ZIMHOME ZT2220 2.4G Wireless Microphone Transmitter Instruction Manual

ZIMHOME ZT2220 2.4G Wireless Microphone Transmitter

Product Information

The AM-W10 is a 2.4G wireless microphone. It is designed to comply with Part 15 of the FCC Rules, ensuring that it operates within the allowed limits for radio frequency (RF) devices. The device has been evaluated to meet general RF exposure requirements, allowing it to be used in portable exposure conditions without any restrictions.

Product Usage Instructions

1. Ensure that the AM-W10 wireless microphone is fully charged or has fresh batteries installed.
2. Power on the wireless microphone by pressing the power button located on the device.
3. Turn on the receiver or audio device that the wireless microphone will be connected to.
4. Pair the wireless microphone with the receiver by following the pairing instructions provided in the receiver’s user manual.
5. Once paired, adjust the volume levels on both the wireless microphone and the receiver to achieve the desired audio level.
6. Position the wireless microphone close to the sound source for optimal audio capture.
7. Use the wireless microphone as needed for speeches, presentations, performances, or any other application requiring wireless audio transmission.
8. After use, power off the wireless microphone to conserve battery life.
9. If any interference or undesired operation occurs duringusage, try adjusting the position of the wireless microphone or consult the troubleshooting section of the user manual for further assistance.

PACKAGE LIST

TX1 & TX2

Indicator Function

status| Power lndlcator(red)| Power lndlcator(blue)| Connect lndlcator(red)| Connect lndlcator(blue)
---|---|---|---|---
Flash slowly| Low power| I| I| Not connected
Quick flash 3

times, then ofl’

| Lacking power and automatically turned ofl’| I| I| I
Keep on and light| Charging(on)| Full Charge(off)| Mic Mute| Complete connection

Button Function

1. ON/OFF
   Press for 3 seconds ON/OFF the Transmitter.

2. MICROPHONE MUTE FUNCTION
   In the power on state, short press the power button to realize the microphone MUTE/ RECEPTION function.

RX

Button Function

1. ON/OFF
   Press for 3 seconds ON/OFF the Receiver

2. NORMAL /POWER SAVE MODE SWITCHING
   In the power-on state, short press the power button once to enter the mode- switching function, and the mode indication signal flashes. At the same time, short press the Vol + button to realize the NORMAL/ POWER SAVE MODE SWITCHING, After completing the adjustment, stand for 5 seconds to exit the channel switching function.

3. MONO/ STEREO CHANNEL SWITCHING
   In the power-on state, short press the power button twice to enter the channel switching function, and the output level flashes. At the same time, short press the Vol+ button to realize MONO/ STEREO CHANNEL SWITCHING, After completing the adjustment, stand for 5 seconds to exit the channel-switching function.

TX1 & TX2

RX

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
  The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>