Reber 9340 N Automatic Vacuum Sealer Horizont Animal Care User Guide

Reber 9340 N Automatic Vacuum Sealer Horizont Animal Care

Product Information

The product is a vacuum sealer machine designed for food storage and preservation. It comes in various models, including the SALVASPESA 9340 N, 9342 N, 9342 NS, 9342 NT, 9342 NB, 9342 NR, 9344 N, 9346 N, 9346 NF, 9348 N, 9348 NF, and the FAMILY 9700 N, 9700NF, 9701 N, and 9701 NF. The machine operates by removing air from specially designed embossed vacuum bags to create an airtight seal, extending the shelf life of perishable foods and preventing freezer burn. It is equipped with a vacuum pump and a sealing bar.

Product Usage Instructions

1. Ensure that the machine is placed on a flat and stable surface.
2. Do not immerse the machine in water or use it if the plug or power cord is wet.
3. Before using the machine, familiarize yourself with the images ofthe operation provided in the user manual.
4. Pay attention to the heated elements on the sealing bar during machine operation.
5. Use embossed vacuum bags specifically designed for food storage. Avoid mixing different types and brands of bags.
6. Always disconnect the power cord from the socket before performing any maintenance or cleaning tasks.
7. Vacuum packaging does not replace other food preservation methods. Perishable foods still require refrigeration or freezing.
8. Pre-packaged products should be consumed before their indicated expiration date.
9. Liquids should be refrigerated before vacuum sealing to prevent spillage or aspiration into the vacuum chamber.
10. Powder or granular products should be covered with a napkin before vacuum sealing to avoid clogging the valve or damaging the pump.
11. Use only suitable vacuum storage containers in the freezer to prevent implosion due to air pressure.
12. The vacuum pump and sealing system have thermal protection and require a few minutes of cooling down after operation.
13. The machine’s automatic settings are optimized for performance. Avoid starting a cycle immediately after plugging in; wait for the recommended minimum time (15 seconds) before starting.
14. Be cautious of the hot sealing bar to avoid burns.
15. If the power cord is damaged, it should be replaced by a qualified technician with a compatible HAR H05VV-F type cord or equivalent.
16. With practice and experience, you will achieve the best results for different types of food.

For additional instructions and safety information, refer to the user manual provided with the product.

Thank you for purchasing the Reber vacuum packer appliance.

Reber vacuum packers use the latest technology that combines the performance of a professional machine (vacuum level up to -850 mbar, working continuously without interruptions for cooling, electronic control of the power supplied to the sealing bar) with reduced electrical consumption, in compliance with the latest standards on the performance of household electrical appliances.

REBER energy-saving technology allows the motor to supply more power with electrical consumption reduced by 50% compared to normal vacuum packers, and to control the quantity of heat supplied to the sealing bar independent of the voltage mains to always have perfect sealing. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved

Reber follows a policy of continuous research, evolution and change of its products in the legislative, technical, ecological and business fields. Any deformities of the product compared to this instructions booklet are the result of this process.

MANUFACTURER’S RESPONSIBILITY

• The manufacturer cannot be held liable for problems, breakages, accidents, etc. due to lack of know-how (or however non-application) of the specifications contained in this manual.
• The same can be said for the implementation of changes, variants and/or installation of accessories unauthorised in advance.
• This appliance is only intended for household use, unless otherwise expressly indicated.

WARNINGS

• Pay attention, during machine operation, to the presence of heating elements on the heating bar.
• Use embossed bags to store vacuum-packed food, the same type and brand as those supplied; operation of the appliance is not guaranteed with other types and brands of bag.
• Do not place the appliance in water and do not use it if the plug or the cable attached to the plug is wet.
• Every type of intervention on the appliance, including the cleaning operations must be carried out with the plug cable disconnected from the power socket.
• Vacuum packing does not replace other preservation procedures, but can be used alongside them
• Perishable foods however require refrigeration or freezing to avoid deterioration; vacuum packing lengthens their preservation time and maintains their organoleptic qualities intact.
• The pre-packaged products must be in any case consumed with the expiry date indicated on the packaging.
• A higher vacuum level indicates less presence of oxygen, and therefore the possibility of better preservation.
• Liquids must be refrigerated before being packaged in vacuum pack bags to prevent them from leaking or suctioning in the vacuum chamber.
• Powder products and grains must be covered with a napkin before being vacuum packed to avoid them being sucked into the vacuum chamber, which would obstruct the valve or damage the pump.
• Containers not suitable for vacuum packing preservation can implode due to the effect of the air pressure, causing damage and injury; for freezer preservation, only use the specific tempered glass jars for freezers.
• The vacuum pump and the sealing system are equipped with thermal protection; in the event of overheating, the machine automatically stops and can start working again only after a few minutes of cooling.
• The automatic operating settings were created at the time of manufacture to obtain the best performance of the machine, in terms of safety and reliability. If in particular cases, different performance is required to those pre-set, you need to proceed in manual mode.
• If you don’t wait the minimum time required between the connection to the mains and the start of the work cycle, you need to disconnect and re-insert the plug in the socket and wait the minimum time required (15 seconds).
• When using with containers it is recommended to use the appliance in Manual mode and to pay close attention to the heating of the sealing bar, to avoid burns.
• If worn, the cable should be replaced by a specialist technician with cable type HAR H05VV-F or however equal to the cable supplied.
• Practice and experience will allow you to obtain the best results from the appliance with every different type of food.
• For its use, pay attention to the appliance is on a flat and stable surface.
• To work, the appliance must be connected to a power socket that is always easily accessible during use.
• Acoustic level under 60 dBA.
• Minors must not play with the appliance.
• Cleaning and maintenance of the appliance must not be carried out by unsupervised minors.

INFORMATION ON VACUUM PACK PRESERVATION

VACUUM PACKING:
It means removing the air from a container or bag, to preserve the content from harmful effects caused by oxygen, such as oxidation or development of mould and bacteria. All the objects, in contact with the air, are subject to alterations; these alterations are particularly obvious in food. The air and humidity in foodstuffs cause mould and micro-organisms to develop, a loss of flavour and smell and colour alterations. Preservation systems, such as refrigeration, freezing and drying, have the purpose of reducing and preventing such alterations; vacuum packing, thanks to air extraction, considerably lengthens the preservation period of the foodstuff whether fresh or preserved. To make the vacuum time efficient and lasting, the container and the bag must be correctly sealed.

VACUUM PACKING PRESERVATION
Preservation, especially of foodstuffs, takes place using particular humidity and temperature conditions (for example in the press, refrigerator or freezer); vacuum packing, in addition to the normal preservation methods, considerably lengthens the time these products can be preserved. Vacuum packing preservation also enables the flavour, smell, colour and nutritional quality of the food to be unchanged.

WHY PRESERVE WITH VACUUM PACKING?

BECAUSE IT SAVES YOU MONEY:
You can purchase larger quantities of products and in the periods most indicated, keep them fresh and intact thanks to vacuum packing!

BECAUSE YOU AVOID WASTE:
The portions of excess food will not go to waste, but can be kept and used later! BECAUSE IT SAVES YOU TIME: You can conveniently cook your meals, preserve them in vacuum packs and use them as you wish, simply by reheating them!

BECAUSE IT’S MORE HYGIENIC:
Vacuum packaging prevents the development of mould, bacteria, and micro- organisms and allows you to use the refrigerator and the freezer, avoiding the risk of contamination among foodstuffs and the dispersion of odours!

BECAUSE IT IS SIMPLE:
With Reber appliances, everyone can obtain professional quality vacuum packing at home, using the most suitable appliance for your needs, and a complete series of accessories for any type of preservation. Double layer vacuum packing bags, containers in polycarbonate also for oven, microwave and freezer use, and dishwasher safe, universal round and rectangular lids for use with containers, bowls, jars and saucepans for normal household use, small, re- usable lids for glass jars!

WARNINGS
The preservation time of the food greatly depends on the initial conditions of the food. Vacuum packing does not replace other preservation systems. Food that requires appropriate temperature conditions must be kept in the fridge or freezer even if vacuum packed. All pre-packaged products must however be consumed before the expiry date indicated on the packaging. Some types of fruit and vegetables must be peeled or blanched and frozen before vacuum packing.

Food preservation times (in days)| in normal vacuum| | conditions
---|---|---|---
At room temperature (+20° / + 25° C)
Bread| 2| 8
Dry biscuits| 120| 360
Dry pasta/rice| 180| 360
Dry fruit| 120| 360
Flour /Tea/Coffee| 120| 360
Refrigerated at +3° / +5° C
Raw meat| 2 – 3| 6 – 9
Fresh fish| 1 – 3| 4 – 6
---|---|---
Cold cuts| 4 – 6| 20 – 25
Soft cheese| 5 – 7| 14 – 20
Hard and mature cheese| 15 – 20| 30 – 60
Parmesan/Grana Padano| 20| 60
Raw vegetables| 1 – 5| 7 – 20
Raw fruit| 5 – 10| 14 – 20
Vegetable purée /Minestrone| 2 – 3| 8 – 15
Pasta/Risotto /Lasagne| 2 – 3| 6 – 10
Cooked meat| 3 – 5| 10 – 15
Desserts filled with cream or fruit| 2 – 3| 6 – 10
Other desserts| 5| 20
Frozen at -18° / -20° C
Meat| 120| 480
Fish| 90| 360
Fruit and vegetables| 300| 720
ATTENTION

The preservation times are approximate and depend on the initial conditions of the products and the preparation times.

INSTALLATION

Install the product on a flat surface that takes into consideration the dimensions of the appliance, levelled, smooth, dry, and robust, with a height off the ground of approximately 80 cm and with the useful space necessary around it for use and maintenance.

Environmental conditions:

• Minimum temperature +10°
• Maximum temperature + 30°
• Minimum humidity 30%
• Maximum humidity 80%

GENERAL USE MANUAL

• Having inserted the power supply plug in an adequate socket, wait 15 seconds before starting operations.
• The appliance is set and guaranteed for use with Reber branded embossed bags, the functionalities of the appliance are not guaranteed in the event of use with different bag types or brands.
• The vacuum packers with external suction are not suitable for use with products with a high rate of humidity. Any suction of liquids can damage the appliance (pump, electronic data sheet and gaskets of the vacuum chamber); such damage is considered improper use of the machine and is not covered by warranty.
• The appliance must be kept in a dry place at a temperature of between +10° and + 30°.
• The bags, especially if the packaging is open, must be kept in a dry place at a temperature of between +10° and + 30°.

GENERAL SETTINGS

The factory settings include

• Electronically set sealing power of 5 time/power units, suitable for the bags supplied, with a thickness of 95/105 microns.
• The sealing power set can be modified using electronic programming using the appliance buttons.
• The appliance is prepared for automatic use of the vacuum/sealing cycle, simply by pressing the start button, without any other use of the
• Pressing the start button during the functioning of the appliance terminates all other operations, stopping both the pump and the sealing
• Electronic programming enables manual functioning
• In manual operating mode, you need to press and release the start button to start the air suction operation and press and release the sealing button to start the sealing
• ATTENTION: if the sealing button is pressed during the sealing operation, the sealing operation is
• The appliance is prepared for a standby time of 3 seconds between reaching the vacuum level set and the start of the sealing process (super vacuum function).
• The appliance is prepared for a standby time of 7 seconds at the end of the sealing operation to obtain better sealing quality. 30- The appliance is equipped with a welding booster function which increases the welding time by 20% for the first 3 work cycles, beyond 3 cycles, if the appliance is not used for more than 5 minutes, it is advisable to disconnect the appliance from the network to reinitialize the system and use the booster again.

NOTE : The optimal sealing time can vary based on the type of bag used and the temperature and humidity conditions; you are advised to carry out any tests checking the result. Reduced sealing power will speed up the duration of the cycle and will enable longer working without the thermal protection activating.

IMPORTANT: In the event of long periods of non-use and/or low temperatures in the work or storage environment of the appliance and the bags, before carrying out the packing procedure, you are advised to keep the pump on for at least a minute and to carry out a vacuum/sealing cycle with a bag, with the cover closed. This operation allows the removal of any residual humidity in the sealing zone and establishes the temperature of the pump operation.

VACUUM PACKING IN BAG

• Prepare the product by eliminating any roughness that could perforate the preservation
• Insert the product in a bag suitable for the preservation of vacuum-packed food, leaving at least 5 cm of free space from the bag opening;
• Lift the cover of the machine and rest the well-laid bag on the sealing bar, taking care to insert the open side of the bag in the vacuum chamber. Image 1
• Insert the cable plug in an electricity socket, start the vacuum pump by pressing the switch (1) and exerting light pressure with your hands on the cover to create a first negative pressure in the vacuum chamber; you don’t need to press until the end of the operation, but only until the bag starts to stick to the
• At the end of the sealing operation, the machine stops. The cover will automatically
• Before placing the bag back for preservation, you should check the good quality of the sealing, i.e. the absence of folds or impurities that could enable air

VACUUM PACKING IN ROLL SEALING OPERATION WITHOUT VACUUM

• Lift the cover of the machine and rest the well-laid bag or portion of roll on the sealing bar, taking care NOT to insert the open side of the bag in the vacuum chamber. (image 2)
• Start the vacuum pump by pressing the switch (1.) and exert light pressure with your hands on the cover to create a first negative pressure in the vacuum
• At the end of the sealing operation, the machine stops. Open the cover.
• Cut the sealed roll to the desired length and proceed to vacuum pack as described in the previous chapter

VACUUM PACKING WITH REBER ACCESSORIES AND CONTAINERS
(ONLY FOR MODELS EQUIPPED WITH AIR INTAKE FOR CONTAINER VACUUM PACKING

this operation requires containers with lids with a vacuum valve and a specific attachment for containers; only use containers suitable for vacuum packing, in plastic or tempered glass)

Always set the manual operating cycle to avoid damaging the sealing bar The product to be vacuum packed must always be at room temperature in order not to damage the container and the lid

• Lift the cover of the machine and identify the air intake
• Insert the tube of the attachment for containers in the air intake
• Fill the container leaving at least 3 cm. of free space from the upper edge, and position the intake
• Slightly unscrew the plug on the lid so the valve is released; ( ATTENTION : the plug must NOT be unscrewed completed, a few turns is enough).
• Position the attachment on the plug, covering the valve
• Start the pump on the vacuum until the desired vacuum level is reached; WARNING : Stop the vacuum when the Red Light ( if present) light on o when the needle reach the Red
• Once the machine is switched off, remove the attachment for containers from the lid and screw in the plug until the valve is
• To open the container, slightly unscrew the plug until the valve is released, then move the valve so air enters the

VACUUM PACKING WITH REBER UNIVERSAL LIDS

(The REBER universal lids in various measurements to adapt to containers, jars, bowls, saucepans and dishes, for normal household use, with a diameter of 4 to 22 cm.)

• Proceed as per vacuum packaging in the container, taking care the edge of the container used sticks perfectly to the universal lid
• In case of prolonged use on the same container, the seal of the lid can have a groove left by the edge of the container; to eliminate any use problems, you must rotate the gasket on the opposite side; then the groove with shortly disappear by
• The seal of the lids can be removed for washing; once dry they must be correctly positioned; Attention! The seal must be washed exclusively by hand with lukewarm

THE VACUUM LEVEL
REBER vacuum packers come with a vacuum sensor installed on the electronic board that detects reaching the vacuum level obtained on the bag or container, controlling the start of the sealing function (automatic operation). Certain models are also equipped with a device (LED and/or vacuum gauge with hand) that enables the user to check the vacuum level created: switching on the red LED and/or the hand in the red zone of the vacuum gauge indicates the optimal vacuum level has been reached. It is however possible to delay the start of the sealing operation to obtain a greater vacuum level, i.e. not damage the machine in any way.

The vacuum level reachable by the machine is conditioned by the equality and shape of the food (or objects) in the bag. Some food (fish, tomatoes, etc.) contain liquids that when compressed leak and can be sucked in causing damage to the machine, and foodstuffs that due to their poor consistency can become crushed or damaged by an excessive vacuum level; for this food, you are advised to check the level of adherence of the bag and proceed to weld before any crushing.

SALVASPESA Line
Vacuum level display dealing bar 32 cm (for 30 cm bags). Air intake for container attachment. Absorbed maximum power: 180W Vacuum maximum level: -850 mbar Suction capacity: 18 l/min Included in the packaging, unless otherwise indicated on the packaging: 20 bags 20×30 cm

Models: 9340 N, 9342 N, 9342 NS, 9342 NT, 9342 NB, 9342 NR, 9344 N, 9346 N, 9346 NF, 9348 N, 9348 NF

Family Legend

Salvaspesa legend

23. Vacuum pump start switch;
24. Sealing switch;
25. Pump on yellow led
26. Vacuum packing green led
27. Vacuum level red led
28. Cover;
29. Cover opening valve;
30. Vacuum chamber;
31. Sealing bar;
32. Air suction socket;
33. Guide;

USE MANUAL

• Insert the power cable plug in an electricity socket corresponding to the voltage planned and wait 15 seconds, the appliance is powered and ready to start
• Pressing the switch (1.)
  • the vacuum pump starts air suction: pressing the switch again, the machine stops
• The appliance will automatically start the sealing cycle once the preset vacuum level has been reached, it is, however, possible at any time to start the sealing cycle by pressing the switch (2.), the machine will automatically stop working after an interval of the programmed time, or when the start switch is
• ATTENTION : if the appliance has already begun automatic sealing, pressing the switch (2.) the sealing function is interrupted and the machine stops after the cooling time
• The green LED (4) also serves as a counter for the sealing time, during this operation the LED flashes as many times as the sealing power unit is set.
• When the red LED switches on it indicate a sufficient vacuum level was reached, it is however possible to delay sealing by passing to manual operation to obtain a higher vacuum level; this operation does not damage the machine in any

CHANGING SETTINGS

The settings programmed will stay saved even after the machine is switched off

SEALING TIME

To change the sealing power set, proceed as follows:

• Connect the appliance to the electrical
• Press and release the sealing button (2) 10 times within 10 seconds; the green LED, if on the model, will quickly flash to indicate you entered the programming
• If the green LED is not flashing, it means the first part of the programming is not correctly
• Press and release the running button (1) as many times as the desired time/power unit; the green LED, if on the model, flashes on each impulse.
• If the running switch is pressed for the first time (1) and the appliance starts the suction function, switch off the machine and repeat the programming
• Wait 10 seconds without pressing the buttons or disconnecting the appliance from the electrical mains, (by doing so, the settings are saved)

ATTENTION!! Do not set more than 9 power units, the Teflon belt on the sealing bar could get damaged beyond that threshold.

TO RESET THE INITIAL FACTORY VALUES:

• Disconnect the machine from the electrical
• Press the buttons and keep them
• Insert the plug in the electricity
• Wait for the green LED to switch on and release the

PASS FROM AUTOMATIC TO MANUAL FUNCTIONING:

• Disconnect the machine from the electrical
• Press the start button and keep it
• Insert the plug in the electricity
• Wait for the green LED to switch on and release the

PASS FROM MANUAL TO AUTOMATIC FUNCTIONING:

• Disconnect the machine from the electrical
• Press the sealing button and keep it
• Insert the plug in the electricity
• Wait for the green and red leds to switch on and release the

**VACUUM PACKING

**

• – Insert the product in a bag suitable for the preservation of vacuum-packed food, leaving at least 5 cm of free space from the bag opening;
• – Lift the cover of the machine (6.) and rest the well-laid bag on the sealing bar (9.), on the left of the guide (11.), taking care to insert the open side of the bag in the vacuum chamber (8.). (Figure 1)
• Insert the power cable in the electricity socket which is easily accessible, and wait at least 15
• – Start the pump by pressing the switch (1) and exerting light pressure with your hands on the cover (6.) to create a first negative pressure in the vacuum chamber; you don’t need to press until the end of the operation, but only until the bag starts to stick to the
• The appliance will automatically start the sealing cycle once the preset vacuum level has been reached, it is however possible at any time to start the sealing cycle by pressing the switch (2.).
• At the end of the sealing operation, the machine stops automatically; Models 9340 N – 9340 NAUS – 9340 NCSA– 9342 N (S- T-R-B): push the cover valve to the side (7.) to lift the cover and remove the bag. Models 9346 N (F) – 9348 N (F) the cover can be immediately lifted at the end of the vacuum/sealing
• Before placing the bag back for preservation, you should check the good quality of the sealing, i.e. the absence of folds or impurities that could enable air passage. (Figure 4)

Line: FAMILY

• Professional vacuum gauge.
• Sealing bar 32 cm (for 30 cm bags).
• Continuous functioning.
• Cover opening solenoid valve;
• Air intake for container attachment.
• Absorbed maximum power: 190W
• Vacuum maximum level: -850 mbar
• Suction capacity: 18 l/min
• Included in the packaging, unless otherwise specified on the packaging:
• Attachment for containers, 20 bags 20×30 cm

Models : 9700 N, 9700 NF, 9701 N, 9701 NF, 9703 N

Family Legend

9. Vacuum pump start switch;
10. Sealing switch;
11. Vacuum gauge;
12. Cover;
13. Vacuum chamber;
14. Sealing bar;
15. Air suction socket;
16. Guide;
17. Attachment for containers;
18. Tube;
19. Bar

USE MANUAL

• Insert the power cable plug in an electricity socket corresponding to the voltage planned and wait 15 seconds, the appliance is powered and ready to
• Pressing the switch (1.) the vacuum pump starts air suction: pressing the switch again, the machine stops
• The appliance will automatically start the sealing cycle once the preset vacuum level has been reached; the machine will automatically stop working after an interval of programmed time, or when the start switch is
• ATTENTION : if the appliance has already begun automatic sealing, pressing the switch (2.) the sealing function is interrupted and the machine stops after the cooling time

CHANGING SETTINGS

The settings programmed will stay in the memory even after the machine is switched off

SEALING TIME

To change the sealing power set, proceed as follows:

• Connect the appliance to the electrical mains
• Press and release the sealing button (2) 10 times within 10 seconds;
• Press and release the running button (1) as many times as the desired time/power.
• If the running switch is pressed for the first time (1) and the appliance starts the suction function, switch off the machine and repeat the programming
• Wait 10 seconds without pressing the buttons or disconnecting the appliance from the electrical mains, (by doing so, the settings are saved)

ATTENTION! Do not set more than 9 power units, the Teflon belt on the sealing bar could get damaged beyond that threshold.

TO RESET THE INITIAL FACTORY VALUES:

• Disconnect the machine from the electrical
• Press the buttons and keep them
• Insert the plug into the electricity preservation
• Wait 5 seconds before releasing the switch

PASS FROM AUTOMATIC TO MANUAL FUNCTIONING:

• Disconnect the machine from the electrical
• Press the start button and keep it
• Insert the pluginton the electricity switch
• Wait 5 seconds before releasing the preservation

PASS FROM MANUAL TO AUTOMATIC FUNCTIONING:

• Disconnect the machine from the electrical
• Press the sealing button and keep it
• Insert the pluginton the electricity switch
• Wait 5 seconds before releasing the preservation

VACUUM PACKING IN BAG

• Insert the product in a bag suitable for the preservation of vacuum-packed food, leaving at least 5 cm of free space from the bag opening;
• Lift the cover of the machine (4.) and rest the well-laid bag on the sealing bar (7.), on the left of the guide (9.), taking care to insert the open side of the bag in the vacuum chamber (6.).
• Close the cover switch
• Insert the power cable in the electricity socket which is easily accessible, and wait at least 15
• Start the pump by pressing the switch (1) and exerting light pressure with your hands on the cover (4.) to create a first negative pressure in the vacuum chamber; you don’t need to press until the end of the operation, but only until the bag starts to stick to the switch
• The vacuum gauge indicates the vacuum level (negative pressure) created by the vacuum pump; this level can be considered a precise measurement of 100% of the vacuum level inside the bag or the container because it is influenced by the dimensions and the shape of the product inserted. During machine operation, the hand will move from the yellow zone (vacuum minimum level) to the red zone (maximum level).
• The vacuum gauge hand has initial strong oscillations, due to air extraction; when the quantity of air in the tubes decreases the hand
• The appliance will automatically start the sealing cycle once the preset vacuum level is
• At the end of the sealing operation, the machine automatically stops and you can lift the cover and remove the sealed
• Before placing the bag back for preservation, you should check the good quality of the sealing, i.e. the absence of folds or impurities that could enable air passage. (Figure 4)

VACUUM PACKING WITH REBER ACCESSORIES AND CONTAINERS
(For this operation you will need containers with vacuum valve lids; only use containers suitable for vacuum packing, in plastic or tempered glass).

• The product to be vacuum packed must always be at room temperature in order not to damage the container and the lid

• Insert the tube of the attachment for containers in the air

• Fill the container leaving at least 3 cm. of free space from the upper edge, and position the

• Slightly unscrew the plug on the lid so the valve is released; (ATTENTION: the plug must NOT be unscrewed completed, a few turns is enough).

• Position the attachment for containers on the switch

• Start the vacuum pump by pressing the start switch (1.) bringing it to the ON position (I).

• Once the desired vacuum level is reached, shut off suction by pressing the switch (1.) and bringing it to the OFF (O)

• Remove the attachment for containers from the lid and screw in the plug until the valve is

• To open the container slightly unscrew the plug until the valve is released, then move the valve so air enters the

VACUUM PACKING WITH REBER UNIVERSAL LIDS
(The REBER universal lids in various measurements to adapt to containers, jars, bowls, saucepans and dishes, for normal household use, with a diameter of 4 to 22 cm.)

• Proceed as per vacuum packaging in the container, taking care the edge of the container used sticks perfectly to the universal lid
• In case of prolonged use on the same container, the seal of the lid can have a groove left by the edge of the container; to eliminate any use problem, you must rotate the gasket on the opposite side; then the groove with shortly disappear by
• The seal of the lids can be removed for washing; once dry they must be correctly

VACUUM PACKING WITH LARGE ATTACHMENT FOR GLASS JARS
(For this operation, you need to use the specific lids for glass jars code 6706 A and the large attachment for glass jars model JUNIOR 6704 A)

• Insert the plastic tube of the attachment for glass jars in the suction air intake (4.) on the jar
• Fill the jar leaving at least 3 cm. of free space from the upper jar
• Position the lid on the glass jar
• Position the large attachment on the jar and push to block its seal on the glass jar
• Turn the top part of the attachment to the CLOSE REBER
• Start the vacuum pump by activating the switch (1.) bringing it to the ON position. (I).
• Once the desired vacuum level is reached, press the switch (1.) to bring it to the OFF (0) position and stop
• Turn the top part of the attachment to the OPEN REBER
• Remove the attachment for containers from the jar and screw in the ring nut until the lid is blocked
• To open the jar, unscrew the ring nut and lift the lid with the specific REBER lid lever code 6713 A to allow air into the jar

UNDERSTAND AND RESOLVE DOUBTS ABOUT THE CORRECT USE OF THE APPLIANCES FOR VACUUM PACKING

The appliance is tested at the time of manufacturing with at least 3 vacuum/sealing cycles. If you are having difficulty during use, doubts or problems, you can proceed with some tests to check the efficiency of the product.

Auto-diagnosis tests

Internal component operation:

• With the cover open, press the start button and close the air press with a finger. (image 6)
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) and sealing automatically starts, the internal operation is
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) but sealing does not automatically start, you need to set the machine for automatic operation and try
• If the hand on the vacuum gauge does not reach red (and/or the red light does not switch on) the vacuum pump is damaged or there is an air leak in the internal tube circuit – contact a support centre for

Operation of the cover and gaskets on the vacuum chamber:

• Close the cover on the machine (without inserting the bag), press the start button and exert light pressure on the cover to start the automatic cycle. (image 7)
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) and sealing automatically starts, machine operation is
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) but sealing does not automatically start, you need to set the machine for automatic operation and try
• If the hand on the vacuum gauge does not reach red (and/or the red light does not switch on), you need to check the chamber gaskets of the vacuum (clean the gaskets or replace them) and try

Bag insertion test:

• Lift the empty bag.
• Position the open end of the empty bag in the chamber of the vacuum, between the gaskets in the vacuum chamber. (image 1)
• Lower the cover, press the start button (1.) and exert light pressure on the cover to start the automatic
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) and sealing automatically starts, machine operation is
• If the hand on the vacuum gauge reaches red (and/or the red LED switches on) but sealing does not automatically start, you need to set the machine for automatic operation and try
• Using these tests, you can check machine operation and get the correct insertion of the bag in the vacuum chamber.
• Correct packaging is only obtained if enough free space is left between the product and the machine (approx. 5 cm. is usually enough) provided the bag can be inserted well laid between the gaskets of the vacuum chamber, without creating folds that could create air leaks, reducing the vacuum level and the quality of sealing.

The machine does not start:

Check you have correctly inserted the plug in the electricity socket and the press is powered.

The bag is not well sealed/air is entering the bag:

• During the winter period, and in the presence of extreme temperature changes, the sealing bar can fill with humidity. On the first start-up of the cold machine, you should execute a completed vacuum/sealing cycle with the cover closed (also without a bag) to reset the machine and stabilise the temperature and humidity conditions. To avoid problems also on first use, the appliance must be kept in a dry place at a temperature of between +10° and + 30°.
• The bags are composed of an outer layer of nylon to protect against air intake; the nylon tends to absorb humidity, especially in the presence of temperature changes; the humidity absorbed prevents correct sealing: to solve the problem, the bags must be kept in a dry place at at temperature between +10° and + 30°.
• The humidity absorbed by the outer layer of the bag can be eliminated by sealing the bag
• Check you have left sufficient free space between the product to pack and the opening of the bag; a limited space creates folds and bends to prevent correct sealing and limits the vacuum level
• Check you have cleaned the opening of the bag near the sealing point; any impurities deriving from the passage of the product to the package prevent correct
• Check you have removed all possible roughness that could perforate the bag; the machines create a high vacuum level with resulting adhesion of the bag to the product, any point or roughness can create micro-pores in the bag to let air
• Humid products can cause liquid to rise towards the opening of the bag, damaging sealing; check you have dried the products to package or use a double bag; insert the product in a first bag, fold the mould of the bag a few times (image 8) and place it in a second bag with the opening folded of the first turned towards the bottom of the second (Images 9 and 10). You can execute the vacuum function and any residual liquids will stay in the first bag without passing into the second, as such obtaining efficient sealing. (image 11) 28- When you use rolls, the first sealing must be carried out by positioning the mouth on the roll (image 2) on the sealing bar and not in the vacuum chamber; the machine seals correctly only if the cover exerts correct pressure on the sealing bar. Anticipating sealing before having a sufficient vacuum level can create channels with air passage and make sealing inefficient. You are advised to carry out a complete automatic vacuum/sealing
• Sealing-only function: position the opening of the bag (image 2) on the sealing bar and not in the vacuum chamber; the machine seals correctly only if the cover exerts correct pressure on the sealing bar. Anticipating sealing before having a sufficient vacuum level can create channels with air passage and make sealing inefficient. You are advised to carry out a complete automatic vacuum/sealing
• If air enters the bag during the sealing phase and after a correct vacuum/sealing cycle, you need to replace the bag which is probably

The machine does not create a vacuum in the bag:

• Check you have correctly positioned the opening of the bag between the seals of the vacuum chamber. (image 1)
• Proceed with auto-diagnosis tests to ensure the machine is working correctly.
• The machine works correctly with Reber branded, embossed type bags. Different bags may not work adequately; check you have used the correct
• During the summer period (when temperatures are higher) or in the event of prolonged use, the residual heat on the sealing bar can create pre-sealing of the bag to prevent the machine from correctly sucking: decrease the sealing power using the electronic programming to decrease the sealing time, wait a few minutes for the sealing bar to cool and continue to work with a lower sealing power.
• Check the seals on the vacuum chamber; in the event of slight liquid suction the seals can harden and get damaged; in this case, you need to change the

The machine does not automatically seal:

• Proceed with auto-diagnosis tests to ensure the machine is working correctly.
• Start a vacuum cycle and manually seal to check the sealing bar is working correctly.
• Check the electronic settings as described in the paragraph “Reset the factory parameters” or adjust the setting on automatic operation as described in the paragraph “Pass from manual to automatic operation”.
• Check you have left sufficient free space between the product to pack and the opening of the bag; a limited space creates folds and bends on the opening of the bag that limit the vacuum level reachable and prevent the vacuum sensor from starting automatically

The machine does not reach a convenient vacuum level:

• Check you have correctly positioned the opening of the bag between the seals of the vacuum chamber. (image 1) 14- Proceed with auto-diagnosis tests to ensure the machine is working correctly.
• The machine works correctly with Reber branded, embossed type bags. Different bags may not work adequately; check you have used the correct bags.
• Check you have removed all possible roughness that could perforate the bag; the machines create a high vacuum level with resulting adhesion of the bag to the product, any point or roughness can create micro-pores in the bag to let air
• Check you have left sufficient free space between the product to pack and the opening of the bag; a limited space creates folds and bends on the opening of the bag that limits the vacuum level reachable.
• Check the seals on the vacuum chamber; in the event of slight liquid suction the seals can harden and get damaged; in this case, you need to change the seals.

WARRANTY
The appliance is prepared for use with Reber embossed bags of the same type as furnished with the machine, if used with different or other label bags the machine could not have the same performance. This appliance is not intended for use with high-grade humidity food; liquid suction may damage the appliance ( Pump, El. Card and vacuum chamber Gasket) and this is considered inappropriate use and out of warranty cover.

Domestic use:
European warranty covers the machine for 24 months from the purchasing date.

Professional use:
The supplier restricts himself from repairing or replacing all components that should have construction faults in the first 12 months from the date of installation and however not later than 18 months from the shipment date.

Components subjected to normal consumption such as Fuses, Welding bar gaskets, Welding bar resistance, Welding bar covers or Vacuum Chamber Gaskets are excluded from the warranty. The customer must indicate to the supplier, in order du benefit from the warranty, the faults pointing out, the serial number of the machine, the purchase date (from the invoice), and he will have to send the faulty part at his charges for reparation or replacement. The supplier fulfils completely his warranty obligations by the reparation or replacement of the faulty piece. If reparation is requested where the machine is installed, all charges regarding, labour, trip and hotel fees of the technicians will be entirely at the purchaser’s charge. The damage due to inappropriate use, missed maintenance, or tampering is not included in the warranty.

IMPORTANT NOTICE!
REBER develops its products by the destination country. The after-sales REBER services are trained only for reparations concerning products sent directly from REBER on the after-sales service country market, or at least the service centre may have difficulty doing any work on specific products unknown to him. If you need assistance on products sent from third dealers in countries for which the same were not designed, the article has STRICTLY to be returned to the dealer for under warranty or no assistance. The costs of repatriation of the proceeds will be paid by the buyer or the seller by commercial agreements between the parties. Once repatriation Reber will be covered by warranty as required by current regulations.

Disposal of Waste Equipment by Users in Private Households in the European Union This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Evacuación de los equipamientos gastados por los usuarios en los hogares privados en la Unión Europea.

Reber srl  Via Valbrina 11  42045 Luzzara (RE) Italia www.rebersrl.it   E. mail : info@reber-snc.it

References

• Reber Srl - Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>