GIGABYTE S55U Gaming Monitor Key Installation Guide

GIGABYTE S55U Gaming Monitor Key

What’s in the box

• Your Gigabyte monitor comes with the following items:
• monitor
• power cord
• remote control
• 1 set of AAA (1.5Vcc) batteries
• 2 base stands
• 4 screws (M5×16)
• 1 HDMI cable
• Multilingual Installation Guide (this document)
• warranty card
• Regulatory Notices & Safety Precautions

IMPORTANT:

• To prevent accidentally discarding items that came with your monitor, be sure to check ALL of the foam in the carton box.
• Please check the foam for accessories before discarding it.
• Veillez vérifier la mousse pour qu’il n’y ait pas d’accessoires avant de la jeter.
• Antes de desechar la espuma, asegúrese de retirar todos los accesorios.
• You will also need the following items (which are not included) to set up your monitor:
• Wireless router (not included) for Internet connectivity
• Phillips screwdriver (not included) to secure the monitor stand
• Not all connection cables are included. Some cables are sold separately to connect external devices to the monitor.
• Wall mount bracket and screws (not included) if you prefer to mount the monitor on the wall
• Disclaimer: This Multilingual Installation Guide is intended as a general guideline to help you set up your monitor. Images throughout this document are for illustrative purposes only and might differ from the actual product.

Getting started

• Step 1. Attach stand or mount
• Before you start using your monitor, attach your monitor stand or mount it on the wall.

CAUTION:

• Disconnect the AC power cord before installing a stand or a wall mount bracket.
• The LED display on your monitor is fragile. Make sure the monitor screen is not scratched or damaged by hard objects or pressure.
• After the installation is complete, make sure the monitor is steady on a table or firmly attached to a wall mount, before removing all protective film, if any.
• Attach the monitor stand

To attach the monitor stand legs to your monitor:

1. Carefully place your monitor face down on a clean, soft, and flat surface.
2. Insert the monitor base stands into the bottom slots on your monitor.
3. Use the screws provided to secure each base stand tightly.

Attach the wall mount bracket (not included)

Before you begin the third-party manufacturer instructions, be sure to do the following things:

1. Place the monitor face down on a clean, safe, and cushioned surface.
2. Remove the monitor stand if you have already attached it.
3. Remove the four screws on the back of the monitor.
4. Place spacers (not included) in the corresponding bracket holes.

CAUTION:

• Follow the instructions provided with the wall mount bracket. If it is not correctly mounted, the monitor may fall and cause property damage or personal injury.
• When you attach the mount, be sure to use spacers (provided by the third-party manufacturer between the monitor and the bracket.
• To prevent internal damage to the monitor and to ensure it is mounted securely, be sure to use fixing screws (not included) that are 8.0 – 10.0 mm in length when measured from the attaching surface of the rear cover.
• Wall mount hole pattern(mm) 400 × 300
• Wall mount screw size M6
• We do not recommend hanging the monitor on a slanted wall and when wall mounting make sure your monitor remains parallel to the wall and does not lean forward.

NOTE:

• If you have additional questions, please contact the wall mount manufacturer or the retailer from which you purchased the monitor.
• The diameter and length of the screws differ depending on the wall mount bracket model.

Step 2. Connect devices to your monitor

• Check to ensure that you have connected the right cables for the right ports securely. Loose connections can affect the quality of the picture image and color.

**

**Get to know controls

Control of the monitor

• The Google Assistant can answer your questions or help you change monitor configuration.
• Before using this function, connect the monitor to the Internet and sign in to your Google account at Settings > Accounts & Sign In.
• How to use the Google Assistant function via the control button on your monitor:

1. Switch the button to [ ] to turn on the Google Assistant.
2. Start a conversation by saying “Hey Google”, and the dialog bar appears at the bottom of the monitor screen. At the same time, the voice indicator illuminates.
3. Continue speaking, such as “What’s the weather” or “Volume up”.

Screenless Mode

• Talk to the Google Assistant even when the screen is off.
• In Screenless Mode, Google Assistant is always available to help even when the screen is not on. Just say “Hey Google”.
• This feature will affect standby power consumption. To turn it off, go to Settings >

Advanced System > Screenless Mode

• NOTE: The Google Assistant and some features are available in a limited country/ region/language.

Get your remote ready

• The following table shows the buttons on your remote control and describes what they are for.
• NOTE: Buttons listed here are for reference only. Actual remote control models may vary.

Insert the batteries

1. Take off the back cover to open the battery compartment of the remote control.
2. Insert two AAA(1.5Vcc) size batteries. Make sure to match the (+) and (-) ends of the batteries with the (+) and (-) ends indicated in the battery compartment.
3. Restore the battery compartment cover.

Remote control range information

• The remote control can work at a distance of up to 26 feet (792.5 cm) in front of the monitor set.
• It can work at a 30 degree horizontal or vertical angle.

Pairing the remote control

1. Pair the remote to the monitor after you power it on. Keep the remote control within 10 feet (304.8 cm) from the Monitor. Press and hold the button at least 3 seconds to start pairing.
2. If the remote pairs successfully, a confirmation will display on the screen. If it does not pair successfully, an unsuccessful message will display. Repeat step 1.

NOTE:

• If an unknown error occurs with the remote, it could have been caused by interference. Try to remove what’s causing the interference and pair the remote again.
• If an unknown error occurs with the remote control while the battery power is normal, you can take out the batteries and press any key for 1-2 seconds, and the remote control can work normally.
• The remote cannot be paired to the monitor while the monitor is in the standby mode.

Power on the monitor

• Connect your power cord to the monitor and plug it into a power outlet.
• Your monitor will display a launch screen showing the Gigabyte logo.

NOTE: S/N refers to the label at the bottom left of the monitor back cover.

Complete the first-time setup

• The first time you turn on your monitor, there is a guided setup to make it easy to connect your monitor to the Internet and complete the setup of your monitor.

Establish a network connection

1. Press the Home button on the remote control, and select the icon to select Settings to enter the Settings menu.
2. Select Network & Internet.

Establish a wired network connection

Automatically obtain an IP address

1. If you connect to the wired network, the monitor will automatically obtain an IP address and connect to the network.
   • NOTE: The default option of IP Settings Mode is DHCP.
2. If the connection fails, “Not connected” will display for the Ethernet status. Retry or enter the IP settings, and select Static to input the information again.

Manually enter the IP address

1. Enter the IP settings to select Static.
2. Enter the IP address, Gateway, Network prefix length, DNS 1 and DNS 2 in the menu.

Establish a wireless network connection

The monitor can directly receive network signals via wireless router.

1. Turn on yourWi-Fi.
2. The list of networks will display automatically.
3. Select a wireless network from the list, input the password.
4. If the network connection does not appear in the list, select See all to display all the list, or select Add new network to input a Wi-Fi name, select the type of security mode, and enter password.

Close the network connection

• Unplug the network cable or turn off your Wi-Fi. The network connection will close.

Enjoy your monitor!

• Now that you’ve completed the first-time setup, your Home screen is your starting point for using your monitor. Your Gigabyte monitor provides a variety of entertainment options, so you’ll always find something new.
• Press the Home button on your remote to get started.

Product specifications

Disclaimer: All products, product specifications, and data are subject to change without notice to improve reliability, function, design or otherwise.

Certification and compliance

• Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Dolby Vision IQ is a trademark of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright© 2012-2021 Dolby Laboratories. All rights reserved.
• For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD Master Audio, DTS-HD, Virtual:X, and the DTS-HD logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
• Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Precautions in the Users
• Manual before using the machine.
• The photos are for reference only. Specifications may vary by model.
• We endeavor to present the most accurate and comprehensive information at the time of publication, we reserve the right to make changes without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>