LATICRETE 315-1 Tile Adhesive User Guide

LATICRETE 315-1 Tile Adhesive

ADVANTAGES

• High tack – Will hang tile without slippage
• Dual purpose, for walls and floors
• Ready to use, just mix with water except for exterior facades.
• Long open time.
• Water & heat resistant.
• Strong bond and durable.

MANUFACTURER

LATICRETE Middle East LLC.

P.O. Box. 86028, Ras Al Khaimah
United Arab Emirates
Toll Free (within UAE) 800 5632
Telephone: + 971 7 244 6396
Fax: + 971 7 244 5915
Internet: www.laticrete.me

USES

Designed for interior or exterior installation of ceramic tile and natural stone for walls and floors.
For exterior façade, Mix with latex : LATICRETE® 282 Grout and Mortar Fortifier / 3701 Mortar Admix.

Must fortify with latex for impervious tiles, porcelain, mosaic, glass, and stone tiles, use with cement backer board and heavy traffic areas.

STANDARDS / CERTIFICATIONS

Applicable Standards:

• C1TE: Conforms to EN12004
• Meets ANSI A 118.1 when mixed with water.
• Meets ANSI A 118.4 & BS5980, Class AA when mixed with Latex.

Product Conformity Certification.

This product has been certified for Low Emitting Materials by Dubai Central Laboratory Department (DCLD) of Dubai Municipality.
No.CL20020733: 2017 Al Safat Dubai Green Building Evaluation System.

Packaging – 20kg bag; 72 bags per pallet
Color: Grey and White

Suitable Substrates

• Concrete
• Cement plaster
• Concrete masonry
• Cement mortar bed
• Cement terrazzo
• Brick Masonary
• Cement backer board***
• Ceramic Tiles & Stones

*** Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use.

Approximate Coverage

20 Kg bag will cover approximately 5 to 6 m² using 6 x 6 mm square notch trowel.

Shelf Life

Factory sealed containers of this product are guaranteed to be of first quality for one (1) year if stored off the ground in a dry area. High humidity will reduce the shelf life of bagged product.

Limitations

Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproof membranes. When a waterproof membrane is required, use a LATICRETE® Waterproof Membrane.

Note: Surfaces must be structurally sound, stable and rigid enough to sup- port ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L=span length.

Cautions

• Consult SDS for more safety information.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

TECHNICAL DATA

Physical Properties @ 230C

LATICRETE ® 315 with Water

Shear Strength : ANSI 118.1|
Water immersion| >0.5 MPa
Heat ageing| >0.5 MPa
28 days| >0.8 MPa
LATICRETE ® 315 with Latex

Tensile adhesion strength (Impervious tiles): ANSI 118.4
Water immersion| >1.2 MPa
28 days| >1.5 MPa

Working Properties @ 23 0C

Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will de- pend on installation methods and site conditions

INSTALLATION

Surface Preparation

All surfaces should be between 4º C to 35º C and structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with LATICRETE® Latex Portland Cement underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. All slabs must be plumb and true to within 6mm in 3m. Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI Specification AN-3.8 ”Requirements for Expansion Joints” or TCA Details EJ171 “Expansion Joints”. Do not cover expansion joints with mortars. Cement Backer Board; follow TCA installation detail W244.

Mixing

Place clean potable water into a clean pail, Add 315 powder. Use approximately 4.2 – 4.6 Liters of water for 20 Kg bag of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow mortar to slake for 5 –10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application

Apply mortar to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional mortar with the notched side.

Note: Use the proper sized notched trowel to insure full bedding of the tile. Spread as much mortar as can be covered with tile in 15-20 minutes. Back butter large tiles (>20x20cm) to provide full bedding and firm support. Place tiles into wet, sticky mortar and beat in using a beating block and rubber mallet to imbed tile and adjust level. Check mortar for complete coverage by periodically removing a tile and inspecting bedding mortar transfer onto back of tile. If Mortar is skinned over (not sticky), remove and replace with fresh mortar.

Cleaning

Clean tools and tile work with water while mortar is fresh.

AVAILABILITY AND COST

Availability

LATICRETE® materials are available worldwide.

For distributor information,

please contact us by email at: enquiry@laticrete.me or, visit www.laticrete.me

Cost
Contact a LATICRETE® closer distributor to obtain complete information and cost.

WARRANTY

The supplier warrants this product will not deteriorate under normal conditions and use, the warranty validity of one (1) year. The product subject to the terms and conditions stated in the LATICRETE® Product Warranty.

Please consult our technical support for further information.

TECHNICAL SERVICES

Technical assistance

For information contact us by email at: enquiry@laticrete.me

Technical and safety literature
To obtain technical and safety literature, please visit our website at: www.laticrete.me

Warning: The information and the instructions in the data sheet, although based on knowledge gained through years of applications, are indicative. LATICRETE® unable to directly control the installation conditions and modalities of application of products, do not assume any liability arising from their implementation. Those who want to use the LATICRETE® products must conduct adequate tests to determine the site specifications. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation method and site conditions.

CUSTOMERS SUPPORT

© 2022 LATICRETE International, Inc. All trademarks shown are the intellectual properties of their respective owners.
Data Sheets are subject to change without notice. For latest revision, visit www.laticrete.me / www.laticrete.com

References

• Middle East - LATICRETE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>