DECORFLAME QC111 Electric Stove Heater Instruction Manual

DECORFLAME QC111 Electric Stove Heater

Product Information

The Electric Stove Heater is a portable heating appliance designed to provide warmth and ambiance to your living space. It features a realistic flame effect and can be used as a decorative element in addition to its heating function. The heater operates on a 15 AMP circuit and requires a power outlet to function.

Safety Instructions

When using the Electric Stove Heater, it is important to follow these safety guidelines to reduce the risk of fire, electric shock, and injury:

1. Read all instructions before using this heater.
2. Avoid direct skin contact with hot surfaces. Use handles if provided when moving the heater.
3. Keep combustible materials at least 3 feet away from the front, sides, and rear of the heater.
4. Exercise caution when using the heater around children, invalids, and when leaving it unattended.
5. Always unplug the heater when not in use.
6. Do not use the heater outdoors.
7. Avoid using the heater in bathrooms, laundry areas, or similar locations where water contact is possible.
8. Avoid running the cord under carpeting or covering it with throw rugs. Keep the cord away from traffic areas.
9. To disconnect the heater, turn off the controls and remove the plug from the outlet.
10. Avoid inserting foreign objects into ventilation or exhaust openings.
11. Ensure proper airflow by not blocking air intakes or exhaust openings.
12. Avoid using the heater in areas where flammable liquids are used or stored.
13. Use the heater only as described in the manual to prevent fire, electric shock, or injury.
14. Avoid using an extension cord. If necessary, use a minimum No.14 AWG cord rated not less than 1875 watts.
15. Do not plug the heater into a receptacle controlled by a wall switch or dimmer.
16. Store the unit and cord in a dry place, free from excessive vibration, and to prevent damage.

It is important to save these instructions for future reference.
Note : When first turned on, the stove may emit a slight harmless odor. This is normal and should not occur again.
If the breaker trips when using the heater, consider moving it to another location or unplugging other appliances on the same circuit. If an extension cord is necessary, use one rated at 1875 watts or higher.

ATTENTION:

1. Find a location for the stove heater that is protected from direct sunlight.
2. Do not plug the unit into the power outlet before reading all instructions.

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:

1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or is damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
8. Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Arrange the cord away from the traffic area and where it will not be tripped over.
9. To disconnect the heater, turn the controls to off, then remove the plug from the outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
14. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No.14 AWG minimum size and rated not less than 1875 watts.
15. Do not plug this product into a receptacle controlled by a wall switch or dimmer.
16. When storing or transporting the unit and cord, keep in a dry place, free from excessive vibration and store to avoid damage.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

NOTE : The stove may emit a slight harmless odor when first turned on. This is caused by activating the internal heater components for the first time and should not occur again.
A 15 AMP circuit is required to operate this heater. If the breaker trips when the heater is used then you may need to move the heater to another location or unplug other appliances that are on the same circuit. If you require an extension cord use one that is rated at 1875 watts.
IMPORTANT
Please note: When you open the carton care-fully check the unit and make sure there is no damage. If you have any problems with the unit, with how the various functions work, damaged or missing parts please call 1-800-459-4409 (9am to 5 pm EST) immediately for service.
NOTE : DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER
Do not dispose of your cartons until you are completely satisfied with your new stove heater.
NOTE : Light bulbs may become loose during shipping. If the flame effect is dim or does not work, please check that light bulb or bulbs are finger tight in socket. See instructions for replacing bulb or bulbs. Please do not return the sample to the store before checking light bulbs.

LEG ASSEMBLY

Before using your unit please install the legs as shown in diagram below.

OPERATION

After completely reading instructions, confirm that all controls on stove are in the off position. Plug the unit into a 15 amp, 120 volt outlet.

OPERATION

Controls and switches are located on front panel inside the glass door.

• FLAME: Press this button into the I position for main power and flame effect. The indicator light will turn on. See below for other control switches.
• HEATING: For low heat function – Press this switch while the FLAME switch is in the I position for low heat. The indicator light will turn on.
• TURBO: For high heat function – Press this switch while the FLAME and HEATING switches are in the I position for high heat. The indicator light will turn on.
• THERMOSTAT: To adjust the temperature to your individual requirements. Turn the thermo-stat dial to the right (clockwise) to increase the desired temperature and to the left for lower temperature. This thermostat control dial can only be used while the FLAME switch and HEATING/TURBO switches are in the I position.
• When the heater reaches the desired tempera-ture, the heater and Heating /Turbo indicator light will turn off but the fan will continue to operate. Adjust this knob to restart the heater.

FLAME INTENSITY : Turn the dimmer dial clockwise or counter clockwise to get the desired flame intensity. The dimmer switch can only be used when the FLAME switch is in the I position.
NOTE : When the FLAME switch is turned in O position, all other heater functions will stop even though the switches may be in the I position.

THERMOSTAT CONTROL

The heat output is controlled by the thermostat, according to the room temperature. Set the thermostat dial fully clockwise to the maximum position initially.
When the room is warm enough, reduce the setting by slowly turning the thermostat dial anticlockwise until the heater just clicks off. This will then maintain the room temperature at the desired level.

CAUTION

If you use this heater in conjunction with a thermal control, a program controller, a timer or any other device that switches on the heater automatically, remember to observe all safety warnings at all times.
The stove heater has a safety overheat protec-tion. If the overheat protection trips, turn off the FLAME switch and unplug the power cord from the receptacle. It should reset automatically after 5 minutes.

WARNING
Disconnect power and unplug the power cord before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or personal injury. The bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the unit and removing the light bulbs to avoid the accidental burning of the skin.

FLAME EFFECT

• The fire effect is created with the use of a 40-watt B-10 candelabra light bulb with an E-12 (small) socket base. The light bulb will have to be replaced from time to time when they burn out.
• During normal operation, the stove heater will always give you a simulated flame function. If the intensity of flame suddenly increases, it means that the light bulb is going to burn out.
• Replace the light bulb immediately according to the instructions and do not operate the stove heater when the light bulb burns out or without the light bulb.

CHANGING THE LIGHT BULB

• STEP 1: Open the door of the unit with the handle.
• STEP 2: Loosen the 2 screws at the front of the log set inside the stove. Carefully lift the log set up far enough to access the light bulbs. You will find 1 X 40W Type B-10 candelabra light bulb with E-12 socket base at the bottom.
• STEP 3: Replace the burned-out light bulb using a new 40-watt Type B-10 candelabra light bulb.
• STEP 4: Reinstall the log set.
• STEP 5: Plug in the unit.

CLEANING / WARRANTY

CLEANING

• To clean the unit first turn off the controls on unit and unplug the unit from the power source.
• To clean glass door; remove dust with clean dry cloth or to remove finger prints and other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray liquids on glass door surfaces.
• Metal and metal-painted parts should be cleaned with damp cloth. Do not use abrasive cleaners or spray liquids on these surfaces.

WARRANTY

Every electric stove is tested before it leaves the factory and it is guaranteed for one year. If the unit should fail to operate correctly within one year from the date of purchase, call customer service at 1-800-459-4409 EST. We will, at our discretion either repair or replace the unit. It will have to be returned to us freight prepaid and we will return the repaired or replaced unit to you freight prepaid. The company’s sole obligation is to repair or replace the unit.This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source. Light bulbs are not covered by this warranty. The warranty is for homeowner use only and does not cover units used in commercial situations.

IMPORTED BY
Quality Craft Ltd Laval, Quebec, Canada H7S 2G7 1-800-459-4409
www.qualitycraft.com
Made in China

References

• Quality Craft
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>