Altronix Trove1V1R Power Integration Enclosure with Backplane Installation Guide

Altronix Trove1V1R Power Integration Enclosure with Backplane

Product Information

Product Name: Trove1V1R

Specifications

• Backplane Accommodates a Combination of the Following: Altronix Hardware and Accessories
• Agency Listings: UL Listed tamper switch (Altronix Model TS112 or equivalent)

Hardware and Accessories

• Spacer
• 7/8 Pan Head Screw
• Lock Nut
• Z Bracket Wire Management Accessory (included)

Product Usage Instructions:

1. Remove the backplane from the enclosure prior to installing it into the rack cabinet. Make sure not to discard the hardware.
2. Mount the included UL Listed tamper switch (Altronix Model TS112 or equivalent) by turning the enclosure upside down and punching out the knockout in the designated location on the back of the unit. Insert the tamper switch into the knockout with the button facing outwards and spaded connectors inside the drawer. Connect the tamper switch wiring to the Access Control Panel inputor the appropriate UL Listed reporting device.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Attach the front ears of the enclosure to the rack rails using proper fasteners.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet using proper fasteners.
6. Secure the rack cover and rack drawer to earth ground.
7. Ensure that all internal configurations (wiring, voltage selection, switch settings, etc.) are complete before mounting the backplane back into the enclosure.
8. After all components are mounted on the backplane, attach it to the enclosure using the included hardware.
9. To assemble and attach the Z Bracket Wire Management Accessory:
   • Carefully unpack the Z Bracket and do not discard the included hardware.
   • Attach the arms of the Z Bracket to each other using bolts and lock nuts.
   • Attach the hinge brackets to the ends of the arms using bolts and nuts, positioning them as shown.
   • Make sure that all nuts are tightened.
   • Attach the hinge bracket on the longer side of the Z Bracket to the adjustable slide using bolts and lock nuts.
   • Attach the hinge bracket on the shorter side of the Z Bracket to the rear of the rack enclosure using bolts.

Overview

Altronix Trove1V1R rack mount access & power integration solution accommodates various combinations of HID VertX® boards with or without Altronix power supplies and accessories for access systems.

Specifications

Agency Listings:

• CE European Conformity.

Trove1V1R

Trove1R rack mount enclosure with TVR Altronix/HID VertX® backplane.

• 16 Gauge black enclosure with ample knockouts for convenient access.
• Modular 2U standard EIA 19” drawer with extendable slides up to 48”.
• Dimensions (H x W x D): 3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm).
• Includes tamper switch (Altronix Model TS112 or equivalent) and cam lock.

TV1R

Altronix/HID VertX® backplane.

• 16 Gauge backplane.
• Dimensions (H x W x D): 18.5” x 15.25” x 0.3125” (469.9mm x 387.4mm x 7.9mm).

Optional Accessories

• RE2: Rack Mount Battery Enclosure accommodates up to four (4) 12VDC/7AH batteries
• WM5, WM25, WM100: Magnetic Cable Tie Mounts (5, 25, 100 counts).
• LC3: 6 ft. three-wire line cord.

Backplane Accommodates a Combination of the Following:

Altronix:

• Up to two (2) eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB, ACMS8(CB) or ACM8(CB).
• Up to three (3) ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6.

HID VertX®

• Up to six (6) V100, V200, V300, V1000 or V2000.

Hardware and Accessories

Installing Trove1R into Rack Tower

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. These products are for indoor use only and must be installed within the protected premises.

Note: First assemble and Install Z Bracket Wire Management Accesory (refer to Z Bracket Installation)

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down. Punch out the knockout in designated location, on the back of the unit, from outside of the drawer (Fig. 1,). Insert the tamper switch into the knockout from outside of the drawer with the button facing outwards and spaded connectors inside the drawer.
   • Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
   • To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a,) and rack drawer to earth ground (Fig. 2b,).
7. Make sure that all internal configurations (wiring, voltage selection, switch settings, etc.) are complete before mounting backplane back into enclosure.
8. After all components are mounted on the backplane, attach it to the enclosure using included hardware.

Assembling and Attaching

Z Bracket Wire Management Accessory (included):

Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.

Hardware (included):

1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 3,).
2. Attach arms to each other using bolts and lock nuts (Fig. 3a,).
3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on (Fig. 3b,).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts (included) (Fig. 4, 4a,).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

TV1R

Configuration of Altronix Power Supply and/or Sub-Assembly Boards

1. Fasten spacers onto metal pems configuration (A) or (B) of backplane depending on the board (Fig. 5,).
2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 5a,).
3. Mount backplane to enclosure with hardware.

Position Chart for the Following Models:

TV1R

Configuration of HID VertX® Boards

1. Fasten spacers onto metal pems configuration (A) of backplane (Fig. 6,).
2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 6a,).
3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Dimensions

Trove1R Enclosure Dimensions:

3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.

Altronix is not responsible for any typographical errors.

Contacts

• 140 58th Street, Brooklyn, New York 11220 USA
• phone: 718-567-8181
• fax: 718-567-9056
• website: www.altronix.com
• e-mail: info@altronix.com
• Lifetime Warranty

1. Installing Company: ____
2. Service Rep. Name: __
3. Address: ___
4. Phone #: __

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>