ANALOG WAY Zenith 100 Multi Screen and Multi Layer User Guide
- June 13, 2024
- ANALOG WAY
Table of Contents
- THANK YOU
- QUICK SETUP & OPERATION
- ZENITH 100 – REF. ZEN100 / FRONT & REAR PANELS DESCRIPTION
- OPERATION OVERVIEW
- WEB RCS – INSPIRED BY LIVEPREMIER
- START IP STREAMING
- WARRANTY AND SERVICE
- GOING FURTHER WITH THE ZENITH 100
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ANALOG WAY Zenith 100 Multi Screen and Multi Layer
THANK YOU
Thank you for choosing Analog Way and the Zenith 100. By following these
simple steps, you will be able to set up and use your 4K60 multi-layer video
mixer and seamless presentation switcher within minutes.
Discover the Zenith 100 capabilities and intuitive interface while configuring
your first show and unleash your creativity for a new experience in show and
event management
-
1 x Zenith 100 (ZEN100)
-
1 x Power supply cord
-
1 x Ethernet cross cable (for device control)
-
1 x Web-based Remote Control Software included and hosted on the device
-
1 x Rack mount kit (the parts are stowed in the packaging foam)
-
1 x Quick start guide (PDF version)*
-
User Manual and quick start guide are also available on www.analogway.com
CAUTION!
Damage caused by improper rack mounting will not be covered under warranty
QUICK SETUP & OPERATION
Use the Web RCS
The Zenith 100 uses standard ethernet LAN networking. To access the Web RCS,
connect a computer to the Zenith 100 using the Ethernet cable. Then on the
computer, open an internet browser (Google Chrome is recommended).
Into this internet browser, enter the IP address of the Zenith 100 displayed
on the front panel screen (192.168.2.140 by default).
The connection starts.
Often, computers are set to DHCP client (automatic
IP detection) mode. You may need to change the
IP address configuration on your computer before you can connect. These
settings are found in the properties for your LAN network adaptor, and vary by
operating system.
The default IP address on the Zenith 100 is 192.168.2.140 with a netmask of
255.255.255.0.
Therefore, you can assign your computer a static IP address of 192.168.2.100
and a netmask of 255.255.255.0 and should be able to connect.
If the connection is not starting:
- Be sure the computer IP address is on the same network and subnet as the Zenith 100.
- Be sure that two devices do not have the same IP address (preventing IP conflicts)
- Check your network cable. You will need a crossover ethernet cable if you are connecting directly from the Zenith 100 to the computer. If a hub or switch is involved, use straight ethernet cables.
Reset the device to default values
To reset the unit to factory settings to get started.
Use the scroll knob and go to Control > Reset to default values > Yes
Firmware update
1. Download the latest Alta 4K firmware on
www.analogway.com.
2. Put the updater file on a USB drive.
3. Connect the USB drive on the front panel.
4. The updater file is automatically detected.
Otherwise, go to Control > USB Host > Scan for Updater.
4. Extract the updater file.
5. Install the new firmware.
ZENITH 100 – REF. ZEN100 / FRONT & REAR PANELS DESCRIPTION
CAUTION:
The user should avoid disconnecting the power source (AC input) until the unit
is in stand-by mode.
OPERATION OVERVIEW
WEB RCS MENUS
LIVE
Screens / Aux.: Set Screens and Aux Screens layer settings (content,
size, position, borders, transitions, etc.).
Multiviewer: Set Multiviewer widgets settings (content, size, and
position).
SETUP
Preconfig.: Setup assistant for adjusting all basic setups.
Multiviewer: Set Multiviewer signal settings (Custom resolution , rate
and HDR conversion), patterns or image adjustment. Outputs: Set Outputs
signal settings (HDCP, custom resolution and rate), patterns or image
adjustment.
Inputs: Set Inputs signal settings (resolution, rate and HDR conversion),
patterns, image adjustment, cropping and keying.
Images & Library: Import images in the unit. Then load them as image
presets to be used in layers.
Formats: Create and manage up to 16 custom formats.
EDID: Create and manage EDIDs.
Custom LUT: Import and manage LUTs.
Audio: Manage Dante Audio and audio routing.
Extras: Timers and GPIO.
Streaming: Broadcast a video signal over IP to an online web service or
to a private network.
PRECONFIG
System
Set the Internal rate, Framelock, HDR, Audio rate, etc.
Screens / Aux Screns
Enable Screens and Aux Screens.
Select the layer mode per screen (see below). Assign outputs and layers to
Screens using drag and drop.
Mixer Seamless and Split layers mode
In Split layers mode, double the number of layers displayed on Program.
(Transitions are limited to Fade or Cut. Multiviewer widgets display Preview
in wireframe only).
Canvas
Position the outputs in a virtual screen to create the Canvas.
- Set Outputs resolution and position.
- Set Blending or Gap.
- Set Area of Interest (AOI).
Backgrounds
Select allowed Inputs and Images to create up to 8 Background sets per Screen
to be used in Live.
Audio
De-embed audio channels from all inputs and re-embed them on all outputs.
Quick preset
Hide all contents an load a Master Memory, Fade-to-Black or one custom image
on all Screens
LIVE
Create presets in LIVE > Screens and LIVE > Multiviewer.
- Set layer size and position in Preview or Program by clicking and dragging the layer.
- Drag sources into layers from the left panel or select them in layer properties.
- Set transitions and use the Take button to send the Preview configuration to Program
For more layers settings, please refer to the Alta 4K User Manual.
A Multiviewer can display up to 27 resizeable Widgets that act like Screen layers. A Widget content can be an output, preview, input, image or timer.
MEMORIES
Once a preset is built, save it as one of the 200 Screen memory slots (or 50 Master memory slots) the Zenith 100 offers.
-
Click Save, filter what to save and select a Memory.
-
Load a preset at any time on Program or Preview by clicking on the preset number or using drag and drop the preset into the Program or Preview windows.
MORE FEATURES
Save / Load a configuration
Export and Import configurations from the Web RCS or Front panel.
Save configurations directly in the unit.
Image Capture
Create an image file from any input or output video signal.
Keying
Apply Chroma or Luma Keying on an Input.
Master Memories
Use Master Memory to load multiple Screen presets
Remote Control
Fully compatible with Analog Way RC400T, Shot Box² and Control Box3, use them
to recall Memories and trigger transitions.
For complete details and operations procedures, please refer to the Alta 4K User Manual and our website: www.analogway.com
WEB RCS – INSPIRED BY LIVEPREMIER
Familiar to LivePremier and Midra™ 4K users, the Web RCS for Alta 4K is the easiest way to setup your configuration and manage your live presentation.
The Web RCS for Alta 4K is embedded in the device and requires no software installation.
START IP STREAMING
The duplicate of one input or output video signal can be broadcast over IP to an online web service or to a private network.
- Go to Streaming.
- In Configuration, select Client or Server mode. In Client mode, select an RTMP destination.
- In Video > Source, select the Input, Output or Multiviewer source to stream.
- In Video > Profile, select the output format (720p25, 720p30, 720p50, 720p60 or 1080p20 and 1080p30).
- In Video > Quality, select Low, Medium or High. Or select Custom Bitrate and enter a value in kbps.
- In Audio > Mode, select to Follow content or select Direct routing and set the audio source.
- On the top of the page, click Start.
In Server mode, the default URL to get the stream content is: rtmp://192.168.2.140:1935/stream/live
WARRANTY AND SERVICE
This Analog Way product has a 3 year warranty on parts and labor (back to factory). Broken connectors are not covered by warranty. This warranty does not include faults resulting from user negligence, special modifications, electrical surges, abuse (drop/crush), and/or other unusual damage. In the unlikely event of a malfunction, please contact your local Analog Way office for service.
GOING FURTHER WITH THE ZENITH 100
For complete details and operations procedures, please refer to the Alta 4K unit User Manual and our website for further information: www.analogway.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>