YOSHIMURA SA-19-K Spark Arrestor Kit Instruction Manual
- June 10, 2024
- YOSHIMURA
Table of Contents
YOSHIMURA SA-19-K Spark Arrestor Kit
Product Information
Yoshimura TEC-SD15 Spark Arrestor Kit
The Yoshimura TEC-SD15 Spark Arrestor Kit is a safety accessory designed for use with Yoshimura exhaust systems. The kit includes a spark arrestor, spark arrestor ring, button head screw, lock nut, and USFS-certified spark arrestor label. The spark arrestor is designed to reduce the risk of fire by trapping hot particles in the exhaust system.
Parts Diagram
NO. | DESCRIPTION | QTY | PART # |
---|---|---|---|
1 | 5mm X 18mm Button Head Cap Screw | 1 | M5X18BHS |
2 | RS-12 Spark Arrestor Ring 1.375 | 1 | YM1-RING-1375 |
3 | TEC-SD15 Spark Arrestor | 1 | TEC-SD15-01 |
4 | 5mm Lock Nut | 1 | 5MMLN-U |
5 | Yoshimura Exhaust | n/a | n/a |
** | USFS Label | 1 | 17082 |
Product Usage Instructions
- Remove the button head screw securing the aluminum ring and spark arrester to the muffler and remove the spark arrester.
- Using a wire brush, remove carbon deposits from the spark arrester screen. Inspect the screen for excessive wear or damage. If a spark arrester is excessively worn or damaged, the spark arrester must be replaced. Cleaning and inspection should be performed after every 60 hours of use. Caution: Gloves and safety glasses should be worn while cleaning the spark arrester.
- Re-install the spark arrester and aluminum ring.
- Note: It is recommended that a low-strength Loctite is used on the spark arrester securing bolt.
- Apply the USFS-certified spark arrester label on the muffler where visible.
It is important to regularly clean and inspect the spark arrestor to ensure it
is functioning properly and reducing the risk of fire. The Yoshimura TEC-SD15
Spark Arrestor Kit should only be installed by a qualified mechanic or
technician familiar with exhaust system installation. For more information or
assistance, please visit
www.yoshimura-rd.com.
Parts Diagram
NO. | DESCRIPTION | QTY | PART # |
---|---|---|---|
1 | 5mm X 18mm Button Head Cap Screw | 1 | M5X18BHS |
2 | RS-12 Spark Arrestor Ring 1.375″ | 1 | YM1-RING-1375 |
3 | TEC-SD15 Spark Arrestor | 1 | TEC-SD15-01 |
4 | 5mm Lock Nut | 1 | 5MMLN-U |
5 | Yoshimura Exhaust | ** | ** |
** | USFS Label | 1 | 17082 |
- Remove button head screw securing the aluminum ring and spark arrester to the muffler and remove spark arrester.
- Using a wire brush, remove carbon deposits from spark arrester screen. Inspect the screen for excessive wear or damage. If spark arrester is excessively worn or damaged, the spark arrester must be replaced. Cleaning and inspection should be performed after every 60 hours of use.
- Caution: Gloves and safety glasses should be worn while cleaning spark arrester.
- Re-install spark arrester and aluminum ring.
- Note: It is recommended that a low strength “Loc-tite” is used on the spark arrester securing bolt.
- Apply USFS certified spark arrester label on muffler where visible.
- RESEARCH &DEVELOPMENT OF AMERICA, INC.
- 5420 DANIELS STREET SUITE A, CHINO, CA 91710
- 800-634-9166
- 909-628-4722
- FAX909-591-2198
- www.yoshimura-rd.com
Documents / Resources
|
YOSHIMURA SA-19-K Spark Arrestor
Kit
[pdf] Instruction Manual
SA-19-K, SA-20-K, SA-19-K Spark Arrestor Kit, SA-19-K, Spark Arrestor Kit,
Arrestor Kit
---|---