Parrot Uncle A531101CC 16.5 Inch Black LED Indoor Flush Mount Fandelier Ceiling Fan Instruction Manual
- June 13, 2024
- Parrot Uncle
Table of Contents
A531101CC
Installation & Operating Instructions for the
Parrotuncle Owner’s Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Sicherheit information
- To reduce the risk of an electrical blow, electricity on the protective switch or the safety box went out before starting.
- All wiring must correspond to the NASI/NFPA 70-1999 National Electric Code and local electrical regulations. The electrical installation must be carried out by a qualified and approved electrician.
- The connection box and support construction must be assembled safely and 35 pounds (15.9 kilos) must be able to transport reliably. Use only output boxes listed with labeling “Accepted for fans with a weight of £ 35 (15.9 kilos) or less.”
- The fan must be installed with a minimum distance of 2.1 m (7 feet) from the posterior edge of the wings to the floor.
- Do not operate the reverse switch if the fan wings are moving. You have to turn off the fan and stop the wings before reverse the direction of the wing.
- Do not place objects on the road to wings.
- To avoid lesions or damage to the fan and other objects, be careful if you work on the fan or clean it.
- Electrical diagrams only serve as a reference. The lighting rates that are not delivered with the fan must be listed and marked with the valve model that will be installed for use. The switches must be general use switches UL. Take into account the instructions for the appropriate installation included in the lighting rates and the switches.
- After the electrical connections have been made, the size staircase must be turned up and carefully push to the plug box. The cables must be distributed in such a way that the ground connected driver and the device head are next to the socket.
- All fixing screws must be verified before installation and, if necessary, followed.
- Do NOT install this fan with variable speed wall control or wall-mounted dimmer switch. It will permanently damage the fan’s transmitter and cause the fan’s function to fail.
WARNING: To reduce the risk of injury, knife supports (also known as
flanges) cannot be folded during installation or after installation. Do not
put any object on the path of wings.
WARNING: Remove rubber motor attacks at the bottom of the fan before
mounting the wings or try the engine.
WARNING: To avoid the risk of a fire or an electrical blow, this fan
should not be used with a semiconductor speed controller.
WARNING: To avoid a possible electric shock, turn off the current in the
main security box before wiring. If you feel that you do not have enough
knowledge or experience in electrical wiring, communicate with a license
electrician.
WARNING: Electrical diagrams only serve as a reference. The optional use
of an lighting rate must be on the list and marked with this fan for use.
WARNING: To reduce the risk of fires, electrical discharges or injuries,
assemble the device in a socket that with the inscription accepted for fans
with a weight of £ 35) or less. It is marked and use the screws supplied with
the plug.
TECHNICAL INFORMATION
| SKU | Nominal voltage | Nominal output (motor) | light |
|---|---|---|---|
| A531101CC | 120V AC | 30W | 1*10W LED (Included) |
NOTE: Please remove the outer frame first for
ease of installation.
Pls check whether above
accessories are completed or not?Yes,and install.
- Use the Mounting Plate as a guide drill 4 holes for Anchor and insert the Anchor. Install the mounting plate onto Outlet Box with Box Screws and Tapping Screws.
- Hook the fan to the supporting cable with keylink and lock the keylink.
- Connect the wire connector plugs correctly. The wire connector plugs design with fool proof device, please don’t force to plug. Otherwise it may affect the normal use of the light fan or burn the fan motor.
- Place Controller into the canopy and tidy up the wiring. Push the canopyto the mounting plate, make two sliding holes aligned to the two preinstalled screws, and then turn clockwise until tight. Tighten the pre installed screws. Fix the canopy with two other screws.
TRANSMITTER
Insert battery into transmitter,
turn on the power supply to fan and it is ready to use.
| Fan speed 1 – 6 control (1-low speed, 6-high speed)
---|---
| Turns off the fan
| Timing the fan
| Auto off after 1 hr
| Auto off after 3 hr
| Auto off after 6 hr
| Cancel timing setup
| Forward or reverse operation:
change fan rotating direction.
| Natural Wind: Fan speed changes within its range creating gentle natural
wind effect.
| Lamp on-off control
TRANSMITTER HOLDER Install the transmitter holder to the wall or any flat
surface with the two mounting screw provided.
FORWARD/REVERSE FUNCTION
Forward
Fan rotates anti-clockwise creating a downward airflow delivering a cooling
effect.
Used during hot weather for cooling air.
Reverse
Fan rotates clockwise creating an upward airflow of warm air moving from the
ceiling. This function best at lower fan speeds.
Better during cold weather to circulate air.
Size of product
AFTER INSTALLATION
TRANSMITTER IS NOT WORKING
- Ensure the transmitter is within the 20 foot range of the fan.
- Check batteries to insure they are good and oriented correctly. The indicator should light up when the button is pressed.
NOISY
When it is quiet(especially at night) you may hear occasional small noises.
This is normal. Please allow a 24-hour “breaking-in” period, most noises
associated with a new fan disappear during the time.
WOBBLE
The fan blades have been adjusted in the factory to minimize any wobble.
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT
THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS IS
QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM.
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE
MOUNTING BRACKET AND DOWNROD ARE SECURE.
CARE AND CLEANING
- To ensure a proper and safety usage, inspect the suspension system and tighten all connections every 6 months.
- Periodic cleaning of your ceiling fan. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan.
- Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
- The bulbs and near by parts will be still hot after the power is shut off. To avoid burn, please clean them after they are cooled down.
- Motor has permanently lubricated ball bearing. No need to oil.
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>