GAGGENAU VR414115 Vario Electric Grill 400 series Owner’s Manual
- June 13, 2024
- Gaggenau
Table of Contents
GAGGENAU VR414115 Vario Electric Grill 400 series
Product Information
The VR414115 Vario electric grill is part of the 400 series and is made of stainless steel. It has a width of 38 cm.
The grill comes with the following included accessories:
- 1 x cast pan (half-size)
- 2 x cast iron grill
- 1 x lava stones
- 1 x cleaning brush
There is also an optional accessory available, the LV030000.
For installation purposes, there are several accessories available:
- VA420004 Connection strip for combination with other Vario appliances of the 400 series for flush mounting
- VA420010 Connection strip for combination with other Vario appliances of the 400 series for surface mounting
- VA440010 Stainless steel appliance cover with a mounting strip
The total connected load for the grill is 3.0 KW. It comes with a connecting cable of 1.5 m in length without a plug.
Product Usage Instructions
- Ensure that the grill is placed on a stable and heat-resistant surface.
- Connect the grill to a power source using the provided connecting cable.
- Before using the grill for the first time, clean the grill and accessories with the provided cleaning brush.
- To use the cast pan, place it on the grill surface and preheat it to the desired temperature.
- For grilling, place the cast iron grills on the grill surface and preheat them as well.
- If desired, add lava stones to the grill for enhanced flavor and heat distribution.
- Turn on the grill and adjust the temperature according to your preference.
- Place the food on the grill surface and cook it to your desired doneness, flipping as needed.
- After use, allow the grill to cool down completely before cleaning.
- Clean the grill and accessories thoroughly using the provided cleaning brush.
- Store the grill and accessories in a clean and dry place.
- Note: Refer to the user manual for detailed cleaning and maintenance instructions.
- VR414115
- Vario electric grill 400 series
- Stainless steel
- Width 38 cm
Color Variants
- VR414115
- Stainless steel
- Width 38 cm
Included accessories
- 1 x cast pan.
- half size.
- 2 x cast iron grill.
- 1 x lava stones.
- 1 x cleaning brush.
Optional accessories
- LV030000
Installation Accessories
VA420004
- Connection strip for combination with other Vario appliances of the 400 series for flush mounting
VA420010
- Connection strip for combination with other Vario appliances of the 400 series for surface mounting
VA440010
- Stainless steel appliance cover with mounting strip
- Two zones can be operated together or separately
- Cast pan, half size, for simultaneous frying and grilling on two separate surfaces
- Open cast grill, lava stones
- Solid stainless steel knob, also selectable with black robust finishing, for precise control and personalisation
- Precision crafting of 3 mm stainless steel
- For surface mounting with a visible edge or for flush mounting
- Can be combined perfectly with other Vario appliances of the 400 series
Handling
- Control knobs with illuminated ring, cooking zone and output level markings.
- Electronic power control in 12 output levels.
Features
- Cooktop, lava stone trough and grease collecting insert from stainless steel.
- Two zones, each 1500 W, can be operated together as a complete surface or each half separately.
- Two-part cast grill.
Safety
- Safety shut-off.
- Pre-heat and residual heat indicator.
Planning notes
- Depending on the type of installation (surface-mounted or flush-mounted, with or without an appliance cover), the specific location of the cut-out and the knob positions may vary.
- If installing with the appliance cover VA 440 take into account the additional space required for the depth.
- If combining several Vario appliances of the 400 series, a connection strip VA 420 must be placed between the appliances. Depending on the type of installation, the corresponding connection strip must be provided.
- The bearing capacity and stability, in the case of thin worktops in particular, must be supported using suitable substructures. Take into account the appliance weight and additional loads. Additional instructions for flush mounting:
- Installation is possible in worktops made of stone, synthetics or solid wood. Heat resistance and watertight sealing of the cut edges must be observed. Concerning other materials please consult the worktop manufacturer.
- The groove must be continuous and even, so that uniform placing of the appliance on the gasket is ensured. Do not use discontinuous lining.
- The joint width may vary due to size tolerances of the combinations and of the worktop cut-out.
- If installing several appliances in individual cut-outs allow for a division bar of minimum 50 mm between the individual cut-outs.
- A minimum lateral clearance of at least 100 mm from adjacent heat-sensitive furniture or from the wall must be observed.
- Appliance can be snapped into the worktop from above.
- Appliance weight: approx. 27.
Characteristics
-
Frequency 50-60
-
Product name/family Vario/Domino barbecue grill
-
Built-in / Free-standing Built-in
-
Energy input
-
Electric
-
Type of control Electronic
-
Grill grating material Cast iron
-
Min. required niche size for installation (HxWxD)
- 118 x 360 x 492
-
Width of the appliance 380
-
Dimensions (HxWxD) 118 x 380 x 520
Dimensions of the packed product (HxWxD)- 400 x 460 x 600
-
Net weight 26.9
Gross weight 29.7 -
Residual heat indicator
-
separate
-
Location of the control panel
-
Hob front
-
Basic surface material
-
Cast iron
-
Color of surface
-
Stainless steel, Stainless steel
-
Color of frame
-
Stainless steel
-
Length electrical supply cord 150
-
Connection Rating 3000
-
Gas connection rating
-
Fuse protection 16
Voltage
- 220-240
Included accessories
- 1 x cast pan, half size, 2 x cast iron grill,
- 1 x lava stones, 1 x cleaning brush
- Consumption and connection features 2023-01-15 Page 1
Connection
- Total connected load 3.0 KW.
- Connecting cable 1.5 m without plug.
VR414115
- Vario Electric Grill 400 series
- Stainless steel
- Width 38 cm 2023-01-15 Page 2
INSTALLATION INSTRUCTION
- A: When installing with appliance cover, take the deeper cut-out into
- B: 19 duration area or the carte lap net, on the rear side)
- C: 3.5-05
- 6.5°°*in combinations with frameless induction hob measurements in mm
Installation with appliance cover, flush mounting
Installation with appliance cover, surface mounting
Cross-section
- A: 3.5-05
- 6.5*05in combination with frameless induction hobs
- B : Fill with silicone
- When installing with an appliance cover, pay attention to the deeper cut-out and the front and rear groove width.
- measurements in mm
View from above
- A: When installing with appliance cover, take the deeper cut-out into consideration (observe separate planning notes)
- measurements in mm
Longitudinal section
- A: 3.5-0.5 6.5*05in combinations with frameless induction hobs
- B: Fill with silicone
- measurements in mm
Installation with appliance cover, flush mounting
- A: 3.505
- measurements in mm
Installation with appliance cover, surface mounting
Installation of the control knob; surface mounting
measurements in mm
Installation of the control knob; flush installation
measurements in mm
- A: When installing with appliance cover, take the deeper cut-out into consideration (observe separate planning notes)
- B: 130 mm in the area of the cable clamp (left, on the rear side)
- measurements in mm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>