AOMWAY TX004 5.8GHz Transmitter and Receiver User Manual
- June 13, 2024
- AOMWAY
Table of Contents
AOMWAY 5.8GHz
Transmitter & Receiver
User Manual
TX004 5.8GHz Transmitter and Receiver
Transmitter Specifications:
| Model# | TX004 | TX003 | TX1000 |
|---|---|---|---|
| Output Power | 25/200mw | 25/100/200/600mw | 1000mw |
| Working Voltage | 6-26v | 6-26v | 7-26v |
| Power Consumption | 12v170mA@200mw | 12v170mA@200mw | 12V 650mA |
| Frequencies | 64CH: | 64CH | 32CH |
| Format | NTSC/PAL | NTSC/PAL | NTSC/PAL |
| Output Voltage | 5V | 5V | 5V/12V |
| Antenna Connector | IPEX | MMCX | SMA-Jack (outer thread, inner hole) |
| Weight | 3g | 7.3g | 42g (with outer case) |
Frequency Chart:
Output Voltage:
There are two output voltage choices to power 5V or 12V camera.
Select via a jumper to power 12V or 5V camera.
a) Jumper onto LEFT socket for 5V output voltage.
b) Jumper onto RIGHT socket for 12V output voltage.
(same as the input voltage of receiver) Tx Accessories
| TX Power | TX004 | TX003 | 1000mw (V4) |
|---|---|---|---|
| Antenna X1 | 3db omni antenna | 3db omni antenna | 5db omni antenna |
| DC cable X1 | JST 1.0*6P | JST 1.0*6P | DuPont Header Locking Socket/JST |
| AV cable X1 | – | – | DuPont Header Locking Socket /Bare Tin |
Cable Connection Diagram
Receiver Specifications:
| Model | DIV006 V4(DVR) |
|---|---|
| DVR Function | DVR with auto save function |
| Working Voltage | 7-26v |
| Power Consumption | 12V,210mA |
| Channel | 64CH ( RaceBand ) |
| Format | NTSC/PAL selectable via menu |
| Sensitivity | -95db |
| Channel Selection | Digital Display, Single Button Selection, Auto Scan, |
Diversity
Antenna Connector| SMA- Jack (outer thread, inner hole)
DIV006 Features:
- DVR recording audio and video signal simultaneously in D1 resolution.
- AV out: 640×480
- Video compression format: MJPG
- TF card slot, support to 64GB
- Recording file format: AVI
- Playback available
- PAL/NTSC selectable via menu.
- 48CH selection by single button, digital display current channel#.
- Single short press button to change channel from CH1 to 8 and buzzer beeps while each press; long beep indicates on CH1.
- Each time long press 3s to change band from A to H.
- Digital tube point indicates which antenna is selected to work.
Frequency Chart:
DVR Operation
- DIV006 receiver’s DVR has auto save file function. Each time after power off, need to wait 10s before re-plug on power, otherwise DVR will not be ready to use.
- When power on, DVR will ouput AOMWAY logo on screen, and then display RF/AV signal; DVR is standing by at this moment and LED light stays solid on.
- Short press down DVR switch to start recording, LED light will be flashing; short press down again to stop recording, LED light changes to be solid on.
- Playback function:
Long press DVR switch for 5s to enter main menu:
A: ‘Up’ and ‘Down’ to select options on main menu:
- Play back recorded file
- Format TF card
- Language selection
- Auto start recording when power on
- Overwrite recording when card is full
- Selection of output format (PAL/NTSC)
B: Short press down to enter sub-menu:
- ‘Up’ and ‘Down’ to select file, short press down to play back
- During playback, ‘Up’ to switch fast forward speed at 1X,2X,4X,8X; ‘Down’ to switch fast backward speed at 1X,2X,4X,8X.
- During playback, short press down DVR switch to display file or pause.
C: During playback, long press down 5s to return to main menu
D: Short press down to return to standby mode
- AV1 passes signal to DVR first, and then output; this is in order to prevent blue screen and enable user to check actual recording status.
- AV2 can output signal directly to AAT or monitor, etc.
- Two AV ports can work simultaneously.
Receiver Accessories
- 2x 5.8GHz antenna
- 1x 1.2m, 3.5male/RCA male AV cable
- 1x 1m, 2.1*5.5male/bare tin power cable
- 1x 30cm, 3.5male/RCA female AV cable
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>