Apone APP-P4S4U Smart Power Strip User Guide
- June 13, 2024
- APONE
Table of Contents
Smart Power Strip
Quick Guide
APP-P4S4U Smart Power Strip
Model: APP-P4S4U
Length: 18 m
tem Dimensions: 29.5
x 5.8 x3 (cm)
Please read the operating instructions before use.
Product Overview
Apone Smart Power Sirip has 4 power outets and 4 USB outputs. This product
works seamlessly with your home ‘automation devices trough the Apone Smart app
or voice:
commands with Amazon Alexa or Google Assistant.
it provides wireless control of your power ffom anywhere.
It ‘automatically switches individual devices on and off based on muliple
timers. Itelligent USB charging ports can detect your devices and deliver the
ideal charging for optimum safety.
NOTE: The product only supports 2.4GHz WI-Fi network, It oes not support 5GHz
Wi-Fi network.
Technical Specification
Rated Current: 154 (Max) / Rated Power: 1875W.
Rated Voltage: AC100V-240V (50/60Hz)
Surge protection: 800
4 XUSB Output: 5V, 3.1A (Max)
Easy Installation
Scan the QR code of install Apone Smart 2pp from App Store or Google Play.
-
Register
If you don’t have Apone Smart app account, you can register one. Please read the description of the regisration process.
Click Register, enter the Privacy Policy page, click Agree.
and enter your e-mail address. The system aomaticaly seects yourcuren Courteyl Region, or you an Cauniy Region
Eneryour rogistaton code from your e-mal
Setpassword (510 20 craracer incluingaters and dats)
-
Log in with an existing account
I you already have Apone Smart app account, skip registration and click Log in with existing account o enter the log n page.
(1) The system automatically selects your current Country/ Region, or you can manually choose your Country/ Region.
(2) Enter your email address and your password to g ito the system.
Add Device to Apone Smart APP
STEP1: Pl the Smart Povier Stipirto the wal oute.
STEP 2. Open Apone Smart app, click + on the upper right comer of the screen.
Select Power Strip (Wi-Fil STEP 3 Enter Wi-Fi Password (Wireless Type:
2.4GHz)
Make sure the Power Strip LED lightis binking. Ifthe red gt does not ik, reset
the device by pressing the ON/ (OFF button n seconds urtl e red gt binks.),
STEP 4: Please select ither AP Mods or EZ Mode to pairyour device.
- 2 Mode-red LED light btink rapidly
AddngDevice..
added successfully
Connect your mobile phone to the hotspot Apone Smart-
XXXX.
(2) AP Mode-red LED light to blink slowly.
Light Indicators
Red Light Blinking: Syne mode
Red Light Steady On:
Successfully paired to wireless network
Red Light Off: Not connected to wireless network
Blue Light On: Power connected to output ports.
Blue Light Off: Power disconnected to output ports
NOTE : This device support 2.4GHz Wi-Fi Network only. Itis compatible
with both Android version 5.0 and above as well as i0S 8 and above. DO NOT
overload capacity. For more troubleshooting help, please visit:
www.apone.ca.
Orsend us an e-mail at info@apone.ca.
FCC ID Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
“Please note that changes or modifications of this product is not expressly
approved by the party resposible for compliance could avoid the user’s
anthority to operate the equipment.”
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in aparticular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The distance between user and products should be no less than 20cm
IC Statement
- This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device. The device is compliance with RF field strength limits, users can obtain Canadian information on RF exposure and compliance. This Class B digital apparatus complies with Canadian ICES-003. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.