MAYTAG W11681414A Commercial Washer Instruction Manual

INSTALLATION INSTRUCTIONS
CommerCial Washer

WASHER SAFETY

Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:

You can be killed or seriously injured if you don’t immediately follow instructions.
You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

• Read all instructions before using the washer.

• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode.

• Do not add gasoline, dry-cleaning solvents, or other flammable, or explosive substances to the wash water.
  These substances give off vapors that could ignite or explode.

• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine,  turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children.

• Before the washer is removed from service or discarded, remove the door or lid.

• Do not reach into the washer if the drum, tub or agitator is moving.

• Do not install or store the washer where it will be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in this manual or in published user-repair instructions that you understand and have the skills to carry out.
  See “Electrical Requirements” located in the installation instructions for grounding instructions.

• WARNING: Do not wash water-resistant or water-repellant type clothing. Failure to closely follow these instructions may result in an abnormal vibrating and out-of-balance condition that could result in physical injury, property damage, and/or appliance  damage.

SAVE THESE INSTRUCTIONS

FOR YOUR SAFETY
Do not store or use gasolin or other flamable vapors and liquids in the vicinity of this or any other applaince.

TOOLS & PARTS

Tools Needed:

Parts Supplied:

DIMENSIONS

Coin-operated models

LOCATION REQUIREMENTS

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room, or recessed area. See “Drain System.”
Companion appliance location requirements should also be considered.
IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Do not store or operate the washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Proper installation is your responsibility.

You will need:

• A water heater set to 120°F (49°C).
• A grounded electrical outlet located within 4 ft (1.2 m) of power cord on back of washer. See “Electrical Requirements.”
• Hot and cold water faucets located within 4 ft (1.2 m) of hot and cold water fill valves on washer, and water pressure of 20–100 psi (138–690 kPa). A pressure reduction valve should be used in the supply line where inlet pressure entering the building  exceeds 100 psi (690 kPa) to avoid damage to the washer mixing valve.
• Single washer installations require 12″ (300 mm) minimum risers to provide an air cushion and avoid noise and damage to valves.
• A level floor with maximum slope of 1″ (25 mm) under entire washer. Installing on carpet is not recommended.
• Floor must support washer’s total weight (with water and load) of 315 lbs (143 kgs).
• A floor drain under the bulkhead. Prefabricated bulkheads with electrical outlets, water inlet lines, and drain facilities should be used only where local codes permit.

Recessed Area or Closet Installation
This washer may be installed in a recessed area or closet.
The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing. If closet door is installed, the minimum air openings in top and bottom of door are required. Louvered doors  with air openings in top and bottom are acceptable.
Companion appliance spacing should be considered.

Minimum installation spacing

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.

It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.

1. Move washer to within 4 ft (1.2 m) of its final location; it must be in a fully upright position.
   NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is taped shut.
   

2. To avoid damaging floor, place cardboard supports from shipping carton on floor behind washer. Tip washer back and place on cardboard supports. Remove shipping base.
   Set washer upright.
   IMPORTANT: Removing shipping base is necessary for proper operation.
   NOTE: Keep shipping base in case you need to move washer later.
   

3. Remove tape from washer lid, open lid, and remove cardboard packing tray from tub. Be sure to remove all parts from tray.
   NOTE: Keep tray in case you need to move washer later.

LEVEL WASHER

IMPORTANT: Level washer properly to reduce excess noise and vibration.

Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.

1. Move the washer to its final location. Place a level on top edges of washer. Use side seam as a guide to check levelness of sides. Check levelness of front using lid, as shown. Rock washer back and forth to make sure all four feet make solid contact with floor.
   

2. Use a 9/16″ or 14 mm open-end or adjustable wrench to turn jam nuts clockwise on feet until they are about 1/2″ (13 mm) from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise to raise the washer.
   Recheck levelness of washer and repeat as needed.
   HELPFUL TIP : You may want to prop up front of washer about 4″ (102 mm) with a wood block or similar object that will support weight of washer.

3. When washer is level, use a 9/16″ or 14 mm open-end or adjustable wrench to turn jam nuts counterclockwise on leveling feet tightly against washer cabinet.

CONNECT DRAIN HOSE

Proper routing of the drain hose avoids damage to your floor due to water leakage.
Remove drain hose from the washer basket

1. Remove cap from the washer drain port on the back of the washer.

   ---

2. If clamp is not already in place on elbow end of drain hose, slide it over end as shown.
   

3. Squeeze clamp with pliers and slide elbow end of drain hose onto washer drain port and secure with clamp.
   IMPORTANT:
   ■ Drain hose is not to exceed 8″ (203 mm) into drain pipe; do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.
   ■ It is the responsibility of the installer to install and secure the drain hose into the provided plumbing/drain in a manner that will avoid the drain hose coming out of, or leaking from, the plumbing/drain.
   DRAIN SYSTEM

4. Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.
   4a. Floor drain system.
   For floor drain installations, you will need to remove the drain hose U-form on end of drain hose.
   Floor drain system requires a Siphon Break Kit (Part Number 285320). Minimum siphon break: 28″ (710 mm) from bottom of washer. Additional hoses may be needed.
   4b. Wall standpipe drain system.
   See requirements for floor standpipe drain system.
   4c. Floor standpipe drain system.
   Minimum diameter for a standpipe drain: 2″ (51 mm). Minimum carry-away capacity: 10 gallons (38 L) per minute. Top of standpipe must be at least 39″ (990 mm) high; install no higher than 96″ (2.44 m) from bottom of washer.
   4d. Laundry tub drain system.
   Minimum capacity: 20 gallons (76 L). The top of the laundry tub must be at least 39″ (990 mm) above floor.

CONNECT INLET HOSES

Insert new hose washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

Connect Inlet Hoses to Water Faucets

1. Attach hose to hot water faucet. Screw on coupling until it is seated on washer. Repeat process for cold water.

2. Use pliers to tighten the couplings an additional two-thirds turn. ****IMPORTANT: Do not overtighten or use tape or sealants on valve when attaching to faucets or washer. Damage can result.

3. Secure drain hose to inlet hose with zip strap.
   Clear Water Lines
   ■ Run water through both faucets and inlet hoses, into a laundry tub, drainpipe, or bucket to get rid of particles in the water lines that might clog the inlet valve screens.
   ■ Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

Connect Inlet Hoses to Washer

1. Attach cold water hose to cold water inlet valve marked with a blue ring. Screw coupling by hand until it is snug.

2. Attach hot water hose to hot water inlet valve marked with a red ring. Screw coupling by hand until it is snug.

3. Use pliers to tighten couplings an additional two-thirds turn.
   NOTE: Do not overtighten. Damage to the valve can result.

4. Turn on water faucets to check for leaks. A small amount of water may enter washer. It will drain later.
   NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates on the hoses for future reference.
   Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter. Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

• A 120 V, 60 Hz AC only, 15 A or 20 A, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
  It is recommended that a separate circuit breaker serving only this appliance be provided.

• This washer is equipped with a power supply cord having a 3 prong grounding plug.

• To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the  customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance — if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
For a permanently connected washer: This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment- grounding terminal or lead on the appliance.

COMPLETE INSTALLATION

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter. Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

• Check electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method.
• Check electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method.
• Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped.
• Check that you have all of your tools.
• Check that shipping materials were completely removed from washer.
• Dispose of/recycle all packaging materials.
• Check that the water faucets are on.
• Check for leaks around faucets and inlet hoses.
• Remove film from console and any tape remaining on washer.
• Plug into a grounded outlet or connect power.
• Check that circuit breaker is not tripped or fuse is not blown.
• Start the washer using the payment system if used and check that the washer completes the cycle without a fault or water leak.

INSTALLING COIN SLIDE AND COIN BOX

The coin slide mechanism, service door lock and key, and coin box lock and key are not included with some models, but can be obtained from the usual industry sources.
Remove the service door of the meter case by lifting it up at the back. Install the money-accepting device. (Refer to manufacturer’s instructions for proper installation.)
A ground connection is needed for the coin slide, which can be made by connecting the available harness (W10846503) to the coin slide.

Install a lock and cam on the meter case service door. Install the coin vault with lock and key in the meter case opening.

TYPICAL FULL LOAD SIZES

Load Type| Loading Suggestion| Load Type| Loading Suggestion
---|---|---|---
Mixed Load| 3  double sheets
4  pillowcases
6 pair shorts
8 T-shirts
2 shirts
2 blouses
8 handkerchiefs| Heavy Work Clothes| 3 pair pants
3 shirts
1 coverall
4 pair jeans
1 overall
Permanent Press| 2 double or
1 king size sheet 1 tablecloth
1 dress
1  blouse
2  slacks
3  shirts
2 pillowcases| Knits| 3  blouses

4  slacks

6 shirts

4 tops

4 dresses

WASHER MAINTENANCE

Operating Tips

Fire Hazard
Never place items in the washer that are dampened with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.

It is recommended that fiberglass items not be washed in coin-operated washers. If these items are washed in the washer, run the washer through a complete cycle to rinse any residue away that might be left in the washer.

Transporting Your Washer

• Shut off both water faucets. Disconnect and drain water inlet hoses.
• Disconnect drain from drain system and drain any remaining water into a pan or bucket. Disconnect drain hose from back of washer.
• Unplug power cord.
• Place inlet hoses and drain hose inside washer basket.
• Drape power cord over edge and into washer basket.
• Place packing tray from original shipping materials back inside washer and reuse shipping base to support the motor and tub. If you do not have original packaging, place heavy blankets or towels above basket, between the washer top and the tub ring. Close lid and place tape over lip and down the front of the washer. Keep lid taped until washer is moved to new location.

IF YOU NEED ASSISTANCE

Contact your authorized Commercial Laundry distributor. To  locate your authorized Commercial Laundry distributor, or for web inquiries, visit www.maytagcommerciallaundry.com.
If you cannot locate your distributor, the Commercial Laundry Support Center will answer any questions about operating or maintaining your washer not covered in the Installation Instructions.
Just dial 1-800-662-3587 — the call is toll free.
When you call, you will need the washer model number and serial number. Both numbers can be found on the serial-rating plate located on the washer.

ALTERNATE PARTS & ACCESSORIES

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number in the “If You Need Assistance” section.

utility sink, sump pump and connectors (available from local plumbing suppliers)
1″ (25 mm) standpipe| 2″ (51 mm) diameter to 1″ (25 mm) diameter Standpipe Adapter Part  Number 3363920 Connector Kit Part Number 285835
Lint clogged drain| Drain Protector Part Number 367031 Connector Kit Part Number 285835
Floor drain system| Siphon break, Part Number 285320 Connector Kit (x2)
Part Number  285835 Extension Drain Hose
Part Number 285863
Water faucets beyond reach of fill hoses| 2 longer water fill hoses: 6 ft (1.8 m) 90° bend hose
Part Number 76314, 10 ft (3.0 m)
Part Number 350008
| Inlet hoses are sold as a pair in kit W10575888
If You Have:| You Will Need:
Accessories
| Washer Drip Trays Part Number 8212526
| Fabric Softener Dispenser Kit Part Number 63594
Drain beyond reach of drain hose| 4 ft (1.2 m) Drain Hose Extension Part Number DRNEXT4

Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.

ELECTRONIC CONTROLS SET-UP INSTRUCTIONS

Basic Operation of Commercial Washer

• For additional information, see www.MaytagCommercialLaundry.com.

Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

IMPORTANT
Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.

• Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the washer.
  -OR
  Touch your finger repeatedly to a green ground connection point or unpainted metal in the washer.

• Before removing the part from its package, touch the anti-static bag to a green ground connection point or unpainted metal in the washer.

• Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.

• When repackaging failed electronic control assembly in anti-static bag, observe above instructions.

GENERAL INFORMATION
Blank Display
Check power to machine. Enter Service Mode and check for Fault Code.
‘0 Minutes’ showing in display
This indicates the previous cycle is complete or a machine reset was performed. Opening the lid will restore the display to the Vend Price or Available state.
Factory Default Settings
Washer is programmed at the factory as follows:
POWERWASH = Hot Water Main Wash – Deep Rinse – Heavy Soil Option Enabled- Extra Rinse Option Enabled – PD model pricing set to $2.50.

• MIXED = Warm Water Main Wash – Deep Rinse – No Options Enabled – PD model pricing set to $2.00.
• DELICATES = Cold Water Main Wash – Deep Rinse – No Options Enabled – PD model pricing set to $1.75.
• NORMAL ECO = Warm Water Main Wash – Progressive Spray Rinse – No Options Enabled – PD model pricing set to $1.75.

Refer to Cycle Settings in Program Menu to change default settings. All Cycles and Option Pricing set to 0 (Free Vend) on PR models.

Total calculated cycle price based on Base Cycle Cost + Cost of Options Selected (Extra Rinse, Soil Level, and Water Temperature). Default total cycle price dependent on Cycle Settings selected. PowerWash cycle price will not reduce from programmed settings  (Base Cycle Price + Cost of Options Selected per Cycle Settings) when end-user makes changes to selected cycle options (in example changes hot water to cold water). All other cycle prices are calculated based on final cycle selections made by the end-user.
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to the portion of the cycle that existed at time of the power failure.
To continue the cycle, press START.
Free Cycles
This is established by setting the cycle price to zero. When this happens, ‘SELECT CYCLE’ will appear and cycle price will show 0.00.
Debit Card Ready
This washer is debit card ‘cable’ ready. It will accept a variety of debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer setup. In models converted to a Generation 1 debit card system, debit pulses represent the equivalent of one coin (coin 1).
Display
After the washer has been installed and plugged in, the display will show ‘SYnC’ for a few seconds, then ‘0 MINUTES’. Once the washer has been plugged in and the washer door opened and closed, the display will show the price. In washers set for free cycles, the  display will flash ‘SELECT CYCLE’, and will display ‘PRICE 0.00’.

Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
The lower fabric setting keypads and the digital display are used to set up the controls. The display can contain four numbers and/or letters and a decimal point. These are used to indicate the set-up codes and related code values available for use in programming  the washer.
How to use the keypads to program the controls

1. The POWERWASH keypad is used to adjust the values associated with set-up codes. Pressing the keypad will increment the value.
   Rapid adjustment is possible by holding the keypad down.

2. The MIXED keypad will advance you through the set-up codes.
   Pressing the keypad will advance you to the next available set-up code. Holding the keypad down will automatically advance through the set-up codes at a rate of one (1) per second.

3. The DELICATES keypad is used to select or deselect options.

4. The TEMPERATURE keypad is used to decrease set-up code value.

Start Operating Set-Up

• PD Models: Insert access door key, turn, and lift to remove access door.
• PR models set for free vend: Refer to bottom of page 13 for entering operating setup.
• PR Models: Once the debit card reader is installed (according to the reader manufacturer’s instructions), the set-up mode can be entered by inserting a set-up card (supplied by the reader manufacturer) into the card slot. If a manual set-up card is not  available, manual set-up mode can be entered by removing connector AA1 on the circuit board.

IMPORTANT: The console must not be opened unless power is first removed from the washer. To access connector AA1:
→ Unplug washer or disconnect power.
→ Open console, disconnect plug on AA1, close console.
→ Plug in washer or reconnect power.
The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the options available, an owner can simply choose to uncrate a new commercial washer, hook it up, plug it in, and have a unit that operates.

Set-Up Codes
FOR PR MODELS: The set-up codes are the same as for the ‘PD’ models except where noted.
The set-up code is indicated by the one or two left-hand characters. The set- up code value is indicated by the two or three right-hand characters.

Coins or Debit pulses required to start the base cycle. See Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 – PR models default setting is 0.
6.07 NORMAL ECO| Amount to Start for NORMAL ECO Cycle*. Represents the number of Coins or Debit pulses required to start the base cycle. See Value of Coin

1. Adjustable from 0 to 200.
   PD models default setting is 7 – PR models default setting is 0.
   6.07 POWERWASH| Amount to Start for POWERWASH Cycle. Represents the number of Coins or Debit pulses required to start the cycle. See Value of Coin 1. Adjustable from 0 to 200.
   PD models default setting is 7 – PR models default setting is 0.
   6.08 MIXED| Amount to Start for MIXED Cycle. Represents the number of Coins or Debit pulses required to start the cycle. See Value of Coin
   1. Adjustable from 0 to 200.
   PD models default setting is 8 – PR models default setting is 0.
   ? Press the MIXED keypad once to advance to next code.
   P.dEF| Default Cycle Price displayed in Standby – Increase or decrease between MIXED, DELICATES, POWERWASH, NORMAL ECO by pressing the POWERWASH or TEMPERATURE keypad. Factory preset for MIXED.
   7.00| ADDITIONAL WASH TIME
   7.00| This is the number of minutes that can be added to a Wash Cycle.
   Choose from 00-05 minutes by pressing the POWERWASH keypad.
   ? Press the MIXED keypad once to advance to next code.
   8.00| ADDITIONAL RINSE TIME
   8.00| This is the number of minutes that can be added to a Rinse Cycle. Choose from 00-05 minutes by pressing the POWERWASH keypad.
   ? Press the MIXED keypad once to advance to next code.
   9.00| CYCLE COUNTER OPTION

This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.

9.00| Not Selected ‘OFF’.
9.0C| Selected ‘ON’ and not able to be deselected.
Press the DELICATES keypad 3 consecutive times to select ‘ON’. Once selected ‘ON’ it cannot be deselected.
? Press the MIXED keypad once to advance to next code.
1.00| MONEY COUNTER OPTION

This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.

1.00| Not Selected ‘OFF’.
1.0C| Selected ‘ON’.

Press the DELICATES keypad 3 consecutive times to select ‘ON’ and 3 consecutive times to remove (Not Selected ‘OFF’.) Counter resets by going from ‘OFF’ to ‘ON’.

1.C0| Selected ‘ON’ and not able to be deselected.

To select ‘ON’ and not able to be deselected, first select ‘ON’, then within 2 seconds press the DELICATES keypad twice, the POWERWASH keypad once, and exit the set-up mode.

? Press the MIXED keypad once to advance to next code.
2.00| SPECIAL PRICING OPTION

This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.

2.00| Not Selected ‘OFF’.
2.SP| Selected ‘ON’. Press the DELICATES keypad once for this selection.
If SPECIAL PRICING OPTION is selected, there is access to codes ‘3.’ through ‘9.’.
NOTE: An external battery needs to be added to keep the clock running during periods of power outages.
? Press the MIXED keypad once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
3.07 DELICATES| DELICATES Special Price Cycle Amount to Start. Represents the number of Coins or Debit pulses required to start the Special Price cycle. See Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 – PR models default setting is 0.
3.07 Normal ECO| NORMAL ECO Special Price Cycle Amount to Start. Represents the number of Coins or Debit pulses required to start the Special Price cycle. See Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 – PR models default setting is 0.
CODE| EXPLANATION
---|---
3.07
POWERWASH| POWERWASH Special Price Cycle Amount to Start. Represents the number of Coins or Debit pulses required to start the Special Price cycle. See Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 – PR models default setting is 0.
3.08
MIXED| MIXED Special Price Cycle Amount to Start. Represents the number of Coins or Debit pulses required to start the Special Price cycle. See Value of Coin 1. Adjustable from 0 to 200.
PD models default setting is 7 – PR models default setting is 0.
? Press the MIXED keypad once to advance to next code.
5.00| TIME-OF-DAY CLOCK, MINUTES
5.00| This is the TIME-OF-DAY CLOCK, minute setting; select between 0 and 59 minutes by pressing the POWERWASH or TEMPERATURE keypad.
? Press the MIXED keypad once to advance to next code.
6.00| TIME-OF-DAY CLOCK, HOURS
NOTE: Uses 24 hour clock.
6.00| This is the TIME-OF-DAY CLOCK, hour setting; select between 0 and 23 hours by pressing the POWERWASH or TEMPERATURE keypad.
? Press the MIXED keypad once to advance to next code.
7.00| SPECIAL PRICE START HOUR
NOTE: Uses 24 hour clock.
7.00| This is the start hour; select between 0 and 23 hours by pressing the POWERWASH or TEMPERATURE keypad.
? Press the MIXED keypad once to advance to next code.
8.00| SPECIAL PRICE STOP HOUR
NOTE: Uses 24 hour clock.
8.00| This is the stop hour; select between 0 and 23 hours by pressing the POWERWASH or TEMPERATURE keypad.
? Press the MIXED keypad once to advance to next code.
9.00| SPECIAL PRICE DAY
9.10| This represents the day of the week and whether special pricing is selected for that day. A number followed by ‘0’ indicates no selection that particular day (9.10). A number followed by an ‘S’ indicates selected for that day (9.1S).
Days of the week (1-7) can be chosen by pressing the POWERWASH keypad. Press the POWERWASH keypad once to select special pricing for each day chosen.
When exiting set-up code ‘9’, the display must show current day of week:
DISPLAY| DAY OF WEEK| CODE (selected)
10| Day 1 = Sunday| 1S
20| Day 2 = Monday| 2S
30| Day 3 = Tuesday| 3S
40| Day 4 = Wednesday| 4S
50| Day 5 = Thursday| 5S
60| Day 6 = Friday| 6S
70| Day 7 = Saturday| 7S
? Press the MIXED keypad once to advance to next code.
A.00| VAULT VIEWING OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
A.00| Not Selected ‘OFF’.
A.SC| Selected ‘ON’. Press the DELICATES keypad once for this selection. When selected, the money and/or cycle counts will be viewable (depending on what is selected) when the coin box is removed.
CODE| EXPLANATION
---|---
? Press the MIXED keypad once to advance to next code.
b.05| VALUE OF COIN 1
b.05| This represents the value of coin 1 in number of $0.05 increments of the larger coin value. 5 x $0.05 = $0.25.
By pressing the POWERWASH or TEMPERATURE Keypad, there is the option of 1-199 for the quantity of $0.05 increments.
? Press the MIXED keypad once to advance to next code.
C.20| VALUE OF COIN 2
C.20| This represents the value of coin 2 in number of $0.05 increments of the larger coin value. 20 x $0.05 = $1.00.
PR MODELS ONLY: Factory preset for $0.25
By pressing the POWERWASH or TEMPERATURE Keypad, there is the option of 1-199 for the quantity of $0.05 increments.
? Press the MIXED keypad once to advance to next code.
d.00| COIN SLIDE OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
d.00| Not Selected ‘OFF’.
d.CS| Selected ‘ON’. Press the DELICATES Keypad 3 consecutive times for this selection.
When coin slide mode is selected, set ‘b.’ equal to value of slide in $0.05 increments. Set step 6 (regular cycle price) and step 3 (special cycle price) to number of slide operations. If the installer sets up ‘CS’ on a coin drop model, it will not register coins.
? Press the MIXED keypad once to advance to next code.
E.00| ADD COINS OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’. This option causes the customer display to show the number of coins (coin 1) to enter, rather than the dollars-and-cents amount.
E.00| Not Selected ‘OFF’.
E.AC| Selected ‘ON’. Press the DELICATES keypad 3 consecutive times for this selection.
? Press the MIXED keypad once to advance to next code.
H.00 COLD| COLD Temperature Upgrade – Represents the amount of Coins or Debit pulses required to purchase the Cold Temperature Upgrade. Adjustable between 0 and 40. Factory default is set for 0.
H.00 COOL| COOL Temperature Upgrade – Represents the amount of Coins or Debit pulses required to purchase the Cool Temperature Upgrade. Adjustable between 0 and 40. Factory default is set for 0.
H.00 WARM| WARM Temperature Upgrade – Represents the amount of Coins or Debit pulses required to purchase the Warm Temperature Upgrade. Adjustable between 0 and 40. Factory default is set for 0.
H.01 HOT| HOT Temperature Upgrade – Represents the amount of Coins or Debit pulses required to purchase the Hot Temperature Upgrade. Adjustable between 0 and 40. Factory default is set for 1 on PD models and set for 0 on PR models.
H.01 HEAVY| HEAVY SOIL Upgrade* – Represents the amount of Coins or Debit pulses required to purchase the Heavy Soil Upgrade.

Adjustable between 0 and 40. Factory default is set for 1 on PD models and set for 0 on PR models.

H.01 EXTRA RINSE| EXTRA RINSE Upgrade* – Represents the amount of Coins or Debit pulses required to purchase the Extra Rinse Upgrade. Adjustable between 0 and 40. Factory default is set for 1 on PD models and set for 0 on PR models.
? Press the MIXED keypad once to advance to next code.
CODE| EXPLANATION
---|---
J.Cd| COIN/DEBIT OPTION
J.Cd| Both coin & debit selected.
J.C_| Coins selected, debit disabled. Press the DELICATES keypad 3 times for this selection.
J._d| Debit Card selected, coins disabled. Press the DELICATES keypad 3 times for this selection.
J.Ed| Enhanced Debit is self-selected when a Generation 2 card reader is installed in the washer. The Ed option cannot be manually selected or deselected.
? Press the MIXED keypad once to advance to next code.
L.00| PRICE SUPPRESSION OPTION

This option causes the customer display to show ‘ADD’ or ‘AVAILABLE’ rather than the amount of money to add. (Used mainly in debit installations.)

L.00| Not Selected ‘OFF’.
L.PS| Selected ‘ON’. Press the DELICATES keypad once for this selection.
? Press the MIXED keypad once to advance to next code.
n. CE| CLEAR ESCROW OPTION

When selected, money held in escrow for 30 minutes without further escrow or cycle activity will be cleared.

n. CE| Selected ‘ON’.
n. 00| Not selected ‘OFF’. Press the DELICATES keypad once to deselect this selection.
? Press the MIXED keypad once to advance to next code.
A3.03| MIXED Cycle Settings. Allows the owner to select the cycle default options of Water Temperature, Soil Level, and Extra Rinse.

See Table 1 for specific settings. MIXED is set to 03 from the factory.

A4.01| DELICATES Cycle Settings. Allows the owner to select the cycle default options of Water Temperature, Soil Level, and Extra Rinse.

See Table 1 for specific settings. Delicates is set to 01 from the factory.

A5.1C| POWERWASH Cycle Settings. Allows the owner to select the cycle default options of Water Temperature, Soil Level, and Extra Rinse.

See Table 1 for specific settings. Powerwash is set to 1C from the factory.

A6.03| NORMAL ECO Cycle Settings. Allows the owner to select the cycle default options of Water Temperature, Soil Level, and Extra Rinse.

See Table 1 for specific settings. Normal Eco is set to 03 from the factory.

? Press the MIXED keypad once to advance to next code.

If cycle counter (9.0C) is selected, the following is true:

If money counter (1.0C or 1.C0) is selected, the following is true:

END OF SET-UP PROCEDURES

EXIT FROM SET-UP MODE

• PD Models: Reinstall access door.
• PR Models:
  → Unplug washer or disconnect power.
  →  Open console, reinsert plug into AA1, close console.
  →  Plug in washer or reconnect power.

If preferred, just wait through 2 minutes of inactivity. All settings will be saved and the display will revert to Select Cycle screen.

Table 1

A3, A4, A5, A6| Extra Rinse| Soil Level (Heavy-On, Normal-Off)| Water Temp| A3, A4, A5, A6| Extra Rinse| Soil Level (Heavy-On, Normal-Off)| Water Temp
---|---|---|---|---|---|---|---
00| Off| Off| Tap Cold| 10| On| Off| Tap Cold
01| Off| Off| Cold| 11| On| Off| Cold
02| Off| Off| Cool| 12| On| Off| Cool
03| Off| Off| Warm| 13| On| Off| Warm
04| Off| Off| Hot| 14| On| Off| Hot
08| Off| On| Tap Cold| 18| On| On| Tap Cold
09| Off| On| Cold| 19| On| On| Cold
A| Off| On| Cool| 1A| On| On| Cool
B| Off| On| Warm| 1B| On| On| Warm
C| Off| On| Hot| 1C| On| On| Hot

Technician Service Access Code
This method is only available on PR washers set to free vend (6 00).
To enter service mode:
Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES keypads within 10 seconds.
To exit service mode:
From service code 8.xx, press the POWERWASH keypad for 4 seconds.
or
Wait 2 minutes without touching any keypads (without diagnostic modes running).
or
Power down the washer, then reapply power.

NOTE: If a service cycle is in progress upon exiting service mode, the cycle will complete normally with cycle status information displayed. The display will resume normal customer operation mode when the cycle ends.

W11681414A
®/TM ©2023 Maytag. All rights reserved. Used under license in Canada.

References

• Maytag Commercial Laundry | Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>