tp-link TL-SG1005P-PD 5 Port Gigabit Desktop Switch Installation Guide
- June 13, 2024
- tp-link
Table of Contents
tp-link TL-SG1005P-PD 5 Port Gigabit Desktop Switch Installation Guide
TL-SG1005LP 16 Port Gigabit Desktop PoE Switch
Installation Guide
Installation Guide
5/16-Port Gigabit Desktop PoE Switch
TL-SG1005LP 16 Port Gigabit Desktop PoE Switch
LED Explanation
Power
Power| On: Power on
Off: Power off
---|---
PoE MAX
PoE Max| TL-SG1005LP
On: 33 W ≤ Total power supply < 40 W
Flashing: Total power supply ≥ 40 W
Off: Total power supply < 33 W
TL-SG1005P
On: 58 W ≤ Total power supply < 65 W
Flashing: Total power supply ≥ 65 W
Off: Total power supply < 58W
TL-SG116P
On: Total power supply ≥ 113 W
Flashing: Total power supply ≥ 113 W and lasts for more than 2 minutes
Off: Total power supply < 113W
---|---
Link/Act and PoE Status
Switches Explanation
Note: The numbers in brackets indicate the ports where the feature takes
effect. For example, when Extend(1-4) is toggled to On, the Extend mode will
be enabled for ports 1-4.
Priority (for TL-SG116P)
Off: All the ports transmit data with the same priority.
On: The corresponding ports transmit data with a higher priority than other
ports. When congestion occurs, packets which are transmitted by the ports with
a higher priority occupy the whole bandwidth.
Extend (for TL-SG1005P/TL-SG116P)
Off: The corresponding ports run at 10/100/1000 Mbps and support PoE power
supply up to 100 m away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to
250 m away.
Note: For simplicity, we will take TL-SG1005P for example throughout
this Guide.
Isolation (for TL-SG116P)
Off: Ports can transmit data with each other.
On: The corresponding ports cannot transmit data with other downlink ports.
They can transmit data only with the uplink ports (ports 15-16 of TL-SG116P).
Recovery (for TL-SG1005P/TL-SG116P)
Off: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered
device (PD). When the switch finds that the PD works abnormally, the switch
will reboot it.
Connection
Note:
-
1. PoE ports can also connect to non-PoE devices, but only transmit data. -
TL-SG1005LP can supply up to 30 W for each PoE port and 40 W for all PoE ports.
-
TL-SG1005P can supply up to 30 W for each PoE port and 65 W for all PoE ports.
-
TL-SG116P can supply up to 30 W for each PoE port and 120 W for all PoE ports.
Specifications
General Specifications
Standard| IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af,
IEEE802.3at, IEEE802.1p
---|---
Protocol| CSMA/CD
Interface| For TL-SG1005LP/TL-SG1005P: 5 10/100/1000 Mbps RJ45 Ports Auto-
Negotiation MDI/MDIX
PoE Ports: Port 1-Port 4
For TL-SG116P: 16 10/100/1000 Mbps RJ45 Ports Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-Port 16
Total Power Supply: 40 W (TL-SG1005LP)/65 W (TL-SG1005P)/120 W (TL-SG116P)
Network Media (Cable)| 10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m); EIA/TIA-568 100Ω STP
(maximum 100 m)
1000BASE-T: UTP category 5e cable or above (maximum 100 m); EIA/TIA-568 100Ω
STP (maximum 100 m)
Switching Capacity| 10 Gbps (TL-SG1005LP/TL-SG1005P)/32 Gbps (TL-SG116P)
MAC Address Table| 2 K (TL-SG1005LP/TL-SG1005P)/8 K (TL-SG116P)
Transfer Method| Store-and-Forward
MAC Address Learning| Automatically learning, automatically aging
Power Supply| External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output:
53.5 VDC /0.81 A (TL-SG1005LP)
53.5 VDC /1.31 A (TL-SG1005P)
53.5 VDC /2.43 A (TL-SG116P)
Wall Mountable| Yes
Distance Between
Mounting Holes| 39 mm (TL-SG1005LP/TL-SG1005P)/200 mm (TL-SG116P)
Environmental and Physical Specifications Operating Temperature| 0 ˚C to
40 ˚C (32 ˚F to 104 ˚F)
---|---
Storage Temperature| -40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)
Operating Humidity| 10% to 90%RH non-condensing
Storage Humidity| 5% to 90%RH non-condensing
Frequently Asked Questions (FAQ)
Q1. Why is the Power LED not lit?****
– The Power LED should be lit when the power system is working normally. If
the Power LED is not lit, please try the following:
– A1: Make sure the AC power cord is connected to the switch with power
source properly.
– A2: Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
– A3: Make sure the power source is on.
Q2. Why is the Link/Act LED not lit while a device is connected to the corresponding port?****
– It is recommended that you check the following items:
– A1: Make sure that the cable connectors are firmly plugged into the
switch and the device.
– A2: Make sure the connected device is turned on and works normally.
– A3: The cable must be less than 100 meters long (328 feet). If Extend
Mode is enabled, it should be less than 250 meters (820 feet).
Q3. Why are PoE ports not supplying power for PoE devices?****
– When the total power consumption of connected PoE devices exceeds the
maximum, the PoE port with a smaller port number has higher priority. The
system will cut off power to the ports with larger port numbers to ensure
supplying to other ports.
– Take TL-SG1005P as an example. If port 1, 2 and 4 are consuming 15.4 W
respectively, and an additional PoE device with 19 W is connected to port 3,
the system will cut off the power of port 4 to compensate for the overload.
Q4. What should I notice before using the PoE Auto Recovery feature?****
– A1: Before upgrading a connected PoE powered device (PD), disable PoE
Auto Recovery to avoid the PD’s damage.
– A2: When a PD does not send data packets to the switch for a long
period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto
Recovery to avoid the PD repeatedly rebooting.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link Community.
For technical support and other information, please visit https://www.tp-
link.com/support, or simply scan the QR code.
http://www.tp-link.com/support
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/support/ce/
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016.
The original UK declaration of conformity may be found at https://www.tp-
link.com/support/ukca
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Place the device with its bottom surface downward.
- Do not use damaged charger or USB cable to charge the device.
- Do not use any other chargers than those recommended.
- Adapter shall be installed near the equipment and shall be easily accessible.
- The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
-
-
FCC compliance information statement
Product Name: 5/16-Port Gigabit Desktop PoE Switch
Model Number: TL-SG1005LP/TL-SG1005P/TL-SG116P Component Name| Model
---|---
I.T.E. Power Supply| T535081-2-DT (For TL-SG1005LP)
T535131-2-DT (For TL-SG1005P)
T535243-2-DT (For TL-SG116P)
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: [email protected]
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1)This device may not cause harmful interference.
2)This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above
has been shown to comply with the applicable technical standards, FCC part 15.
There is no unauthorized change is made in the equipment and the equipment is
properly maintained and operated.
Issue Date: 2023/03/09
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the
product.
Read More About This Manual & Download PDF
References
- TP-Link Community
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link