GREENBROZ 844 The Harvest Bucket User Guide
- June 13, 2024
- GreenBroz
Table of Contents
GREENBROZ 844 The Harvest Bucket
Product Information
The Harvest Bucket is a trimming machine designed for efficient and safe
trimming of plants. It is made up of food safe materials, including surgical
316 stainless steel, ensuring durability and hygiene. The machine has rotating
parts and pinch points that can cause serious injury, so it is important to
follow the safety instructions and precautions provided.|
The dimensions of the Harvest Bucket are 34.4 cm (13.58) x 34.4 cm (13.58) x
39.6 cm (15.62), and it weighs 5.4 Kg (12 lbs.). The ideal speed of operation
is between 20-40 RPM.
Product Usage Instructions
Safety Instructions
- Users should never place their hands into the bucket during operation.
- If the user needs to put their hands into the trimming area, the drill must be detached from the trimming shaft and safely stored away from the bucket.
- Ensure that all guards, assemblies, and accessories are properly installed before powering the machine.
- Absolutely no loose hair, clothes, jewelry, or accessories are permitted when operating.
- Never place hands or head near the machine during operation.
Assembly Instructions
Step One: Bucket Clamp Assembly
- Take the Bucket Clamp and insert the Internal Bucket into one half of the clamp.
- Place that same half of the clamp on the five-gallon bucket.
- Once both items are seated in half of the clamp, rotate the other half closed and secure the latch.
Step Two: Blade and Trimming Plate Installation
- After clamping the Internal Bucket and the five-gallon bucket together, install the top and bottom blades by dropping them into place.
- Ensure that the bottom blade is placed first and that the blades are facing opposite directions.
- Next, place the Trimming Plate into the triangular cutouts on the bucket clamp and fix it in place with the supplied thumb screws.
Trimming
To trim plants using the Harvest Bucket:
- Refer to the provided video guide for detailed instructions on operating the Harvest Bucket.
Bucking
If your bucket has a bucking feature built into the clamp, follow these steps:
- Using the side of the clamp with beveled edges, thread the bottom of the plant through the provided holes.
- Hold the same side of the clamp that is being used to buck.
Cleaning Instructions
To clean the Harvest Bucket:
- The machine can be broken down for general cleaning without any tools required.
- For a deeper clean of each component, use a 7/16 wrench and a flat head screwdriver.
- Pay special attention to the surfaces that come in direct contact with your material.
- The stainless-steel components can be power washed and sanitized with chemicals as needed.
- Avoid using chemicals and high-pressure water on the plastic components; instead, use soap, water, and a rough sponge.
For further assistance or inquiries, contact GreenBroz at
844.DRY.TRIM or
info@greenbroz.com. Additional information can be
found at greenbroz.com.
SCAN QR Code to see the How to Asseble the Harvest Bucket Video
SAFETY INSTRUCTIONS
Users shall never place their hands into the bucket during operation. If, at any time, the user needs to put their hands into the trimming area the drill must be detached from the trimming shaft and safely stored away from the bucket.
- This machine has rotating parts and pinch points that can cause serious injury. When powering the machine, ensure that all guards, assemblies, and accessories have been properly installed. Absolutely no loose hair, clothes, jewelry, or accessories permitted when operating.
ROTATING MECHANICAL PARTS
Rotating machine parts have the potential to cause severe injury or death. All
components must be fully secured before operation and are essential for
protecting operators. Never place hands or head near the machine during
operation.
TECHNICAL SPECIFICATIONS
- Dimensions: 34.4 cm (13.58”) x 34.4 cm (13.58”) x 39.6 cm (15.62”)
- Weight : 5.4 Kg (12 lbs.)
- Ideal speed : 20-40 RPM
- Construction : Made up of food safe materials, inlcuding surgical 316 stainless steel
OPERATING INSTRUCTIONS
Trimming:
After properly assembling the Bucket Trimmer, as shown in the assembly portion of this manual, the drill is able to be attached. The trimming shaft is able to be fixed to the drill like any normal drill bit. Open the chuck until the hex shaft slides in and then full tighten down while making sure the shaft is not crooked. The shaft is now able to be slid into place for trimming. Ensure the shaft is fully recessed into both plastic seats before operating. With the shaft in place, rotate clockwise at low RPM until you have your desired finish. Note: High RPM can cause damage to the machine or material.
Bucking:
Some buckets come with a bucking feature built into the clamp itself. There
are various different geometries that will work for most sized plants. Using
the side of the clamp with beveled edges, it is recommended to simply thread
the bottom of the plant through the provided holes and pull through manually.
Ensure to hold the same side of the clamp that is being used to
buck.
SCAN QR Code to see the How to Operate Harvest Bucket Video
CLEANING INSTRUCTIONS
Tools required for deep cleaning: 7/16” wrench & flat head screwdriver
The machine breaks down for general cleaning without any tools required. For a
deeper clean of each of the components, the tools listed above are required.
The surfaces that come in direct contact with your material should be paid
special attention to. The stainless-steel components are able to be power
washed and sanitized with chemicals as needed. Keep chemicals and high-
pressure water away from the plastic components when cleaning, soap and water
with a rough sponge is recommended.
Assembly Instructions Step One:
The Bucket Clamp has two imbedded slots labeled below. The larger radius is
designed to grab the top rim of the five-gallon bucket and the smaller radius
holds the Internal Bucket as shown below. Take the clamp and insert the
internal bucket into one half and place that same half on the five-gallon
bucket. Once both items are seated in half of the clamp, rotate the other half
closed and secure the latch.
Assembly Instructions Step Two:
Once the Internal Bucket and the five-gallon bucket have been clamped
together, the blades and the Trimming Plate can be installed. Both the top and
bottom blades are able to be just dropped into place. It is important to note
that the bottom blade is placed first and that the blades should be facing
opposite directions as shown below. Next, place the trimming plate into the
triangular cutouts on the bucket clamp and fix it in place with the supplied
thumb screws.
Assembly Instructions Step Three:
The final step of assembly is to just drop in the rest of the items. The shaft
and GBZ tines are completely removable. Ensure to place the GBZ tines so that
their faces are resting on the Trimming Plate as shown below. Fix your drill
to the 3/8” hex shaft and rotate clockwise at low RPM until you have your
desired finish.
SCAN QR Code to see the How to Asseble the Harvest Bucket Video
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>