American Blinds Basic Custom Traversing Drapery Hardware Instruction Manual
- June 13, 2024
- American Blinds
Table of Contents
American Blinds Basic Custom Traversing Drapery Hardware
Product Information
The Forest Drapery Track System is a versatile and easy-to-install hardware solution for hanging draperies. It can be mounted on the wall or ceiling, depending on your preference and needs. The track is designed to hold and traverse drapery panels smoothly, allowing for easy opening and closing.
Key Features:
- Sturdy and durable construction
- Compatible with various drapery styles and weights
- Easy installation with step-by-step instructions
- Adjustable brackets for precise positioning
- Option to splice multiple track pieces for wider areas
- Baton control option for convenient operation
Getting Started
Please read through all instructions carefully before you begin.
Unpack all materials making sure all components are included:
- Track(s)
- Master carrier(s) & carriers (pre-installed within track)
- Mounting brackets
- Splice, if requested
Tools You Will Need:
- Drill with a 1/8” bit and a Phillips bit
- Phillips screwdriver
- Screws for mounting brackets
- Metal tape measure
- Hack saw (optional)
Wall Mount Instructions
Installing Your Drapery Track:
You are now ready to install your Forest Drapery Track System.
-
Measure
Determine the height of the top of track and mark bracket height on the wall for all the brackets and adjust (as necessary) to make sure they are all leveled. -
Mark
Measure the width of the track and mark the two end brackets approximately 3”- 4” in from the ends of the track. Evenly space the remaining brackets and place corresponding marks. -
Mount
To attach the bracket to the wall; first pre-drill holes for screw diameter when mounting into wood frame of window or wall stud. Otherwise, pre-drill and install anchors first before fastening with screws. -
Attach Bracket
Place the track into the bracket as shown in the drawing; applying pressure until track “clicks” into bracket. Make sure track set screw is loose enough to allow the track retainer to flex. Repeat this step for the remaining brackets. -
Tighten
Tighten track set screws on all the brackets to secure track to brackets. -
Adjust Projection
Adjust track to the desired projection. Projection is adjustable from 3” – 4 ½”. Repeat this step for the remaining brackets.
Once desired projection is set for all the brackets, lock the bracket into position by tightening the track depth adjustment set screw (see drawing below).
Installing Splice, if requested:
For wide areas, tracks will be shipped in multiple pieces and will require
a splice.
- Slide the track of the connecting ends on each track into the channel of the splice and butt ends together.
- Tighten locking screw with hex key for a secure fit.
Ceiling Mount Instructions
Installing Your Drapery Track:
You are now ready to install your Forest Drapery Track System.
-
Measure
Measure the width of the track and mark the two end brackets approximately 3”- 4” in from the ends of the track. Evenly space the remaining brackets and place corresponding marks. -
Mount
To attach the bracket to the ceiling; first pre-drill holes for screw diameter when mounting into wood frame of window or wall stud. Otherwise, pre-drill and install anchors first before fastening with screws. -
Attach Bracket
Place the track into the bracket as shown in the drawing; applying pressure until track “clicks” into bracket. Make sure track set screw is loose enough to allow the track retainer to flex. Repeat this step for the remaining brackets. -
Tighten
Tighten track set screws on all the brackets to secure track to brackets.
Installing Splice, if requested:
For wide areas, tracks will be shipped in multiple pieces and will require
a splice.
- Slide the track of the connecting ends on each track into the chanel of the splice and butt ends together.
- The tracks will snap together. Press together and confirm a tight fit.
- Secure with additional screw.
Installling Drapery Baton: (Baton Control Only)
You may attach a baton(s) to the master carrier(s). Simply fit the metal hook
on the baton through the slot on the master carrier.