Shenzhen Huanyu Baijia Technology AS1 Wireless Charging Smart Watch Instruction Manual
- June 13, 2024
- Shenzhen Huanyu Baijia Technology
Table of Contents
Smart Watch Wireless Charging
PRODUCT SPECIFICATIONS
For Apple Watch Charger
Charger Color· white Material: Aluminium alloy+ PC
Current: 1A
Output: 2.SW
Operating Temperature: -1 o·c-so’C
Ambient Humidity: 35% -85%
Feature
- Lightning Port+ TypeC Port
- Quick Charger(For a better charging experience, it is recommended to use 5V/2Aadapter or above)
- Compatible with Apple Watch Series 8/7/6/ 5/4/3/2/1/SE/Ultra
- Compatible with Apple Watch 38mm/40mm/ 41 mm/42mm/44mm/45mm/49mm
- Strong Magnetic Suction- Build in latest magnetic adsorption module, charge immediately after contact
- Portable Mini Size & Charge on the go, Small and compact wireless charger for your watch, it is easier to take anywhere
PLEASE NOTE:
Please connect the wireless charger to the original power adapter with an
output of 5V/2A or above, and the charging effect will be faster; Do not use
the charger with electronic products that do not meet the specifications, so
as not to cause any problems due to mismatched specifications;
It is normal for the charger to overheat a little during use
Instructions
- You need to prepare an adapter and a lightning cable /a Type c cable;
- Connect the lightning cable to Magnetic Charging,
- Align the Apple watch back with Magnetic Charging, it will automatically absorb and start charging;
- When the watch is fully charged, it will automatically power off;
- Please tum off the power when you don’t need to charge
Notice:
- If the protective case of the watch is too thick, it may cause slow charging or no charging (please remove the protective case so that the watch can charge faster and more stably);
- If it fails to work, please check whether the power adapter is 5V/2Aor above. It is recommended to try an adapte「with 5V/2A or above for belier charging effect;
- If it cannot work, please contact us in time, we will solve your problem within 24 hours!!!
PRECAUTIONS FOR USE
If you’re not using the Apple Watch charging cable, disconnect it. The wrong
charging method can damage the charging cable. Always avoid moisture while
charging.
Liquid (sweat, drinking water , etc.) or foreign matter on the connector
part, Be careful not to allow (fine dust, dust, metalp1eces, etc.) to adhere.
Do not touch the power supply with wet hands.
Worn cable, broken insulation. or broken. Never use a device with a plug that
has a plug.
Charging your Apple Watch with the case removed And are recommended.
Places that get hot (near fire, near stove, etc.) Use or leave in a place
where flammable gas is generated Please do not
Places exposed to direct sunlight or extremely cold, Do not store ina place
with high humidity or dust, Apple Watch in a microwave oven,h1gh-pressure
container , etc
Do not drop or throw it under strong impact. Do not I disassemble or modify
Package Included:
1 xSmart Watch Magnetic Charging
1 x Instruction Manual
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 15cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>