VYRVE AUDIO MIZAR Active PA Speaker Set Bluetooth User Manual
- October 31, 2023
- VYRVE AUDIO
Table of Contents
VYRVE AUDIO MIZAR Active PA Speaker Set Bluetooth
Introduction
Thank you very much for choosing the MIZAR compact PA system from Vyrve!
Please carefully read this manual and the safety instructions before you use
the unit in order to fully understand its functions and to obtain the best
results.
Keep this manual in a safe place for reference.
Features
This 1.1 / 2.1 sound system is using a compact high-power Class-D amplifier with a low consumption switching power supply with little heat waste. This versatile system can be used on many occasions – at parties, small concerts, band performances, in rehearsal rooms, for presentations etc.
- Simple and quick installation.
- Satellite speakers are contained in the back of the subwoofer, the system is very portable.
- Can be set up in various configurations.
- The multi-function mixer accepts a variety of different sound sources.
- The built-in Bluetooth® receiver allows streaming music from a smartphone.
- Mixer and power amplifier are built into the subwoofer.
- The system can be configured as a 1.1 or 2.1 sound system according to the actual requirement.
SAFETY INSTRUCTIONS
INSTRUCTIONS FOR THE PREVENTION OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS
About WARNING and CAUTION notices
- Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
- Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
ALWAYS OBSERVE THE FOLLOWING
- Before using this unit, make sure to read the instructions below, and the owner’s manual.
- Do not open (or modify in any way) the unit.
- Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to an authorized service center.
- Never use or store the unit in places that are:
- subject to temperature extremes(e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are
- damp and humid (e.g., baths, washrooms, on wet floors); or are
- exposed to rain; or are
- dusty; or are
- subject to high levels of vibration.
- Make sure you always have the unit placed so it is level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces.
- Make sure the position of the voltage selector switch on the rear of the unit matches the voltage supply in your country. By default the voltage rating is set to “230V” (220~240V). A wrong voltage selection can destroy the unit.
- Use only the attached power cord. Also, the supplied power cord must not be used with any other device.
- Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged power cords are fire and shock hazards.
- This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist.
- Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.
- Immediately turn the power off, remove the power cord from the outlet, and request servicing by your retailer or the an authorized Service Center when:
- the power cord or the plug has been damaged; or
- if smoke or unusual odor occurs; or
- objects have fallen into, or liquid has been spilled onto the unit; or
- the unit has been exposed to rain (or otherwise has become wet); or
- the unit does not appear to operate normally or exhibits a marked change in performance.
- Protect the unit from strong impact. (Do not drop it!)
- Do not force the unit to share a power outlet with an unreasonable number of other devices. Be especially careful when using extension cord – the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the power cord to heat up and eventually melt through.
- Do not remove and replace the speaker grill and speaker by any means. Shock hazardous voltages and currents are present inside the enclosure.
- The unit is only powered off completely when you switch it off and unplug it from the mains outlet.
- Always grasp only the plug of the power cord when plugging into, or unplugging from, an outlet or this unit.
- Never handle the power cord or its plug with wet hands when plugging into, or unplugging from, an outlet or this unit.
- At regular intervals, you should unplug the power cord and clean it by using a dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire.
CAUTION
- Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children.
- Never climb on top of, nor place heavy objects on the unit. Do not place drinks on top of the unit.
- The unit should be located so its location or position does not interfere with their proper ventilation.
- Before moving the unit, disconnect the power cord and all cables coming from external devices.
- Before cleaning the unit, turn off the power and unplug the power cord from the outlet.
- Whenever you suspect the possibility of lightning in your area, disconnect the power cord from the outlet.
- Should you remove screws, keep them in a safe place out of children’s reach, so there is no chance of them being swallowed accidentally.
- Before using the unit in a foreign country, check the local line voltage and – if necessary – change the position of the voltage selector accordingly.
- When setting up the speaker stands be careful not to pinch your fingers while spreading the stand legs. Always store the speaker stands out of the reach of children.
Make sure that the speaker stands are placed on a solid and level surface and cannot fall over. Always run the speaker cables in a thoughtful way so that no one can stumble over them.
Use the speaker stands exclusively for the included satellite speakers. The speaker stands are not designed for other speakers.
IMPORTANT NOTES
-
Power Supply
Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise filter between this unit and the electrical outlet. -
Placement
Using the unit near power amplifier (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference. -
This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.
-
Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
-
Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Also, do not allow lighting devices that normally are used while their light source is very close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time. Excessive heat can deform or discolor the unit.
-
When moved from one location to another where the temperature and /or humidity is very different, water droplets (condensation) may form inside the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
Maintenance
- Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or otherwise harmfully affect the finish.
- Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior finish.
- For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
- Never use benzene, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
Additional Precautions
- Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
- When connecting/disconnecting all cables, grasp the connector itself-never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements.
- To avoid disturbing your neighbors, try to keep the unit’s volume at reasonable levels (especially when it is late at night or near specific places like schools or hospitals).
- When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.
- Never defeat the earth ground connection of the unit by covering or disconnecting the protective conductor (e.g. in case of a ground hum) of the mains plug. The earth ground connection is provided for your safety.
WHAT’S IN THE BOX
OPERATION MODES AND SETUP
MONO MODE
Slide the SETUP switch to the right to select the 1.1 mode (mono).
In this mode the satellites are fed only by the left output of the subwoofer,
the right output is disabled. THERE ARE TWO POSSIBLE SETUP CONFIGURATIONS:
COMPACT AND STANDARD
Connection
PANEL CONTROLS
CONTROLS, SWITCHES, AND CONNECTORS
PANEL CONTROL DESCRIPTION
-
SETUP SWITCH
This switch allows you to select the operation mode (stereo or mono)
1.1 Mono mode: Slide the SETUP switch into the right position. Now only the left output of the subwoofer (SPEAKER OUT L) is active.
2.1 Stereo mode: Slide the SETUP switch into the left position. Now both subwoofer outputs (L and R) are active. CH1 to CH4 inputs are mono and are equally sent to the left and right outputs, thus panned to the center. Inputs CH5/6 and CH7/8 are stereo; CH5 and CH7 signals are panned hard left, and CH6 and CH8 signals are panned hard right. -
CH1-CH4 COMBO INPUTS
Here you can either connect a microphone (XLR) or a line-level source (1/4” TRS). -
CH1-CH4 LEVEL CONTROL
These controls are used to set the levels for the inputs CH1 to CH4. -
CH1-CH4 MIC/LINE SELECT SWITCH
These switches are used to select which input signal of the combo jack is being sent to its respective channel; MIC = XLR, LINE = ¼” TRS -
CH1-CH4 TONE CONTROL
Turn this control clockwise to gradually boost both the low and high frequencies of the signal (“Loudness effect”). Turn the control fully counterclockwise (MIN) if you do not want to affect the input signal. -
CH5/6 INPUT
The stereo channel CH5/6 can either be fed by its 1/4″ TRS jacks or the RCA jacks. -
CH5/6 LEVEL CONTROL
This control sets the level of the stereo channel CH5/6. -
CH7/8 AUX/ BLUETOOTH® INPUT
The AUX stereo channel can either be fed by its 3.5mm TRS stereo jack or wireless from an external Bluetooth® device. Select the desired source with the AUX switch (11). -
PAIR BUTTON
This button is used to establish a wireless connection to a Bluetooth® device, e.g. your phone. Make sure that the AUX switch (11) has been set to the left position ( ) before you press the PAIR button. After you have pressed the PAIR button, the LED (10) will flash. Switch your phone (or other device) into Bluetooth® search mode. Select “Mizar” from the search results. The LED (10) will now be lit solid in blue, the Bluetooth® pairing was successful and you can start streaming from your device. If you don’t need Bluetooth® any more press the PAIR button again, the LED (10) goes out. -
BLUETOOTH® LED
a) LED out: no Bluetooth® connection
b) LED lit solid: external device is properly paired to this unit.
c) LED is flashing: pairing in progress -
CH7/8 AUX SWITCH
This switch allows you to choose the input source for channel CH7/8, left position = Bluetooth® ( ), right = 3.5mm TRS stereo jack. -
DELAY CONTROL
Use this control to set the delay time of the Echo effect. Turn the control clockwise to increase the delay time. -
ECHO CONTROL
Use this control to set the volume of the Echo effect. Turn the control fully anticlockwise (MIN) to turn off the Echo effect. -
SUB CONTROL
Use this control to set the volume of the subwoofer. We recommend to set the control to the middle (12:00) to start with. -
MASTER CONTROL
Use this control to set the overall volume of the PA system. -
PWR/LIMIT LED
This dual-color led indicates the power status and signal peaks.
BLUE = The unit is switched on and operational.
RED = Indicates short-term signal peaks
If the LED is constantly lit, the signal is overdriving the unit. In this case please reduce the individual levels of the input channels. -
MONITOR OUT
Use these jacks to feed the mains signal of the MIZAR to an external mixer, additional active speakers or a PA system. -
SPEAKER LED
This dual-color led indicates the status of the speaker outputs.
GREEN = active speaker output
RED = disabled speaker output -
L/R SPEAKER OUT
This is where you connect the MIZAR satellite speakers. Please use the included speaker cables. -
POWER SWITCH
Turns the unit on or off. -
FUSE
This is the mains AC safety fuse, the specification is T3.15 AL/250V.
WARNING: If you need to replace the fuse, only use a fuse of the exact same type and rating. Disconnect the unit from mains before replacing the fuse. If you change the voltage selector to 115 V, you have to change the mains fuse too (T6.3 AL/250V). -
AC POWER INPUT
Plug in the supplied power cord here.
WARNING: Please only use the supplied original power cord. The power cord should be unplugged from the AC outlet whenever the unit is to remain unused for an extended period of time. -
VOLTAGE SELECTOR
Use this switch to select the voltage rating according to the AC supply in your country. The default setting is “230V” (220~240V).
SPECIFICATIONS
| MODEL | MIZAR |
|---|---|
| TYPE | ACTIVE SUBWOOFER |
SPEAKER
| ****
1x 10”
| Midrange:1x 4.75” Tweeter: 1x 1” driver
QUANTITY| 1| 2
INPUT
| 4x Combo (XLR/1/4” TRS, balanced)
2x RCA (L/R)
1x AUX (3.5mm TRS stereo/Bluetooth®)
OUTPUT| 2x 6.35mm TS, unbalanced
POWER CONNECTION| IEC
POWER VOLTAGE| 220~240VAC – 50/60Hz
POWER
| ****
250W RMS
| 1.1 Mode: 60W RMS
2.1 Mode: 120W RMS
TOTAL POWER| 370W RMS
FUSE| T 3.15 AL/250V 5×20 mm (220~240V) / T 6.3 AL/250V 5×20 mm (100~120
V)
LIMITER| Soft Limiter
FREQUENCY RANGE| 50Hz – 160Hz| 155Hz – 20kHz
SYSTEM FREQUENCY| 50Hz – 20kHz, ±3 dB
MAX SPL| 123dB| 1.1 Modus: 125dB
2.1 Modus: 130dB
CABINET| ABS Plastic| ABS Plastic
DIMENSIONS
（ H x W x D ）
| ****
458 x 350 x 407mm
| ****
227 x 140 x 155mm
COLOR| black| black
WEIGHT| 14kg| 1.9kg
Hyperactive Audiotechnik GmbH
Neukirchner Str. 18
D-65510 Hünstetten
Deutschland / Germany
www.hyperactive.de