HOOKER BLACKHEART BHS591 8HP90 8 Speed Automatic Transmission Instruction Manual
- June 3, 2024
- HOOKER BLACKHEART
Table of Contents
HOOKER BLACKHEART BHS591 8HP90 8 Speed Automatic Transmission
Installation Instructions
Thank you for choosing to use HOOKER™ engine swap mounting brackets as part of
your GEN3 HEMI Swap project. These mounting brackets are part of the most
comprehensively engineered system of mounting components, headers, and exhaust
systems available for this application. Please read these instructions
thoroughly before attempting installation.
IMPORTANT: Requires Hooker Blackheart Engine Mounting Brackets P/N
BHS566, 2 bolt Chevy Transmission mount P/N 71223029HKR, and Transmission
Crossmember P/N: BHS567
Will not work with 8HP70 8 Speed Automatic – Use PN: BHS570 Adapter Plate
Visit www.holley.com for a complete selection of Transmission Crossmember ,Headers ,Exhaust and more GEN3 HEMI support products to complete your E-Body Hemi Swap.
COMPATIBILITY INFORMATION
70-74 E-Body Mopar cars using GEN3 HEMI engines, installing the following transmission and using the listed supporting parts.
8HP90 (8 SPEED AUTOMATIC): Crossmember P/N: BHS567, Transmission mount P/N: 71223029HKR, and Engine Mounting Brackets P/N: BHS566.
Install Notes: Some transmission tunnel and pinch weld at firewall massaging will be required, minor trimming of unused- nonstructural casting flash, and tabs will be required to the transmission case. Manual park release cable bracket may need to be fabricated. Output flange adaptor, custom drive shaft and shifter fabrication are required.
PARTS LIST
Qty. | Description |
---|---|
1 | Transmission Adapter Plate |
ACCESSORY PACK CONTENTS
4 | M10 x 1.25 x 25mm Flange Bolts | |
---|---|---|
2 | 7/16-14 x 1” Flange Bolt | |
2 | 7/16-14 Flange Nut | |
2 | 599R94 | Decal – Blackheart 2” x 4” |
1 | 199R12233 | Instruction Sheet |
Check the hardware package. If anything is missing, please contact Technical Service at 1-866-464-6553 or 270-781-9741.
TOOLS NEEDED
3/8” Drive Socket Set
3/8” Drive Metric Socket Set
11/16 Wrench
5/8 Wrench
INSTALLATION
These instructions assume the engine and transmission are installed.
-
Install the Hooker Blackheart Transmission Adapter Plate on to the transmission tailshaft using the (x4) supplied M10 x 25mm bolts. Tighten the bolts. NOTE: Torque M10 bolts to approximately 30 ft./lbs. DO NOT over tighten.
-
Install the Transmission Mount to the Transmission Adapter Plate with the (x2) 7/16 x 1” bolts and nuts supplied in the Adapter Plate Kit.
NOTE: The Transmission Mount will be installed between the Adapter Plate and the BHS567 Transmission Crossmember (Figure 1). -
Install the BHS567 (SOLD SEPARATELY) crossmember and align the studs of the transmission mount while raising the transmission crossmember into position. Align the bolt holes and install the provided 3/8-16 x 3.5” bolts with washers. Install the provided flange nuts and tighten. Align the transmission to center. Install the nuts onto the transmission mounts and tighten.
Shown with 8HP90 Transmission Installed
Any questions? Please contact Technical Service:
1-866-464-6553 or
270-781-9741. For online help, please
refer to: www.holley.com.
© 2021 Hooker Headers, Inc. All rights reserved. Tous Droits Réservés.
199R12233
Date: 5-26-21
BHS591 Adapter Plate
BHS567 Crossmember
71223029HKR Trans Mount
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>