yOSHIMURA 070BG137200 Fender Eliminator Kit User Guide

yOSHIMURA 070BG137200 Fender Eliminator Kit

Product Information

• Product Name: Fender Eliminator Kit
• Manufacturer: Yoshimura R&D of America, Inc.
• Model: 070BG137200
• Compatibility: Yamaha R7
• DOT Approval: Not approved
• Website: www.yoshimura-rd.com

THIS PRODUCT IS NOT DOT APPROVED.
Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the installation of this product. Check with local laws and regulations for compliance prior to installation and use. This product is not intended for use on public highways

PARTS

Optional Parts
***| 070BGUNVTBKT| Universal Turn Signal Bracket Kit

Removal

1. Remove passenger and rider seats.
2. Remove the center cover between the passenger and rider seats.
3. Remove the upper tail cover above the tail light.
4. Remove left and right rear side covers as per Factory Service / Owners Manual.
5. Disconnect license plate light and turn signal connectors.
6. While securely supporting the stock fender assembly, remove the four bolts securing the fender assembly to the subframe. Carefully remove the stock fender assembly making sure not to damage the license plate light wire and turn signal connectors.
7. Disassemble the stock fender assembly and remove left and right turn signals.
8. Cut the stock license plate light connector from the stock fender assembly. Be sure to cut at least a 6” section of wire from the connector

Installation

1. Install (No. 3) 070BG-LH-K1, Yoshimura license plate light onto (No. 2) 070BG-UNV-FEBKT, Yoshimura license plate bracket using (No. 10) M4X6BHS, 4mm button head sc

2. Install (No. 13) H-2158, dust grommet onto (No. 1) 13720-FEBKT, fender eliminator bracket by pushing the grommet into the top plate of the bracket.

3. Install (No. 2) 070BG-UNV-FEBKT, license plate bracket onto (No. 1) 13720-FEBKT, fender eliminator bracket using (No. 9) M6X10BHS, 6mm button head screw.

4. Install (No. 1) 13720-FEBKT, fender eliminator bracket to the subframe using the stock bolts.

5. Using the BN-SSS-22-18, solder shrink connectors provided in the kit, connect Yoshimura license plate light wires to the stock license plate light wires as follows:

   • Red -to- Blue
   • Black -to- Black
   • a) Strip the stock fender light wire ends 1/4” – 1/2” and insert into BN-SSS-22-18, solder shrink connectors provided in the kit.
   • b) Center the spliced wire ends in the middle and using a heat gun or lighter, apply heat evenly on the outer edges of the solder shrink connectors to shrink and hold wires in place.
   • c) Making sure that the stripped ends are centered, heat the center of the butt connector evenly until the solder begins to liquefy.
   • d) Allow to cool completely and tug both ends of the wires to verify that the connection is secured.
     Scan for a link to the solder shrink connectors instruction video.

6. Install the stock left and right turn signals onto (No. 5,6) 13992-TSB-L/R, turn signal brackets using the stock hardware.

7. Install (No. 5,6) 13992-TSB-L/R, turn signal brackets and (No. 4) 070BG-LPF, license plate frame using the (No. 7,8) M6X16BHS and M6X14BHS, 6mm button head screws and secure with (No.11,12) 6MMWASHER and 6MMLN, 6mm washer and 6mm locking nut as shown in the diagram.

8. Route the license plate light and turn signal wires through the (No. 13) H-2158, dust grommet, under the passenger seat, and reconnect.

9. Re-install the left and right rear side covers using the reverse steps of removal.

10. Re-install the upper tail cover.

11. Re-install the center cover.

12. Re-install the rider and passenger seats.

13. Check for proper function of license plate light, turn signals, brake light, and that all brackets and components are secure prior to riding

CONTACT

• ADDRESS: 5420 DANIELS STREET STE A, CHINO CA., 91710 ·
• TELL: (800)634-9166 · (909)628-4722 ·
• FAX (909)591-2198

References

• Yoshimura R&D – Yoshimura R&D of America, Inc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>