EWU B0BHLBDGMH 12 Pack LED Recessed Lighting 4 Inch 5CCT Canless Lights User Guide

EWU B0BHLBDGMH 12 Pack LED Recessed Lighting 4 Inch 5CCT Canless Lights

Product Information

The product is a recessed light with various high-standard certifications such as ETL and Energy Star. It is an IC-rated canless LED recessed light that comes with UL connectors for convenience and security. The product is available in different models and sizes, and it is dimmable. It has a beam angle, input voltage, operating temperature, and work humidity specifications.

Product Usage Instructions

1. Power Off: Before installing the light, make sure to turn off the power.
2. Location Marker: Mark the positions on the ceiling where each light will be installed using a pencil. Draw circles that fit into the light.
3. Cut Hole: Punch a hole in the ceiling at the marked circle position.
4. Threading In: Open the junction box and remove the knock-out on the side. Run the wire from the power source through the hole. Purchase connectors from a local hardware store.
5. Connect Line: Use the connector to tuck the wires together according to their colors. Close the cover of the junction box. Flip the switch on the side of the junction box to select the desired lighting effect.
6. Connect Light and Junction Box: Tighten the junction box to the light panel.
7. Install J-Box: Put the junction box into the ceiling hole and push up the spring clips to secure it.
8. Install the Light: Push the light into the ceiling until it is securely in place. Power on.

Installation

1. 【Power Off】Please turn off the power when installing
2. 【Location Marker】Mark where each light will be installed on the ceiling, and use a pencil to draw circles that just fit into the light
3. 【Cut Hole】In the place where the circle is drawn, punch the corresponding hole
4. 【Threading In】Open the junction box and remove knock-out on the side run wire from the power source through the hole and you can buy the connectors from local hardware store
5. 【Connect Line】Use the connector to tuck the wires according to the color. then close the cover .flip the switch on the side of the junction box to locate the setting that you like
6. 【Connect light and junction box 】Connect (Tighten to the right) the junction box to the light panel
7. 【Install J-Box】Put the box in the ceiling hole. push up the spring clips
8. 【Install the light】Push the light in to the ceiling and power on

NOTICE
Installations should be done by a licensed electrician.

1. Please be sure the power is shut off before process；
2. Risk of fire and electrical shock；
3. Don’t change or remove any wire or any components from the fixture ;

SAFETY INSTRUCTION

EWU recessed light has various high standard certifications such as ETL and Energy Star This canless LED recessed light is IC rated, with more  convenient and secure UL connectors but in order to ensure safety,please before operation read all warnings and instructions included with and on the fixture labels

RISK OF ELECTRIC SHOCK:

• All electrical connection must be in accordance with local and National Electric Code (N.E.C.) standards.
• Consult a qualifised electrician if you are unfamiliar with proper electrical wiring connections.
• Turn off the switch and circuit breaker before installing this LED light.
• Do not alter, re-locarte or remove wiring.
• Double-check all connections to be sure they are tight and correct.
• Verify that supply voltage is correct by comparing it with the luminaire abel information.

RISK OF FIRE:

• Keep combustibles and other materials that may burn away from lights
• The maximum ambient temperature is 104°F.Do not operate fixture at temperatures higher than it

RISK OF INJURY:

• The knockouts may be sharo.Wear gloves and safety glasses at all time when removing luminaire, installing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on
• Wear rubber-soled shoes and work on a sturdy wooden ladder

RISK OF BURN:

• Do not touch enclosure or light source. It is normal of the luminaire surface heating up during work. Allow lights to cool before handling

RISK OF PRODUCT DAMAGE:

• Electrostatic Discharge(ESD): ESD candamage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
• Do not touch individualelectrical components as this can cause ESD shorten lamp life, or alter performance.
• Do not mi our product with other products (eg. 4″ and 6″) Mxing junction box of different power will lead to the destruction of the prod- uct.
• Do not let the prodGct directly contact with waterOur productis damp-rated but it is not water-proof.
• Do not make or alter any open holes in an enclosure of wiring or elec- trical components. Never connect components under load.

Product Specifications

Dimmer Switch

Please use a compatible led dimmer switch for the best job.

NOTICE
If you have smart home dimming products, such as Savant, Crestron, Control4, etc., and want to know the compatibility of this product, please contact our after-sales department for the latest information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>