HOOKER GEN3 Hemi Swap Engine Mountsa Instruction Manual
- June 13, 2024
- HOOKER
Table of Contents
HOOKER GEN3 Hemi Swap Engine Mountsa Instruction Manual
Thank you for choosing to use Hooker Blackheart™ engine swap mounts as part of
your GEN3 HEMI Swap project. These mounts are part of the most comprehensively
engineered system of mounting components, headers and exhaust systems
available for this application. Please read these instructions thoroughly
before attempting installation.
IMPORTANT: Low mount A/C Compressors will only work with engines using VVT
front accessory drive. *** These engine mounts will not work with NON-VVT low
mount A/C compressor configurations. Column shift vehicles with manual
steering will require modifications to the steering column tube and shift
linkage bracket for valve cover clearance.
PRE-INSTALLATION CONSIDERATIONS:
-
Mopar 90 degree oil filter adapter PN: 04893315AC or remote oil filter location will be required.
-
Use of a Mid Sump oil pan and pick up tube required (Holley PN: 302-61 VVT or PN: 302-60 NON-VVT – See www.holley.com
for a complete selection of Hemi Swap oil pans and pickup tubes) NOTE: Some K-members require minor clearance for oil pan fitment. -
6.2L Hellcat engine installations may require supercharger water manifold PN: HEMI0005ERL.
-
Only Blackheart Headers PN: BH23104 headers have been tested for correct fitment with these engine mounting plates.
Visit www.holley.com for a complete selection of transmission crossmember, headers, exhaust, and more GEN3 HEMI support products to complete your A-Body Hemi Swap.
COMPATIBILITY INFORMATION:
PN: BHS571 Engine Mounts will not work with the following combinations:
- Low mount A/C Compressors on NON-VVT ENGINES – (VVT timing cover and accessory drive is required to use low mount A/C)
- OEM Hemi K-Members
- 6 Cylinder K-Members
- Early K-Members using pad style engine mounts (67-72)
PARTS LIST:
ACCESSORY PACK CONTENTS
Check the hardware package. If anything is missing, please contact Technical Service at 1-866-464-6553 or 270-781-9741.
TOOLS NEEDED:
INSTALLATION OF BHS571 GEN 3 HEMI SWAP ENGINE MOUNTS:
Driver’s Side Mounting Plate
- With the engine out of the vehicle, install the driver’s side (Left) engine mount to the engine block using (x4) M10 x 25mm flange bolts provided. Install the mount with the polyurethane mount toward the front of the engine using the OEM engine mount locations on the engine block. NOTE: The 5th mounting hole provided may be used in place of the 4th bolt under the
motor mount pad, if the block is threaded. NOTE: Always use at least 4 mounting bolts (Figures 1 & 2).
Passenger’s Side Mounting Plate
- With the engine out of the vehicle, install the driver’s side (Left) engine mount to the engine block using (x4) M10 x 25MM flange bolts provided. Install the mount with the polyurethane mount toward the front of the engine using the OEM engine
mount locations on the engine block. NOTE: Always use at least 4 mounting bolts (Figures 3 & 4).
- Install the 1/2″ x 5″ bolt with one flat washer into the engine mount. Install the bolt into the mount from the front for the left and right mounts. Install a second flat washer and locking nut on to the bolt.
- Slowly lower the engine onto the mounts being careful not to get the polyurethane bushing or flat washers caught on the edge of the engine mounting stand as the mount passes into the stand.
- Check be sure the bolt is seated in the stand completely and tighten the nut. Note: Support the engine while the transmission is being installed to avoid damaging the polyurethane bushing
Any questions? Please contact Technical Service:
1-866-464-6553 or
270-781-9741. For online help, please
refer to: www.holley.com.
© 2021 Hooker Headers, Inc. All rights reserved. Tous Droits Réservés.
199R12169 Date: 3-4-21
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>