LUTEC 101148 Semi Flush 6 Light Fitting Instruction Manual
- June 13, 2024
- LUTEC
Table of Contents
LUTEC 101148 Semi Flush 6 Light Fitting
Product Information
The Semi Flush Light Fitting is a lighting product designed for indoor use. It is manufactured by Brilliant AG, a company based in Gnarrenburg, Germany. The product model number is 101148_08062023. The UK manufacturer’s address is BH17 7BY.
Safety Warnings
- Never put anything on the product or hang anything on any part of this product.
- Ensure that all electrical connections are tight and no loose strands are left out of the terminal.
- Do not fit bulbs of a higher wattage than specified on the label to avoid overheating and damage to the fitting.
- Dispose of waste electrical products properly through recycling facilities. Contact your Local Authority or local store for recycling advice
Care and Maintenance
- Switch off the product before replacing the bulb (preferably, isolate it at the distribution board) and allow it to cool down as the bulb gets hot during use.
- Clean the product with a dry cloth only. Do not use liquid or abrasive cleaners.
Troubleshooting
If the bulb does not light after installation, follow these steps:
- Ensure that there is no electricity failure.
- Check that all connections are secure.
- If you have any doubts about installation or usage, consult a qualified electrician.
Assembly Instructions
The assembly instructions are provided in the form of a numbered diagram:
Please refer to the diagram to assemble the product correctly.
For any further inquiries or assistance, please contact the manufacturer.
Installation and Safety Instructions
Semi Flush Light Fitting
Safety Warnings
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference. If you are in any doubt about
installing this product, consult a qualified electrician.
This product is only suitable for connection to a 220-240V~ 50Hz supply in
accordance with current IEE wiring regulations, and should be installed in
accordance with local building regulations. It is for domestic ceiling use
only, and is not suitable for a bathroom location.
This is a Class l product and must be Earthed. The terminal blocks are
supplied according to requirements of the fitting.
IMPORTANT: Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.
The product must be securely fixed to the mounting surface using the screws
and wall plugs supplied. The screws and wall plugs supplied are suitable for
“masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove existing light fitting.
Note the position of the electrical connections, and ensure there is a solid
mounting surface, Preferably a wooden joist or joist bridge, to support the
weight of the light fitting.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
Never put anything on the product or hang anything on any part of this
product.
IMPORTANT: Ensure that all electrical connections are tight and that no
loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as
these may cause over heating and damage the fitting).
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the
distribution board) and allow it to cool down (Caution: bulb gets hot during
use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this
product.
Troubleshooting
When the bulb does not light after installation:
- Ensure there is no electricity failure.
- Ensure all the connections are secure.
If you have any doubt about installation/use of this product, consult a qualified electrician.
Assembly Instructions
Scan QR code for multi-language
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brillantstrasse 1, D-27442 Gnarrenburg