elica EPR634SS Palermo 34″ Stainless Steel Range Hood Insert Installation Guide
- June 4, 2024
- ELICA
Table of Contents
elica EPR634SS Palermo 34″ Stainless Steel Range Hood Insert Installation
Guide
PRELIMINARY INSTRUCTIONS
WARNING
When building a custom hood for an insert or power pack, always follow all
applicable construction codes and standards. See the table and illustration
below to locate your liner and use corresponding custom hood base dimensions.
For the liner installation, only the bottom of the custom hood is needed. Do
not finalize the entire custom hood yet, because an access is needed for the
insert or power pack electrical connection.
NOTE: We recommend the base of the custom hood should be 3 ⁄4’’ inch thick plywood. We recommend the sides, front and backboard (if included) of the custom hood to be 3⁄4’’ thick, assuming standard cabinet widths. The INSIDE DEPTH shown in the table above assumes a minimum cabinet backboard thickness of 3 ⁄8’’.
Consider the shape and size of the power pack to determine the configuration
of the custom hood. For more details, refer to the installation manual of the
power pack.
For custom hood liner detailed installation instructions, see the reverse of
this page.
Liner Models
| Power Pack models| Inside width – A|
Inside Depth – B
---|---|---|---
| | | Whithout Backboard| Whith Backboard
KIT02773| EAS428SS EPR628SS| 28 ²⁹/₃₂ (73.74 cm)| 181 ⁄4” (46.4cm) to 212 ⁄8”
(53.9cm)| 171 ⁄2” (44.5cm) to 201 ⁄2” (52cm)
KIT02774| EAS428SS EPR628SS| 34 1/2” (87.6 cm)| 186 ⁄16” (46.8cm) to 212 ⁄8
(54.3cm)| 1710⁄16” (44.9cm) to 2010⁄16” (52.4cm)
CAUTION: Before installing, remove the protective plastic film from all parts.
NOTE: The custom hood liner must be installed before the insert or power pack unit.
CAUTION: FOR ELECTRIC RANGES INSTALLATION: MOUNT THE HOOD SO THAT THE BOTTOM EDGE OF THE HOOD LINER IS NOT LESS THAN 24” (60.9 CM) ABOVE THE COOKING SURFACE (height measured from the cooktop to the lowest part of the Liner).
FOR GAS RANGES INSTALLATION: MOUNT THE HOOD SO THAT THE BOTTOM EDGE OF THE HOOD LINER IS NOT LESS THAN 30” (76,2 CM) ABOVE THE COOKING SURFACE (height measured from the cooktop to the lowest part of the Liner).
-
Using the screws provided, temporarily install the main liner plate A to the external base of the cabinet B. Fig. 1.
NOTE: Main liner plate should be positioned in custom hood as far rearward as possible. -
Using a pencil, mark the outline of the future hole for the power pack. Fig. 2.
-
Remove the main liner plate from the custom hood.
-
Cut the hole in the bottom of the cabinet. Fig. 3.
-
Reinstall the main liner plate to the base of the cabinet and secure it with 4 screws. Fig. 4.
-
Slide the front panel section C forward into the nose of the cabinet base. Take care not to scratch main liner plate when installing front panel section of liner. Assemble it to the frontal side of the cabinet, using one screw per screw hole. Fig. 5.
-
Install the two power pack’s mounting brackets D. First, to the bottom face of the cabinet (a).
NOTE: Guided by the pilot holes in the liner kit. Then, with the help of two or more persons, get the power pack hood into the cabinet through the hole and then secure it to the mounting bracket with the provided screws (b). Fig. 6.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>