LIEBHERR SFT 1223 Supermarket Cabinet Instruction Manual

SFT 1223 Supermarket Cabinet
Instruction Manual

SFT 1223 Supermarket Cabinet

Operating instructions
Supermarket cabinet
Read the operating instructions before switching it on for the first time
SFT 1223 SFT 1023
7084 822-02
Description of the appliance

Safety instructions and warnings

• If there is obvious transport damage on the appliance after it has been unpacked, contact the supplier. Do not start the appliance.
• Disconnect the appliance from the mains if any fault occurs. Trip the fuse upstream of the appliance. Transfer food to other appliances.
• Only carry out repair and other work on the appliance when the mains plug has visibly been disconnected.
• Any repairs and work on the appliance should only be carried out by the customer service department, as unauthorised work could prove highly dangerous for the user. The same applies to changing the main power cable.
• Do not allow naked flames or ignition sources to enter the appliance. When transporting and cleaning the appliance, ensure that the refrigerant circuit is not damaged. In the event of damage, make sure that there are no ignition sources nearby and keep the room well-ventilated.
• Avoid prolonged skin contact with cold surfaces or chilled/frozen food. This could cause pain, numbness, and frostbite. In the case of prolonged skin contact, protective measures should be taken, e.g. gloves should be worn.
• Do not store food whose use-by date has expired in the appliance. Eating such goods can cause food poisoning.
• Do not store explosive substances or spray cans with inflammable propellants in the appliance. Electrical components might cause leaking gas to ignite.
• Do not use electrical appliances inside the appliance.
• The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.
• The LED light strips illuminate the interior of the appliance. They are not suitable for lighting a room.
• Do not place any objects on the appliance.
• Do not use any mechanical devices or other artificial aids for defrosting other than those recommended by the manufacturer.
• Do not cover the ventilation openings.
• Ensure that the refrigerant circuit pipes will not be damaged.

Disposal instructions for packaging material
WARNING Danger of suffocation due to packing material and plastic film!
Do not allow children to play with packaging material.
Dispose of the packaging material in compliance with current regulations.
Range of appliance use
This appliance is only suitable for storing food that has already been frozen.
The appliance is not suitable for freezing fresh food.
Any misuse of the appliance may result in damage to or spoilage of stored goods.
Appliance dimensions

| Width [mm]| Height [mm]| Depth withhandle [mm]
---|---|---|---
SFT 1223| 2500| 1283| 710
SFT 1023| 2100| 1283| 710

Important
The maximum load per grid shelf is 25 kg.
No more than two grid shelves may be fitted one above the other.
Maximum appliance load: 300 kg
EPREL database
As of 1 March 2021, information about energy labeling and ecodesign requirements will be available in the European product database (EPREL). You can access the product database using the following link: https://eprel.ec.europa.eu/. You will be asked to enter the model identifier. You will find the model identifier on the type plate.

Climate class

The climate class [X] specifies the ambient conditions in which the appliance can be operated safely.
The climate class [Y] and temperature class [Z] define the maximum outline conditions in which the appliances will operate perfectly.
The climate rating is indicated on the type plate.

The minimum room temperature at the place of installation is 16°C.

Recommended temperature setting:

Noise emissions from the appliance
The noise level while the appliance is operating is below 70 dB(A) (relative noise level 1 pW).
The appliance complies with the relevant safety regulations and EU Directives 2014/30/EU and 2006/42/EG.
Disposal notes
The appliance contains reusable materials and should be disposed of properly – not simply with unsorted household refuse.
Appliances that are no longer needed must be disposed of in a professional and appropriate way, in accordance with the current local regulations and laws.
When disposing of the appliance, ensure that the refrigerant circuit is not damaged to prevent the uncontrolled escape of the refrigerant it contains (data on type plate) and oil.
Display in indicating mode
After being commissioned by the team of technicians, the display will be in indicating the mode.
The display shows the current interior temperature.
Important note
The goods must not be inserted until -18°C is shown in the display.
Setup mode
The supplied release key is required to activate setup mode. Activating setup mode
• Touch the activation point on the display with the release key.
An audible warning signal will sound for 1 second.
The operating symbols are displayed.
Note
If no button is pressed for 2 minutes, the electronic control system will automatically switch back to indicating mode.
Setting the real time clock

• Activate setup mode using the release key
• Press and hold the Set button for 5 seconds. Display =
• Press Display =
• Press Set. Display =
• Set the hour by pressing the   buttons.
• Press Set. Display =
• Set the minute by pressing the    buttons.
• Press Set. The new setting will be saved.

The electronic control system will switch back to indicating mode.

• Press and hold the Set button for 5 seconds. Display =
• Press Display =
• Press Display =
• Press Set. Display =
• Set the year by pressing the   buttons.
• Press Set. Display =
• Set the month by pressing the   buttons.
• Press Set. Display =
• Set the day by pressing the  buttons.
• Press Set. The new setting will be saved.

The electronic control system will switch back to indicating mode.

Changing the temperature setting

The desired temperature can be set between -18°C and -23°C.
Depending on the customer’s version, different control areas may be blocked or released.
Proceed as follows:

· Activate setup mode using the release key
The current temperature inside the appliance is displayed.
· Press flashes.
· Press Set  The new setting will be saved.
The electronic control system will switch back to indicating mode.
Note Repeat these steps to reset the temperature to -18°C.
Press the V button instead of the ∧ button.

Activating the defrost function manually

The appliance defrosts automatically.
Increased frost may form on the interior container in high ambient temperature and humidity.
In this case, activate the defrost function manually.
Proceed as follows:

• Activate setup mode using the release key
• Press    flashes.
• Press Set. The defrosting process will be started.

The electronic control system will switch back to indicating the mode. The LED will be lit until the defrosting process is finished. Interior light
(depending on options) Switch the interior light on or off as required.
Switching on the interior light

• Activate setup mode using the release key
• Press  flashes.
• Press Set. The interior light is switched on.

Note Repeat these steps to switch off the interior light again.

Malfunctions

The release key symbol (dot) will flash in the event of a malfunction or if the appliance is defective.
Proceed as follows::
· Activate setup mode using the release key
Either a flashing temperature display or an error code will appear in the display.
Action to take if the temperature display is flashing

• First check whether the appliance doors are closed.
  If the temperature falls after closing the doors, no further action is required. If no drop in temperature is apparent after approx. 10 minutes:

•  Transfer the goods immediately to other appliances.

• Notify the customer service department.

Action to take if an error code is displayed
Error code F1, F2, F4, or F5
The temperature sensor in the appliance is defective.
Action
Notify the customer service department. The goods can be left in the appliance since the temperature is maintained by the appliance being in emergency mode.
Error code Ht
The temperature inside the appliance is too high (warm). Action · Transfer the goods immediately to other appliances. · Notify the customer service department.
Error code nA
A main failure has occurred.
Action

• Press Set →The maximum (warmest) temperature during the mains failure is displayed.
• Decide whether the goods can be used depending on the level of the temperature rise.

Switching the appliance off

• Activate setup mode using the release key
• Press and hold the button for 5 seconds.

The temperature display will go out.
The interior light will go out.
The release key symbol (dot) will still be lit to show that the appliance is connected to the electricity supply.
Important note If the appliance has been switched off using the button, the refrigeration system is switched off but the appliance has not been fully disconnected from the mains. Before cleaning, always disconnect the appliance from the mains. Switch off the fuse.
Switching the appliance on

• Activate setup mode using the release key
• Press the button.

The display will show the current temperature inside the appliance. Repositioning the shelves

|
---|---

Cleaning

The appliance may only be cleaned by authorized, trained personnel.
Clean the appliance at least twice per year.
Do not use steam cleaning equipment to clean the appliance. This may cause damage or injuries.
Do not use acidic, highly alkaline or abrasive cleaning products.
Do not use chemical solvents.
Do not use abrasive cleaning cloths or sponges.
Use a damp cloth only around the electronic display. Ensure that no moisture gets into the electrical components.
Before cleaning, always disconnect the appliance from the mains. Switch off the fuse.
The condenser may only be cleaned by a technician who has been authorized and trained by LIEBHERR.
Inserting the baseplate
Removing the baseplate
Cleaning the glass door
Guideline for correct maintenance of anti-fog film:

• When the surface becomes dirty due to fingerprints, wipe them off with a soft cloth soaked in water (or neutral detergent diluted with water) – do not rub roughly.
• Do not use chemicals or solvents.
• Do not use brushes or abrasives.
• Do not rub with sharp objects (ballpoint pen, scissors, etc.) or hard objects (shoes, bag, etc.).
• Do not spill or spray liquids directly on the film.
• Do not remove the film once applied to the glass door: adhesive properties will vanish once removed.
• Do not use, store or leave the film in hot places or under a direct source of heat, e.g. by the fire, near a heater, etc.

Customer service

If the appliance suffers a malfunction:

• Transfer the stored goods to other appliances.
• Switch off the appliance. See the section entitled Switching the appliance off.
• Disconnect the appliance from the mains > switch off the fuse.
• Notify the customer service department quoting the appliance details.

The appliance details are shown on the service type plate.
The position of the service type plate is shown in the section entitled Description of the appliance.
Shutting down the appliance
If the appliance is shut down for a lengthy period of time:
Switch off the fuse.
Clean the appliance and leave the door open in order to prevent unpleasant smells.
Additional information:
– Food will remain fresh for longer if stored at the correct temperature. This can prevent having to discard food needlessly.
– If the condenser coil is not cleaned every year, it will significantly reduce the appliance’s efficiency.
– The period during which spare parts, necessary for the repair of the refrigerating appliance with a direct sales function, are available is 10 years.
– The minimum duration of the guarantee of the refrigerating appliance with a direct sales function offered by the manufacturer, importer or authorised representative is 2 years.

http://lhg.short-co.de/6rtme
Liebherr Hausgeräte Lienz GmbH
Dr.-Hans-Liebherr-Strasse 1
A-9900 Lienz Österreich
www.liebherr.com
708482202

References

• Liebherr- international Group & family enterprise | Liebherr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>