socket screw of motor gear (A) and 2 screws of stepping motor, and then replace new one.
   Note: Motor gear must be secured well when new motor is replaced with feeding motor plate.
   S. Starting point regulating
   (1) Place feeding regulating gear (FA-057) to grip motor gear (C168-003) together, and count 5th
   teeth starting from position of starting pole when motor gear is moved to touch against starting pole, and grip 2 teeth of the feeding regulating gear(FA-057), then secure the hexagon socket screw (A) of motor gear.

4. Make sure the feeding regulating unit is secured on the Arm bed with 4 screws (C).

Check:

1. Switch power on, and sew letter of A, B, 9 and 0 for testing starting point.
2. If sewing result is different or a little regulating please refer to page 22.
   
   

Auto Buttonhole adjustment

Problem 1: buttonhole presser foot is not sensed when you select button pattern and pull buttonhole lever
down.
Solution:

1. Open face cover
2. Loosen the screw of buttonhole switch case (128024), then adjust and move the switch case backward, tighten screw and test.

Check:

1. Select buttonhole pattern
2. Pull down buttonhole lever while the sign of lever doesn’t flash on the LCD display.
3. Start to sew complete buttonhole

Problem 2. The shape of buttonhole is sew like , this situation is BH switch is backward too far. Solution: Loosen the screw of buttonhole switch case (128024), then adjust and move the switch case forward, tighten screw and test.

Check:

Select buttonhole pattern

2. Pull down buttonhole lever while the sign of lever doesn’t flash on the LCD display.
3. Start to sew complete buttonhole

BH switch case (128024)

Replace of touch board

Tool: Philips screwdriver
Disassembling: Loosen 4 screws, and take main board off first

※Note:

1. Mind the pins and connecting socket on the touch board (20K36T)-Ref. blue mark, when you disassemble and assemble main board.
2. Mind the direction of 4 Pcs of Space blocks (L800-168) when you assemble touch board.

(1) 4 pcs of screws need to be loosened.

(1) Pins on the main board
(2)Connecting socket on the touch board.

(1) 4 pcs of spacer before assembling main board.

Motor belt adjustment

Problem:

1. When the tension of belt is loose the machine doesn’t run properly.

Solution:

1. Loosen screw (A) for releasing the bracket of motor.
2. Bracket of motor can be moved downward or Upward until belt is in proper tension.
3. After adjusting tension, hold the position of motor and use Philip screwdriver to tighten screw (A) for securing bracket of motor.

Technical Update

BLMAG Allegro, Straight Stitch Needle Plate Correction

Thread nesting while using the Straight Stitch Needle Plate on the Baby Lock Allegro could be caused by the Bobbin Case retention bracket on the bottom side of the plate not being at the proper angle. Customers should bring the Needle Plate in for this adjustment and can use their standard plate until the work can be performed.
To correct the problem, from the underneath side of the plate, reform the retention bracket to the left and ensure that it is sitting with a 90-degree angle aligned just to the left edge of the needle plate opening. It should not interfere with the feed dogs.
If using a pair of pliers to make the adjustment, ensure that the needle plate doesn’t get scratched and cause burs.

**Inaccurate

**

Accurate

Documents / Resources

| baby lock BLMAG Allegro Sewing Machine [pdf] User Manual
BLMAG Allegro Sewing Machine, BLMAG, Allegro Sewing Machine, Sewing Machine, Machine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>