Puig Honda Rebel 1100 2021-2023 Vintage Frame Sliders Instructions
- June 13, 2024
- Puig
Table of Contents
Puig Honda Rebel 1100 2021-2023 Vintage Frame Sliders
Product Information
The product is a motor protector or crash pads, specifically designed for the Honda Rebel 1100 ’21-’22 model. It is manufactured by Puig, a company known for producing high-quality motorcycle accessories. The product is designed to protect the motor and minimize damage in case of accidental falls or crashes. It consists of various components, including screws, washers, nylon protectors,aluminum spacers, metallic spacers, bars, and rubber trims.
Components:
- Tornillo M12/175×80 DIN912 – 2 pieces
- Arandela M12 DIN433 – 2 pieces
- Protector Nylon Vintage – 2 pieces
- Casquillo aluminio 62mm (Negro) – 2 pieces
- Casquillo aluminio 50mm (Negro) – 2 pieces
- Varilla M12x340 – 1 piece
- Embellecedor goma (Accesorio no incluido)
Product References:
- M2TM12175080A9B
- ARANM12DIN433ZB
- CRASHPADCUSTOMCASQU500-0-1800
- CASQU501-0-1801
- VARILL18-0-0018
- REF.3667
Product Usage Instructions
Follow the steps below to assemble the motor protector on your Honda Rebel 1100:
Assembly:
- The assembly shown in the manual is for the left side. Repeat the same steps for the right side.
- Start by attaching the nylon protector (3) to the designated area on the motorcycle frame using the M12/175×80 DIN912 screws (1) and M12 DIN433 washers (2).
- Place the aluminum spacer (4) with a diameter of 62mm (black) on top of the nylon protector.
- Insert the M12x340 bar (6) into the designated hole on the aluminum spacer.
- If desired, attach the rubber trim (7) as an additional accessory to enhance the appearance.
Note: Refer to our website for the availability of a video tutorial on the mounting process for this specific product reference.
MOUNTING INSTRUCTIONS
INSTRUCTIONS TO ASSEMBLE
Remove the fasteners that subject the chassis to the engine. Mount the
protectors on each own side as the figure below shows. Tight the set, and
place the caps.
All the screws replaced, should be tightened to the torque specified in the
oem maintenance manual for your motorcycle. if no torque specifications are
provided in the oem maintenance manual, may be used 54Nm for all M10 screws.
Medium strength liquid thread-locker (i.e. “Loctite”) should be used to secure
all screws, bolts and nuts. All screws, bolts and nuts should be checked after
driving
the first 50 km to ensure that all are tightened to the proper torque.
FOR TO ASSEMBLE THE CRASH PADS, IF YOU ARE NOT A TRAINED MECHANIC, PLEASE CONTACT A SPECIALIST. MOTOPLASTIC, S.A. TAKES NO RESPONSIBILITY FOR DAMAGES CAUSED BY IMPROPER INSTALLATION. THE USE OF CRASH PADS DO NOT GUARANTEE A FULL PROTECTION IN CASE OF ACCIDENT. MOTOPLASTIC-PUIG DECLINE ANY RESPONSIBILITY IN CASE OF MOTORCYCLE DAMAGE.
DESCRIPTION
1: M12/175×80 DIN912 scres
2: M12 DIN433 washer
3: Vintage Nylon Protector
4: Aluminum spacer 62mm (Black)
5: Metallic spacer 50mm (Black)
6: M12x340 bar
7: Rubber trim (Accessory not included)
ASSEMBLY
The left side assembly is shown as an example, so the same steps can be performed for the right side assembly.
CONSULT OUR WEBSITE THE VIDEO MOUNT AVAILABILITY OF THIS REFERENCE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>