CYP CH-2603TX HDMI HDBaseT USB to HDMI Receiver User Manual

CYP CH-2603TX HDMI HDBaseT USB to HDMI Receiver

Product Information

The C H-2603RX is a versatile receiver that allows you to connect HDMI, HDBaseT, and USB devices to your HDMI display. With multiple input options and convenient controls, this receiver provides a seamless and efficient user experience.

Disclaimer Please note that all product or service names mentioned in this document are trademarks of the companies with which they are associated.

Safety Precautions Prior to unpacking, installing, or operating this equipment, it is important to read and understand all instructions. Also, ensure that the power supply is properly connected. Please keep the following in mind during the unpacking and installation process.

Version History

• REV. DATE RDV1 2019/04/29
  Summary of Change: Preliminary release

Product Usage Instructions

Introduction The C H-2603RX is a receiver that allows you to connect HDMI, HDBaseT, and USB devices to your HDMI display. It provides seamless transmission of audio and video signals.

Applications The C H-2603RX is suitable for various applications, including home entertainment systems, conference rooms, and digital signage setups.

Package Contents The package includes the following items:

• C H-2603RX HDMI/HDBaseT/USB to HDMI Receiver
• Power Supply
• User Manual

System Requirements To use the C H-2603RX, ensure that you have the following:

• An HDMI display
• HDMI, HDBaseT, and USB devices
• Power supply

Features

• Supports HDMI, HDBaseT, and USB connections
• Allows extension of USB functionality to connected devices
• Convenient front and rear panel controls for easy operation
• LED indicators for power, link status, and selected input sources
• RS-232 port for serial control of the unit
• Web GUI control for remote management

Operation Controls and FunctionsFront Panel The front panel of the C H-2603RX includes the following controls and indicators:

• POWER LED: Illuminates to indicate that the unit is powered on and receiving power
• LINK LED: Illuminates solidly when a live connection with a compatible Transmitter is active
• LOCAL RS-232 Port: Connect directly to a PC, laptop, or other serial control device using a 3.5mm adapter cable to send RS-232 commands to control the unit
• OUT1 Button & LEDs: Toggle between available inputs for HDMI output 1. The OUT 1 LED illuminates to indicate the currently selected source
• OUT2 Button & LEDs: Toggle between available inputs for HDMI output 2. The OUT 2 LED illuminates to indicate the currently selected source
• USB Device Ports (Type A): Connect standard USB devices such as a mouse, keyboard, or flash drive to extend their functionality to the currently active USB Host Port
• USB SELECT Button & LED: Toggle between using the USB Host Port on the Receiver or the USB Host Ports on the connected Transmitter. The LED illuminates when the USB Host Port on the Receiver is active. If the LED is off, then none of the USB Host Ports on the connected Transmitter is active. Note that changing the USB host will briefly disconnect the HDBaseT connection while it reconfigures.

DISCLAIMERS

• The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
• Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
• Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

• No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology.
• © Copyright 2018 by Cypress Technology.
• All Rights Reserved.

TRADEMARK ACKNOWLEDGMENTS

• All products or service names mentioned in this document are trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

• Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in use to avoid wasting electricity.

VERSION HISTORY

INTRODUCTION

• This HDBaseT 2.0 Receiver is designed for use in environments needing a wide range of flexibility when it comes to inputs, outputs, and control. With a 2 by 2 matrix arrangement of HDBaseT & HDMI inputs and dual HDMI outputs this Receiver can handle a variety of source routing scenarios. The HDMI input and outputs support resolutions
  up to a maximum of 4K@60Hz (4:4:4, 8-bit) while the HDBaseT input supports resolutions up to a maximum of 4K@60Hz (YUV 4:2:0, 8-bit). A balanced analog stereo audio breakout is also provided (LPCM 2.0 sources only) allowing for professional local powered speakers to be easily added to the system. The HDBaseT input not only supports video and audio but also bi-directional Ethernet, RS-232, USB, and IR.

• When paired with this unit’s standard Transmitter, up to 3 switchable USB 2.0 host (Type B) connections are available (2 on the Transmitter, 1 on the Receiver) which connect to 6 USB 2.0 (Type A) device ports (3 on the Transmitter, 3 on the Receiver) for a multi-source, bi-directional, and highly flexible KVM configuration (Note: Only 1 USB host may be active at a time).

• This Receiver (PSE) can provide PoH (Power over HDBaseT) power to the connected HDBaseT Transmitter (PD) (compatible Transmitters only), allowing for greater flexibility within different installation scenarios. This unit is controllable via front-panel controls, WebGUI, Telnet, and RS-232.

APPLICATIONS

• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control

PACKAGE CONTENTS

• 1×HDMI/HDBaseT/USB to HDMI Receiver
• 1×24V/3.75A DC Power Adapter
• 1×3.5mm to IR Blaster Cable
• 1×3.5mm to IR Extender Cable
• 1×Shockproof Feet (Set of 4)
• 1×Operation Manual
• 1x power cord
• 1×3-pin terminal block
• 1×5-pin terminal block

SYSTEM REQUIREMENTS

• HDMI source equipment such as a media player, video game console, or set-top box.
• A compatible HDBaseT transmitter with PoH (PD) support is recommended.
• HDMI receiving equipment such as HDTVs, monitors or audio amplifiers.
• The use of Premium High Speed HDMI cables, and industry standard Cat.6, Cat.6a or Cat.7, is highly recommended.

FEATURES

• HDMI input and output with 3D & 4K video support (18Gbps)
• HDCP 1.x & 2.2 compliant
• HDBaseT 2.0 compatible
• Selectable HDMI and HDBaseT inputs
• HDMI input supports resolutions up to 4K@60Hz (4:4:4, 8-bit)
• HDBaseT input supports resolutions up to 4K@60Hz (YUV 4:2:0, 8-bit)
• HDMI outputs support resolutions up to 4K@60Hz (4:4:4, 8-bit)
• 2×2 matrix switching (both HDMI outputs are independent)
• Supported HDBaseT features: HD video and audio, 100BaseT Ethernet, PoH, and control (bi-directional IR/RS-232/USB pass-through)
• Supports pass-through of 8 channel LPCM, Bitstream & HD Bitstream audio formats
• Balanced analog stereo audio breakout
• Flexible USB host selection using front panel buttons
• Multiple USB hosts may be connected at once (up to 3 total, between the Tx and a compatible Rx unit) with a single selected host active at a time
• Supports providing PoH power from Receiver (PSE) to Transmitter (PD)(compatible Transmitters only)
• Controllable via front panel buttons, WebGUI, Telnet, and RS-232

OPERATION CONTROLS AND FUNCTIONS

Front Panel

1. POWER LED: This LED will illuminate to indicate the unit is on and receiving power.
2. LINK LED: This LED will illuminate solidly when a live connection with a compatible Transmitter is active.
3. LOCAL RS-232 Port: Connect directly to a PC, laptop, or other serial control device with a 3.5mm adapter cable to send RS-232 commands to control the unit.
4. OUT 1 Button & LEDs: Press this button to toggle between theavailable inputs for HDMI output 1. The OUT 1 LED will illuminate to indicate which source is currently selected. OUT 2 Button & LEDs: Press this button to toggle between the available inputs for HDMI output 2. The OUT 2 LED will illuminate to indicate which source is currently selected.
5. USB Device Ports (Type A): Connect directly to standard USB devices such as a mouse, keyboard or flash drive to extend their USB functionality to the currently active USB Host Port.
6. USB SELECT Button & LED: Press this button to toggle between using the USB Host Port on the Receiver or the USB Host Ports on the connected Transmitter. The LED will illuminate when the USB Host Port on the Receiver is active. If the LED is off, then one of the USB Host Ports on the connected Transmitter is active.

Note: Changing the USB host will force the HDBaseT connection to briefly disconnect while it reconfigures. The connected host (PC, Laptop, etc.) may also take a moment to detect all available devices.

Rear Panel

1. USB Host Port (Type B): Connect directly to a standard USB host such as a PC or laptop to extend their USB functionality to all currently connected USB devices.
   Note: Only one USB Host Port may be active at a time.

2. IR IN Port: Connect to the provided IR Extender to receive IR control signals and extend them to devices connected to the other end of the HDBaseT connection.
   Ensure that the remote being used is within direct line-of-sight of the IR Extender. IR OUT Port: Connect to the provided IR Blaster to transmit IR signals from the other end of the HDBaseT connection to devices within direct line-of-sight of the IR Blaster.

3. CAT5e/6/7 IN Port: Connect to a compatible HDBaseT Transmitter with a single Cat.5e/6/7 cable for reception of all data signals. PoH will also be supplied to a connected compatible PD Transmitter.

4. DMI IN Port: Connect to HDMI source equipment such as a media player, game console, or set-top box.

5. ANALOG OUT Terminal Block: Connect to powered speakers or an amplifier using a 5-pin terminal block for balanced stereo analog audio output.

6. HDMI OUT 1 Port: Connect to an HDMI TV, monitor, or amplifier for digital video and audio output.

7. HDMI OUT 2 Port: Connect to an HDMI TV, monitor, or amplifier for digital video and audio output.

8. BYPASS RS-232 Terminal Block: Connect to a PC, laptop, or other serial control device with a 3-pin adapter cable for the extension of RS-232 signals to the Transmitter.

9. LAN Port: Connect directly, or through a network switch, to your PC/laptop to control the unit via Telnet/WebGUI and to extend the network across the HDBaseT connection.

10. DC 24V Port: Plug the 24V DC power adapter into this port and connect it to an AC wall outlet for power.

Cable Pinouts

RS-232 Pinout and Defaults

Serial Port Default Settings

Baud Rate| 19200
Data Bits| 8
Parity Bits| None
Stop Bits| 1
Flow Control| None

WebGUI Control

Device Discovery

• Please obtain the “Device Discovery” software from your authorized dealer and save it in a directory where you can easily find it.
• Connect the unit and your PC/Laptop to the same active network and execute the “Device Discovery” software. Click on “Find Devices on Network” and a list of devices connected to the local network will show up indicating their current IP address.
• Note: The unit’s default IP address is 192.168.1.50.
• By clicking on one of the listed devices you will be presented with the network details of that particular device.

1. IP Mode: If you choose, you can alter the static IP network settings for the device, or switch the unit into DHCP mode to automatically obtain proper network settings from a local DHCP server. To switch to DHCP mode, please select DHCP from the IP mode drop-down, then click “Save” followed by “Reboot”.
2. WebGUI Hotkey: Once you are satisfied with the network settings, you may use them to connect via Telnet or WebGUI. The network information window provides a convenient link to launch the WebGUI directly.

WebGUI Overview

• After connecting to the WebGUI’s address in a web browser, the login screen will appear. Please enter the appropriate user name and password then click “Submit” to log in.
• Note: The default user name and password is “admin”.
• On the left side of the browser you will see the following menu tabs where all primary functions of the unit are controllable via the built in WebGUI. The individual functions will be introduced in the following sections.
• Clicking the red “Logout” tab will automatically log the currently connected user out of the WebGUI and return to login page. Clicking on the “Transmitter Webpage” button will open a new webpage showing the WebGUI for the connected Transmitter.

Video Select Tab

• This tab provides A/V routing control, auto switch controls, and I/O renaming options.
• To assign a new A/V route, please click the button of the Output you wish to route a source to on the left and then click on the button of the preferred Input port on the right. Selecting both Outputs simultaneously is possible.
• As you select each button they will become yellow. The new route will become active immediately and the routing information displayed on the buttons will change accordingly.

Video Select:

• Output: Buttons for selecting the Output (A or B) to route A/ V Inputs to. Details about the Output names and currently selected Input are also displayed here. Clicking on the “edit” icon ( ) opens up the Edit Output window which allows for changing the Output’s name.
• Input: Buttons for selecting the Input (1 through 2) to route to the selected Output. The current Input names are also displayed here. Clicking on the “edit” icon ( ) opens up the Edit Input window which allows for changing the Input’s name.
• Auto Switch: Auto switching may be enabled or disabled individually for each Output. Click on the On/Off slider to toggle the behavior of the selected Output.
• This unit can store up to two routing presets. Presets can be utilized to store multiple different routing states in advance for rapid, hassle-free, recall.
• Preset Set: Once you have the routing set the way you like, you can click the “Preset Set” icon ( ) in the upper right corner of the tab to open the Preset Set window. Click on the preferred Preset button when you are ready to commit the preset to memory. You may also rename the preset at this stage by selecting the “edit” icon ( ) .
• Preset Recall: When you wish to load a previously stored preset, please click the “Preset Recall” icon ( ) and you will be presented with a choice of the 2 available presets. The preset will load immediately upon selecting the button..

EDID Tab

• This tab provides the option of six standard EDIDs, two sink sourced
• EDIDs and two customer uploaded User EDIDs that can be assigned to either or both of the input ports.

Customer EDID Settings

• Save Name: To modify the name of a User EDID, simply type the new name in the space provided and then click on the “Save Name” button to confirm the change.
• Upload: To upload a User EDID, press the “Upload” button next to the User EDID slot you wish to upload into. An EDID Upload window will appear, allowing you to locate and upload the preferred EDID file (*.bin format) from a local PC. Once the correct file has been selected, please click the “Upload” button in the window, and the file will be transferred to the unit.
• Download: To save an existing User EDID to your local PC, press the “Download” button next to the User EDID slot you wish to save. Depending on your browser settings you will either be asked where to save the downloaded file, or the file will be transferred to the default download location on your PC.
• Sink EDID Download: To save the EDID from a connected display to your local PC, select the sink from the dropdown list then press the “Download” button. Depending on your browser settings you will either be asked where to save the downloaded file, or the file will be transferred to the default download location on your PC.
• Set EDID Input Content/EDID Source : The Set EDID Input Content section allows for the assignment of a specific EDID to either Input port. Click on one or more input buttons on the left and then select the new EDID source to use from the choices on the right. The buttons will change color as you select them and the EDID change will occur immediately across all selected Inputs.
• Note: In most cases, assigning a new EDID to an input will cause the affected input to briefly blink out while the source adapts to the new information.

This unit provides the following 6 default EDIDs:

Unit’s Default EDIDs

FHD/2CH| 1920×1080p@60Hz (148MHz) &

8-bit color

| LPCM 2.0
FHD/MCH| 1920×1080p@60Hz (148MHz) &

8-bit color

| LPCM 7.1 &

Bitstream

UHD/2CH| 3840×2160p@30Hz (297MHz) &

Deep Color (8/10/12-bit)

| LPCM 2.0
UHD/MCH| 3840×2160p@30Hz (297MHz) &

Deep Color (8/10/12-bit)

| LPCM 7.1 &

Bitstream

UHD+/2CH| 3840×2160p@60Hz (594MHz) &

Deep Color (8/10/12-bit)

| LPCM 2.0
UHD+/MCH| 3840×2160p@60Hz (594MHz) &

Deep Color (8/10/12-bit)

| LPCM 7.1 &

Bitstream

Note: In some rare cases it is possible for custom or external EDIDs to cause compatibility issues with certain sources. If this happens, it is recommended to switch to one of the 6 default EDIDs for maximum compatibility.
HDCP Tab
This tab provides the option of three HDCP operational modes that can be assigned to any of the input ports.

1. Set HDCP Input Mode/HDCP Mode: The HDCP Input Mode section allows for the assignment of a specific HDCP behavior to any Input port. Click on one or more input buttons on the left and then select the new HDCP mode to use from the choices on the right. The buttons will change color as you select them and the change in HDCP behavior will occur immediately across all selected Inputs. “Reference to Source” will make the input operate using the HDCP version required by the connected source.
   • Reference to Display” will limit the input to only accept the HDCP version supported by the connected display. Selecting “Disable” will completely disable HDCP support on that input.

USB Tab
This tab provides a way to select which USB Host Port (USB Type B) is currently active.
Note: Changing the USB host will force the HDBaseT connection to briefly disconnect while it reconfigures. The connected host (PC, Laptop, etc.) may also take a moment to detect all available devices.

1. Set USB Mode: Select the preferred USB Host Port, from the displayed selection, to use as the currently active connection. The change will occur immediately and all USB Device Ports (USB Type
   • A) on the Transmitter and Receiver will connect to the new host.
   • Note: When “Remote Host” is selected, Host Port 1 on the Transmitter will become active. To select Host Port 2 on the Transmitter, please use the Transmitter’s WebGUI.

Audio Tab

• This tab provides control over the volume level of the balanced analog audio output.
• Note: HDMI audio output is always a direct pass-through from the selected source and is not affected by the controls on this tab.
• Volume: Allows the adjustment of the balanced analog output’s volume level. The available adjustment range is -103 to +24 dB. The analog output may also be muted or unmuted using the toggle switch.
• Note: The analog output can only support LPCM 2.0 sources. Bitstream sources will be automatically muted.

System Tab

• This tab provides system information, network configuration options, system configuration resets, and firmware update functions.

System:

• Web User Setting: This section provides a way to change the password for the Administrator account. Click on “Save” to confirm and activate any changes made to these settings. Note: The default username and password is “admin”.
• Network: The unit’s IP mode may be switched between Static IP or DHCP. In Static IP mode the IP, netmask and gateway addresses may be manually set. When in DHCP mode, the unit will attempt to connect to a local DHCP server and obtain IP, netmask and gateway addresses automatically. Please press “Save” after making any changes to the IP configuration or mode.
• Note: If the IP address is changed then the IP address required for WebGUI/Telnet access will also change accordingly.
• Reset to Default: Press the “Routing Reset” button to reset all I/O routing configurations to the factory defaults. Press the “Factory Reset” button to reset the unit to its factory default state. After the factory reset is complete, the unit will reboot automatically.
• Web   Login Timeout: Select the length of time to wait before logging the user out of the WebGUI due to inactivity. Available range is from 1 to 65535 minutes. Setting this to 0 will disable the inactivity timeout.
• Firmware Upgrade: To update the unit’s firmware, click the Choose File” button to open the file selection window and then select the firmware update file (*.bin format) located on your local PC. After selecting the file, click the “Upgrade” button to begin the firmware update process. After the upgrade is complete, the unit will reboot automatically.

Telnet Control

• Before attempting to use Telnet control, please ensure that both the unit and the PC are connected to the same active networks.

To Access the Command Line Interface (CLI)

Windows 7| Click Start , type “cmd” in the search field, and

press Enter.

Windows XP| Click Start > Run , type “cmd”, and press Enter.
Mac OS X| Click Go > Applications > Utilities > Terminal.

• Once in the Command Line Interface (CLI) type “telnet” followed by the IP address of the unit (and the port number if it is non-standard) and then hit “Enter”. This will connect us to the unit we wish to control
• Note If the IP address is changed then the IP address required for Telnet access will also change accordingly.
• Note 2: The default IP address is 192.168.1.50

RS-232 and Telnet Commands

COMMAND

Description and Parameters
help 8
Show the full command list.
? 8
Show the full command list.
help N1 8
Show help details about command N1.
N1 = {Command}
get model name 8
Show the unit’s model name.
get fw ver 8
Show the unit’s current firmware version.
set factory default 8
Reset all settings to the factory defaults.
set factory ipconfig default 8
Reset the IP configuration to the factory defaults.
set factory out route default 8
Reset output routing to the factory defaults.
set system reboot 8
Reboot the unit.
set ip mode N1 8
Set the IP address assignment mode.
Available values for N1 :
0                                           [Static IP Mode]
1                                           [DHCP Mode]
get ip mode 8
Show the current IP address assignment mode.
COMMAND

Description and Parameters
get ipconfig 8
Show the unit’s current IP configuration information.
set ip addr N1 8
Set the unit’s static IP address.
N1 = X.X.X.X                       [X = 0 ~ 255]
get ip addr 8
Show the unit’s current IP address.
set netmask N1 8
Set the unit’s static netmask.
N1 = X.X.X.X                       [X = 0 ~ 255]
get netmask 8
Show the unit’s current netmask.
set gateway N1 8
Set the unit’s static gateway address.
N1 = X.X.X.X                       [X = 0 ~ 255]
get gateway 8
Show the unit’s current gateway address.
set webgui username N1 8
Set the WebGUI administrator user name.
N1 = {Name}                     [16 characters max]
get webgui username 8
Show the current WebGUI administrator user name
set webgui password N1 8
Set WebGUI administrator password.
N1 = {password}              [16 characters max]
get webgui password 8
Show the current WebGUI administrator password.
COMMAND

Description and Parameters
set webgui login timeout N1 8
Set the WebGUI inactivity timeout value.
Available values for N1 :
0                                           [No timeout]
1 ~ 65535                           [Timeout in minutes]
get webgui login timeout 8
Show the current WebGUI inactivity timeout value.
set in N1 name N2 8
Set the name of the specified input.
N1 = 1 ~ 2                          [Input port]
N2 = {Name}                     [16 characters max]
get in N1 name 8
Show the current name of the specified input.
N1 = 1 ~ 2                          [Input port]
set out N1 name N2 8
Set the name of the specified output.
N1 = A ~ B                          [Output port]
N2 = {Name}                     [16 characters max]
get out N1 name 8
Show the name of the specified output.
N1 = A ~ B                          [Output port]
set out N1 route N2 8
Set the routing of the specified output.
N1 = A ~ B                          [Output port]
N2 = 1 ~ 2                          [Input port]
COMMAND

Description and Parameters
set webgui login timeout N1 8
Set the WebGUI inactivity timeout value.
Available values for N1 :
0                                           [No timeout]
1 ~ 65535                           [Timeout in minutes]
get webgui login timeout 8
Show the current WebGUI inactivity timeout value.
set in N1 name N2 8
Set the name of the specified input.
N1 = 1 ~ 2                          [Input port]
N2 = {Name}                     [16 characters max]
get in N1 name 8
Show the current name of the specified input.
N1 = 1 ~ 2                          [Input port]
set out N1 name N2 8
Set the name of the specified output.
N1 = A ~ B                          [Output port]
N2 = {Name}                     [16 characters max]
get out N1 name 8
Show the name of the specified output.
N1 = A ~ B                          [Output port]
set out N1 route N2 8
Set the routing of the specified output.
N1 = A ~ B                          [Output port]
N2 = 1 ~ 2                          [Input port]
COMMAND

Description and Parameters
get in N1 interlace 8
Show if the source connected to input N1 is interlaced or not.
N1 = 1 ~ 2                          [Input port]
Possible response values:
0                                           [Progressive]
1                                           [Interlaced]
get in N1 sync status 8
Show the detected sync state for input N1.
N1 = 1 ~ 2                          [Input port]
Possible response values:
0                                           [No sync]
1                                           [Sync active]
get in N1 timing 8
Show the resolution and timing index value for input N1’s signal.
N1 = 1 ~ 2                          [Input port]
get in N1 deep color 8
Show the detected color bit depth for input N1’s signal.
N1 = 1 ~ 2                          [Input port]
get in type list 8
List the signal format of all inputs.
get out type list 8
List the signal format of all outputs.
set out route N1N2,N1N2 8
Set unique input routing for both outputs simultaneously.
N1 = A ~ B                          [Output port]
N2 = 1 ~ 2                          [Input port]
COMMAND

Description and Parameters
set all out route N1 8
Set input routing for all outputs.
N1 = 1 ~ 2                          [Input port]
get all out route 8
List the current input routing for all outputs.
set out N1 cec data N2 8
Send a CEC command, as hex data, to the display connected

to the specified output.

N1 = A ~ B                          [Output port]
N2 = {CEC data}              [Comma delimited hex pairs]
get out N1 cec capability 8
Show if the display connected to the specified output supports

CEC.

N1 = A ~ B                          [Output port]
set keylock N1 8
Enable or disable the front panel key lock.
Available values for N1 :
ON                                       [Locked]
OFF                                      [Unlocked]
get keylock 8
Show the current front panel key lock state.
set current route to preset N1 8
Save all current routing assignments to the specified preset.
N1 = 1 ~ 2                          [Preset number]
set route preset N1 8
Activate the routing assignments saved in the specified preset.
N1 = 1 ~ 2                          [Preset number]
COMMAND

Description and Parameters
set all out route N1 8
Set input routing for all outputs.
N1 = 1 ~ 2                          [Input port]
get all out route 8
List the current input routing for all outputs.
set out N1 cec data N2 8
Send a CEC command, as hex data, to the display connected

to the specified output.

N1 = A ~ B                          [Output port]
N2 = {CEC data}              [Comma delimited hex pairs]
get out N1 cec capability 8
Show if the display connected to the specified output supports

CEC.

N1 = A ~ B                          [Output port]
set keylock N1 8
Enable or disable the front panel key lock.
Available values for N1 :
ON                                       [Locked]
OFF                                      [Unlocked]
get keylock 8
Show the current front panel key lock state.
set current route to preset N1 8
Save all current routing assignments to the specified preset.
N1 = 1 ~ 2                          [Preset number]
set route preset N1 8
Activate the routing assignments saved in the specified preset.
N1 = 1 ~ 2                          [Preset number]
COMMAND

Description and Parameters
set all out route N1 8
Set input routing for all outputs.
N1 = 1 ~ 2                          [Input port]
get all out route 8
List the current input routing for all outputs.
set out N1 cec data N2 8
Send a CEC command, as hex data, to the display connected

to the specified output.

N1 = A ~ B                          [Output port]
N2 = {CEC data}              [Comma delimited hex pairs]
get out N1 cec capability 8
Show if the display connected to the specified output supports

CEC.

N1 = A ~ B                          [Output port]
set keylock N1 8
Enable or disable the front panel key lock.
Available values for N1 :
ON                                       [Locked]
OFF                                      [Unlocked]
get keylock 8
Show the current front panel key lock state.
set current route to preset N1 8
Save all current routing assignments to the specified preset.
N1 = 1 ~ 2                          [Preset number]
set route preset N1 8
Activate the routing assignments saved in the specified preset.
N1 = 1 ~ 2                          [Preset number]
COMMAND

Description and Parameters
set all out route N1 8
Set input routing for all outputs.
N1 = 1 ~ 2                          [Input port]
get all out route 8
List the current input routing for all outputs.
set out N1 cec data N2 8
Send a CEC command, as hex data, to the display connected

to the specified output.

N1 = A ~ B                          [Output port]
N2 = {CEC data}              [Comma delimited hex pairs]
get out N1 cec capability 8
Show if the display connected to the specified output supports

CEC.

N1 = A ~ B                          [Output port]
set keylock N1 8
Enable or disable the front panel key lock.
Available values for N1 :
ON                                       [Locked]
OFF                                      [Unlocked]
get keylock 8
Show the current front panel key lock state.
set current route to preset N1 8
Save all current routing assignments to the specified preset.
N1 = 1 ~ 2                          [Preset number]
set route preset N1 8
Activate the routing assignments saved in the specified preset.
N1 = 1 ~ 2                          [Preset number]
COMMAND

Description and Parameters
set in N1 hdcp mode N2 8
Set the HDCP behavior of the specified input.
N1 = 1 ~ 2                          [Input port]
Available values for N2 :
0                                           [Support disabled]
1                                           [Follow source]
2                                           [Follow display]
get in N1 hdcp mode 8
Show the current HDCP behavior used by the specified input.
N1 = 1 ~ 2                          [Input port]
get in N1 hdcp status 8
Show the current HDCP status of the specified input.
N1 = 1 ~ 2                          [Input port]
Possible response values:
0                                           [No HDCP]
1                                           [HDCP 1.x]
2                                           [HDCP 2.2]
get out N1 hdcp status 8
Show the current HDCP status of the specified output.
N1 = A ~ B                          [Output port]
Possible response values:
0                                           [No HDCP]
1                                           [HDCP 1.x active]
2                                           [HDCP 2.2 active]
3                                           [HDCP 1.x failed]
4                                           [HDCP 2.x2 failed]
COMMAND

Description and Parameters
set in N1 hdcp mode N2 8
Set the HDCP behavior of the specified input.
N1 = 1 ~ 2                          [Input port]
Available values for N2 :
0                                           [Support disabled]
1                                           [Follow source]
2                                           [Follow display]
get in N1 hdcp mode 8
Show the current HDCP behavior used by the specified input.
N1 = 1 ~ 2                          [Input port]
get in N1 hdcp status 8
Show the current HDCP status of the specified input.
N1 = 1 ~ 2                          [Input port]
Possible response values:
0                                           [No HDCP]
1                                           [HDCP 1.x]
2                                           [HDCP 2.2]
get out N1 hdcp status 8
Show the current HDCP status of the specified output.
N1 = A ~ B                          [Output port]
Possible response values:
0                                           [No HDCP]
1                                           [HDCP 1.x active]
2                                           [HDCP 2.2 active]
3                                           [HDCP 1.x failed]
4                                           [HDCP 2.x2 failed]

Note: Commands will not be executed unless followed by a carriage return. Commands are not case-sensitive.

CONNECTION DIAGRAM

SPECIFICATIONS

Technical Specifications

• HDMI Bandwidth 18Gbps
• HDBaseT Bandwidth 10.2Gbps
• Input Ports 1×HDMI (Type-A)
  • 1×HDBaseT (RJ-45)
• Output Ports 2×HDMI (Type-A)
  • 1×Balanced Stereo (5-pin Term. Block)
• Pass-through Ports 1×IR Extender (3.5mm)
  • 1×IR Blaster (3.5mm)
  • 2×USB 2.0 (Type A)
  • 1×USB 2.0 (Type B)
  • 1×RS-232 (3-pin Terminal Block)
• Pass-through/Service Port 1×USB 2.0 (Type A)
• Pass-through/Control Port 1×LAN (RJ-45)
• Control Port 1×RS-232 (3.5mm)
• IR Frequency 30 – 50kHz
  • (30 – 60kHz under ideal conditions)
• Baud Rate (Control) 19200 (Default)
• Baud Rate (Bypass) Up to 115200
• Power Supply 24V/3.75A DC
• (US/EU standards, CE/FCC/UL certified)
• ESD Protection (HBM) ±8kV (Air Discharge) ±4kV (Contact Discharge)
• Dimensions (W×H×D) 231.5mm×44mm×160mm [Case Only] 231.5mm×44mm×167mm [All Inclusive]
• Weight 928g
• Chassis Material Metal (Steel)
• Chassis Color Black
• Operating   Temperature 0˚C – 40˚C/32˚F – 104˚F
• Storage Temperature -20˚C – 60˚C/-4˚F – 140˚F
• Relative Humidity 20 – 90% RH (Non-condensing)
• Power Consumption 22.33W

Video Specifications

Supported Resolutions (Hz)

| Input| Output
---|---|---
HDMI| HDBaseT| HDMI
1920×1200p@60RB| | |
2560×1440p@60RB| | |
2560×1600p@60RB| | |
2048×1080p@24/25/30| | |
2048×1080p@50/60| | |
3840×2160p@24/25/30| | |
3840×2160p@50/60 (4:2:0)| | |
3840×2160p@24, HDR10| | |
3840×2160p@50/60 (4:2:0), HDR10| | |
3840×2160p@50/60| | |
4096×2160p@24/25/30| | |
4096×2160p@50/60 (4:2:0)| | |
4096×2160p@24, HDR10| P| | P
4096×2160p@50/60 (4:2:0), HDR10| P| | P
4096×2160p@50/60| P| | P

Audio Specifications

Digital Audio

HDMI Input / Output

LPCM
Max Channels| 8 Channels
Sampling Rate (kHz)| 32, 44.1, 48, 88.2, 96, 176.4, 192
Bitstream
Supported Formats| Standard & High-Definition
HDMI Input / Output

LPCM
Max Channels| 8 Channels
Sampling Rate (kHz)| 32, 44.1, 48, 88.2, 96, 176.4, 192
Bitstream
Supported Formats| Standard & High-Definition

Analog Audio

Analog Output

Max Audio Level| 1Vrms
THD+N| < −80dB@0dBFS 1kHz (A-wt)
SNR| > 80dB@0dBFS
Frequency Response| < ±1dB@20Hz~20kHz
Crosstalk| < −80dB@10kHz
Impedance| 470Ω
Type| Balanced

Cable Specifications

Cable Length

| 1080p| 4K30| 4K60
---|---|---|---

8-bit

| ****

12-bit

| (4:4:4)

8-bit

| (4:4:4)

8-bit

High Speed HDMI Cable
HDMI Input| 15m| 10m| 5m| 3m
HDMI Output| 15m| 10m| 5m| 3m
Ethernet Cable
Cat.5e/6| 100m| 90m
Cat.6a/7| 100m| 100m

Bandwidth Category Examples:

• 1080p (FHD Video)
• Up to 1080p@60Hz, 12-bit color
• Data rates lower than 5.3Gbps or below 225MHz TMDS clock

4K30 (UHD Video)

• 4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit color
• Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps

4K60 (UHD+ Video)

• 4K@50/60Hz (4:4:4, 8-bit)
• 4K@50/60Hz (4:2:0, 10-bit HDR)
• Data rates higher than 10.2Gbps

HDBaseT Features

ACRONYMS

ACRONYM             COMPLETE TERM

ADC| Analog-to-Digital Converter
ASCII| American Standard Code for Information

Interchange

AV| Audio/Video
Cat.5e| Enhanced Category 5 cable
Cat.6| Category 6 cable
Cat.6a| Augmented Category 6 cable
Cat.7| Category 7 cable
CLI| Command-Line Interface
DAC| Digital-to-Analog Converter
DHCP| Dynamic Host Configuration Protocol
DP| DisplayPort
DVI| Digital Visual Interface
EDID| Extended Display Identification Data
GUI| Graphical User Interface
HD| High-Definition
HDBT| HDBaseT
HDCP| High-bandwidth Digital Content Protection
HDMI| High-Definition Multimedia Interface
HDR| High Dynamic Range
HDTV| High-Definition Television
IP| Internet Protocol
IR| Infrared
KVM| Keyboard/Video/Mouse
LAN| Local Area Network
LED| Light-Emitting Diode
LPCM| Linear Pulse-Code Modulation
MAC| Media Access Control
ACRONYM| COMPLETE TERM
---|---
PD| Powered Device
PoH| Power over HDBaseT
PSE| Power Sourcing Equipment
SNR| Signal-to-Noise Ratio
TCP| Transmission Control Protocol
THD+N| Total Harmonic Distortion plus Noise
UHD| Ultra-High-Definition
UHD+| Ultra-High-Definition Plus
UHDTV| Ultra-High-Definition Television
USB| Universal Serial Bus
VGA| Video Graphics Array
WUXGA (RB)| Widescreen Ultra Extended Graphics Array

(Reduced Blanking)

XGA| Extended Graphics Array

• CYPRESS TECHNOLOGY CO., LTD.
• www.cypress.com.tw

Documents / Resources

| CYP CH-2603TX HDMI HDBaseT USB to HDMI Receiver [pdf] User Manual
CH-2603TX, CH-2603RX, CH-2603TX HDMI HDBaseT USB to HDMI Receiver, HDBaseT USB to HDMI Receiver, USB to HDMI Receiver, HDMI Receiver, Receiver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>